|
| 1 | Schedule-A |
| 2 | Dismantling of floor, hearth or wall tiling including cement morter bedding (but not backing) and rubbish off the premises. |
| 3 | Demolition of Cement Concrete (un-reinforced) of any description and any position not otherwise specifically provided for and removing the same from Site(s), complete all as specified and as directed. |
| 4 | M&L for 20 mm thick rendering in CM 1:4 by on brick/concrete surfaces of sunken slab, mixed with liquid water proofing compound both floor and wall of sunken slab, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately. |
| 5 | Supply only liquid water proofing compound |
| 6 | M&L applying evenly two coat cemetious/liquid waterproofing coating on sunken slab/ceiling/wall as per manufacturer instructions including cleaning surface complete all as specified. |
| 7 | M&L for PCC 1:5:10 type E2 Using 40mm graded stone aggregate as in filling under floor/sunken slab. |
| 8 | M&L Cement Concrete type B1,1:2:4 (20mm Graded Stone Aggregate) 25 mm thick, as in Floors, etc., and finished the Cement Concrete Surfaces Even and fair with using Extra Cement, complete all as specified and as directed. |
| 9 | M&L for Ceramic coloured non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.11 Sqm but n. exec. 0.18 Sqm laid to required levels and slopes as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement sand mortar ( 1:4) and All joints shall be filled and sealed with approved epoxy grout of matching colour to ensure water resistance and durability. complete all as specified and as directed. |
| 10 | M&L Glazed Ceramic Coloured Tiles, 450x350x7mm thick, on vertical faces such as wall,dado, skirting, etc., over and including 10mm thick screed bed in cement mortar 1:4 Set and Jointed in Neat Cement Slurry on prepared and levelled background. The work includes surface hacking/roughening where required, alignment to true line and plumb, cutting with power tools, and maintaining uniform joint spacing. Joints shall be sealed using White or Coloured Cement matching tile finish. The item includes necessary scaffolding, curing (if cementitious backing used), cleaning, protection complete all as specified and as directed. |
| 11 | S & F vitrified tiles tiles light shade 10mm thick (square/rectangular) polished, area of each tile n.exc. 0.36 sqm, in floor etc.,set and jointed in neat cement slurry over 15mm thick screed bed in CM 1:6 and pointed in white or coloured cement with pigment to match for laying floor fineshes all as specified . |
| 12 | M&L for 20mm thick pre polished granite (any colour) slab laid with 15 mm thick CM 1:4 bedding in door Chowkhat/Frame, Window Cill, plateform etc in floor and skirting/dado surface and jointed with grey cement slurry and pointed in white cement with pigment to match the shade of granite stone including Moulding/rounding and polishing all as specified and directed by Engr-in-charge |
| 13 | M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping, benching, bed block for rungs, window cills etc complete all as specified and directed by Engr-in-charge |
| 14 | Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 15 | M&L Reinforced cement concrete 1: 11/2 : 3 (20 mm graded agg )in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 16 | M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 17 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 18 | M&L Rebaring of mild steel bars upto 150 mm depth incl fixing complete all as specified and complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 19 | S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situ-ation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc., complete all as specified and as directed.Note- Work has to be done in occupied or vacant qtrs as per direction of Engr-in-charge |
| 20 | S&F Galvanised Steel Water Tubing 20mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situ-ation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. |
| 21 | S&F Galvanised Steel Water Tubing 25mm Bore (dia), ‘Medium Grade’ with all ISI marked Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. |
| 22 | S&F Galvanised Steel Water Tubing 32 mm Bore (dia), ‘Medium Grade’ with all ISI marked Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. complete all as specified and as directed. |
| 23 | S & F of centre hole basin mixer (15 mm dia) made of brass with chromium plated finish of approved, suitable for mixing hot and cold water, including dismantling/removal of existing unserviceable mixer of any description, providing and fixing all necessary fittings such as connecting pipes, nuts, washers etc., complete, fixing properly to wash basin and connecting to existing pipeline, testing for leakage and making good of disturbed surfaces, complete as directed by Engineer-in-Charge. |
| 24 | S & F of wall mixer (15 mm dia) made of brass with chromium plated finish for kitchen sink, of approved , including dismantling/removal of existing mixer, providing all required accessories such as wall flanges, connecting pipes, nuts, washers, etc., fixing to wall and connecting to hot and cold water lines, testing for proper operation and leakage, and making good, complete as directed by Engineer-in-Charge |
| 25 | S & F of wall mixer (15 mm dia) made of brass with chromium plated finish, for mixing hot and cold water, of approved, including dismantling/removal of existing unserviceable mixer, providing all necessary fittings such as wall flanges, connectors, PTFE tape, nuts and washers, fixing complete and connecting to pipeline, testing and commissioning and making good of wall surface, complete as directed by Engineer-in-Charge. |
| 26 | S & F of bib cock (15 mm dia) long body, made of brass with chromium plated finish, of approved, including dismantling/removal of existing bib cock, fixing to GI/CPVC pipe or brass ferrule, providing all necessary fittings such as thread seal tape, washers, screws, etc., testing for leakage and making good, complete as directed by Engineer-in-Charge. |
| 27 | S & F of angle stop cock (15 mm dia), fancy type, made of brass with chromium plated finish, of approved , including dismantling/removal of existing stop cock, fixing to pipeline with all necessary fittings such as nuts, washers, PTFE tape, etc., testing for proper operation and leakage, and making good of surfaces, complete as directed by Engineer-in-Charge |
| 28 | S&F Brass CP Health Faucet with 1.00m long tube and holder as Approved, including Taking down un serviceable Health Faucet of any description, complete as all specified and directed. |
| 29 | S&F SS Chromium Plated Towel Rail 600/750 mm Long and 20mm dia, as Approved, fixed including Taking down un serviceable Towel Rail of any description, complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F stop valve CP 15mm bore (concealed type) of heavy-duty brass/cast copper alloy body with chrome plated finish, suitable for high pressure, complete with all standard accessories, unions, nipples, PTFE tape, etc., as required, including cutting and making good the wall surface, proper alignment, testing for leakage and smooth operation, complete in all respects as per site requirements and as directed by Engineer-in-Charge |
| 31 | M&L Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) of approved make and quality, including all necessary fittings such as fixing bolts, connection to existing soil pipe, cutting and making good the floor/wall as required, jointing with cement mortar and sealing to ensure leak-proof performance, complete with proper alignment, finishing and cleaning, complete in all respects as approved and directed by Engineer-in-Charge |
| 32 | M&L Vitreous China White Wash down Water Closet Pan (Wall mounted type) of approved make and quality, including integrated flushing arrangement , complete with white plastic seat cover, suitable heavy duty MS/Aluminium CP hanging brackets/support frame, necessary anchor fasteners, connection to soil pipe, proper alignment and leveling, cutting/chasing in wall where required, jointing and sealing with suitable compound to ensure leak-proof performance, and making good all disturbed surfaces to match existing finish, complete in all respects as approved and directed by Engineer-in-Charge. |
| 33 | Taking down and refixing of old vitreous china white wash down water closet (pedestal or wall mounted type) of any description, including disconnecting from flushing system and soil pipe, removing seat cover, fittings and accessories, stacking serviceable materials as directed and disposing unserviceable materials within lead as specified, including necessary fittings, realignment, jointing with cement mortar, sealing all joints to ensure leak-proof performance, making good all disturbed wall/floor surfaces to match existing finish, complete in all respects as approved and directed by Engineer-in-Charge. |
| 34 | S & F plastic water closet seat cover (closed pattern) of approved make, white colour, with flat bottom, complete with durable hinges of stainless steel/CP brass or aluminium, including removal of old seat cover if required, proper fixing, alignment and tightening, ensuring smooth operation, and making good minor damages, complete in all respects as approved and directed by Engineer-in-Charge. |
| 35 | S&F PVC flushing cistern of 10 litre capacity, low level type, syphonic action, complete with inlet ball valve, float, handle/lever arrangement and suitable flush pipe of 32mm dia, including necessary cutting, chasing and connection to water supply and W.C., testing for smooth operation and leakage, dismantling of unserviceable cistern if required, and making good disturbed surfaces with cement mortar to match existing finish, complete in all respects as approved and directed by Engineer-in-Charge |
| 36 | Taking down of old bibcock/Flush tanks/Mixers(any)/angle valves/shower/bottle trap or similar sanitary fittings of any type any description and make, including dismantling of the fitting, inspection and replacement of worn-out components such as washers, O-rings, cartridges, spindles, gland packing or seals, cleaning of internal parts, reassembly and refixing with PTFE tape and necessary fittings, ensuring proper alignment and complete stoppage of leakage,and minor making good of disturbed surfaces, complete as directed by Engineer-in-Charge |
| 37 | S&F in repairs Vitreous China wash hand basin 550 x 400mm Size (oval shape) of approved make , white colour, complete with 32mm dia CP brass waste fitting, including necessary cutting/chasing in wall, connection to water supply and waste pipe, proper alignment and leveling, dismantling of unserviceable , making good disturbed surfaces with cement mortar, and ensuring leak-proof installation, complete in all respects as approved and directed by Engineer-in-Charge |
| 38 | S&F in repair chromium plated bottle trap 32 mm bore for wash hand basin, with inlet and outlet suitable for connection to existing pipe system, including all necessary unions, nuts, washers and sealing materials, proper alignment, tightening and testing for leak-proof performance complete in all respects as approved and directed by Engineer-in-Charge. |
| 39 | M&L for replacement of 75mm outlet PVC(SWR) floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and directed by Engr-in-Charge |
| 40 | S&F in repair, 6mm thick glass corner shelf (12\\"x12\\") with C type Brass CP bracket, complete all as specified and directed by Engr in charge. |
| 41 | S&F high pressure flexible PVC connection pipe of 600mm length suitable for hot and cold water supply for 15mm dia connections, with braided reinforcement and heavy duty brass CP check nuts at both ends, including proper fitting to fixtures and pipeline, tightening, use of suitable washers/sealing materials, testing for leak-proof performance under working pressure, and minor adjustments as required, complete in all respects as approved and directed by Engineer-in-Charge |
| 42 | Dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar up to 110 mm dia complete all as specified and directed by Engr-in-Charge. |
| 43 | S&F in repair 110mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed by Engr-in-Charge. Note- Work to be carried out inside shaft from GF to 11th floor. |
| 44 | S&F in repair 75mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed by Engr-in-Charge. Note- Work to be carried out inside shaft from GF to 11th floor. |
| 45 | S&F in repair 32mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed by Engr-in-Charge. |
| 46 | S&F in repair 32mm dia PVC SWR Bend complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F in repair 75mm dia PVC SWR Bend complete all as specified and directed by Engr-in-Charge.Note- Work to be carried out inside shaft from GF to 11th floor. |
| 48 | S&F in repair 110mm dia PVC SWR Bend complete all as specified and directed by Engr-in-Charge. Note- Work to be carried out inside shaft from GF to 11th floor. |
| 49 | S&F in repair 75mm dia PVC SWR Junction Single (Tee) complete all as specified and directed by Engr-in-Charge. Note- Work to be carried out inside shaft from GF to 11th floor. |
| 50 | S&F in repair 110mm dia PVC SWR Junction Single (Tee) complete all as specified and directed by Engr-in-Charge. Note- Work to be carried out inside shaft from GF to 11th floor. |
| 51 | S&F in repair (HDPE) water storage LOFT Tank 200 Ltrs capacity in kitchen, hoisted and fixed in position all specified in MES Schedule Part-I, including tank nipple, union and lowering of unservicable Water Storage Tank including dismantling of old water tank complete all as specified and as directed by Engineer-in-Charge. |
| 52 | S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 15 mm bore complete all as specified and directed by Engineer in charge. |
| 53 | S&F 20 mm Bore gun metalGlobe/Gate valves with iron wheel/Lever half turn fixed-in-repairs complete all as specified and as directed by Engineer in charge. |
| 54 | S&F 25 mm Bore gun metalGlobe/Gate valves with iron wheel/Lever half turn fixed-in-repairs complete all as specified and as directed by Engineer in charge. |
| 55 | S&F 32 mm Bore gun metalGlobe/Gate valves with iron wheel/Lever half turn fixed-in-repairs complete all as specified and as directed by Engineer in charge. |
| 56 | S&F in repair 20 mm gun metal Pressure release valve with all fittings complete all as specified and as directed by Engineer in charge. |
| 57 | S&F for Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 15 mm bore and fixed as in repair complete all as specified and directed by Engineer-in-Charge. |
| 58 | M&L for providing and fixing 6 mm thick BWR grade plywood (BB or equivalent approved quality) in panels/walls/partitions, fixed with screws/nails to existing framework including dismantling/removal of old plywood of any description, making good of the surface, cutting to size, fitting and finishing complete; one side finished with decorative laminate/veneer of approved shade and design and the other side with primer and two coats of synthetic enamel paint, including all necessary adhesives, edge finishing, complete as directed by Engineer-in-Charge |
| 59 | Supply and Fixing in repairs, Looking Mirror selected quality of size 900 mm x 600 mm x 6 mm thick, having four holes on corners fixed to walls with CP Brass screws with fancy type head top complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F in repairs aluminum door seal fixed to bottom of door shutters complete all as specified by engr in charge |
| 61 | S&F in repairs toilet paper holder of stainless steel fixed to wall with CP brass screws complete all as specified and as directed by the Engineer in Charge. |
| 62 | S&F in repairs brass phase with washer including removing old unserviceable phase and fixing in old serviceable Taps ,angle cock Mixer Valve and Piller tape complete suitable for 15mm bore bib taps angle cock Piller tap/Mixer Valves and make leak proof all as specified and as directed. |
| 63 | S&F in repairs brass phase with washer including removing old unserviceable phase and fixing in old concealed stop cock complete suitable for 15mm bore concealed stop cock and make leak proof all as specified and as directed. |
| 64 | S & F of stainless steel kitchen sink with drain board made of minimum 0.8 mm to 1.0 mm thick SS (grade 304 as approved) of standard market size, including waste coupling, plug, washers and necessary fittings, fixing over platform or wall with CI/MS brackets or suitable supports, including cutting, fitting, sealing with plumber’s putty/silicone, connecting to waste pipe, testing for proper drainage, and dismantling/removal of existing sink (if any),and making good of surrounding surfaces, complete as directed by Engineer-in-Charge.. |
| 65 | S&F in repair, Stainless steel soap dish, complete all as specified and directed by Engr in charge. |
| 66 | S&F in repair grating round /circular with waste hole or without waste hole of dia 75mm/ 100mm size of stainless steel complete all as specified and as directed by the Engineer in Charge. |
| 67 | S&F of overhead shower of standard market size (150 mm to 200 mm dia or equivalent square size), made of brass/stainless steel/ABS with chromium plated finish, of approved make (Jaquar/CERA/GEM/Parryware or equivalent), including swivel joint/adjustable arm suitable for 15 mm bore connection, with uniform spray pattern, including dismantling/removal of existing unserviceable shower (if any), fixing with necessary fittings such as wall flange, PTFE tape, connectors, ensuring proper alignment and making good of disturbed surfaces, complete as directed by Engineer-in-Charge. |
| 68 | S&F in repair waste cupling fitting brass chromium plated of 32 mm dia for wash hand basin with long screwed sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. |
| 69 | S&F in repair waste cupling fitting 75/100 mm size for 40/32 mm dia waste pipe for SS sink with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. |
| 70 | Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. |
| 71 | M&L for 10 mm thick rendering in CM 1:3 on concrete/gunniting surfaces as in ceiling mixed with integral water proofing compound , the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.. |
| 72 | M&L for 15 mm thick rendering in CM 1:6 on brick/concrete surfaces of wall, mixed with integral water proofing compound, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 73 | M&L for preparation of newly plastered surfaces of ceiling by Vacuum based sanding machine complete all as specified, applying wall care putty upto 1mm thick as required (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured over a coat of approved primer by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 74 | M&L for preparation of newly plastered surfaces of walls by Vacuum based sanding machine complete all as specified & directed by Engineer-in-Charge. |
| 75 | M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by Vacuum based sanding machine, removal of nails etc & filling cracks/hole with putty, complete all as specified & directed by Engineer-in-Charge. |
| 76 | M&L for wall care putty upto 2mm thick as required (multi purpose mixer shall be used for uniform and proper mixing of putty) on wall surfaces complete all as specified & directed by Engineer-in-Charge. |
| 77 | M&L for priming plastered or unplastered surfaces of walls with alkiresistant priming paint by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 78 | M&L for two coats oil emulsion distemper white or coloured by auto roller on wall surfaces complete all as specified & directed by Engineer-in-Charge. |
| 79 | M&L for preparation of plastered or un plastered old decorated surfaces of walls by Vacuum based sanding machine all as specified, removal of nails etc & filling cracks/hole by applying wall care putty (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying one coat oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 80 | M&L for preparation of plastered or un plastered old decorated surfaces of ceiling by Vacuum based sanding machine all as specified, filling cracks/hole by applying wall care putty and applying one coat oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 81 | M&L for providing and applying URP 301, a polymer-based bonding and waterproofing agent, mixed with cement in specified ratio and applied in two coats over cleaned and pre-wetted concrete/masonry surfaces as per manufacturer’s specifications, including surface preparation and curing. Measurement shall be in square meters of finished treated surface. |
| 82 | M&L for providing and applying Pidilite Dr fixit Pidifin 2K/Pidilite Dr Fixit Fastflex/ Fosroc Brushbond which is two-component, acrylic polymer-modified cementitious waterproofing coating, in two coats over prepared concrete/masonry surface including surface cleaning, wetting, mixing as per manufacturer’s specification, and curing to ensure seamless waterproofing protection. |
| 83 | M&L for preparation of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 84 | M&L for preparation of old painted surfaces of steel & steel based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 85 | Supply and fixing of factory-made uPVC sliding windows of approved make in white or coloured finish, comprising three-track three-panel system (or as required) with two glazed shutters and one fly mesh shutter, made from multi-chambered uPVC profiles reinforced with GI steel inserts of minimum 1.2 mm to 1.6 mm thickness, including 5 mm thick clear glass (or as specified), stainless steel or fibre fly mesh, EPDM gaskets/wool pile, interlocks, glazing beads, rollers, handles, locks, stoppers and all necessary hardware, complete; including dismantling/removal of existing windows of any description, stacking/disposal of unserviceable material and making good of the surrounding surfaces, fixing of new frame with screws, fasteners and packing ensuring proper alignment and smooth operation, sealing of gaps between frame and wall with PU foam/backer rod and weatherproof silicone sealant, including all materials, labour, fabrication, transportation, cutting, wastage and installation at all heights, complete as directed by Engineer-in-Charge. |
| 86 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) upto. 2.50 Sqm each complete all as specified and directed by Engineer-in-Charge. |
| 87 | S & F 35 mm thick factory-made flush door shutters of BWP/BWR grade with high-density solid core (hardwood/blockboard type) bonded under pressure, having plywood facings on both sides and hardwood/PVC lipping on all edges, including provision of lock block, cutting, fitting, and fixing in position with necessary adjustments, sealing edges with waterproof sealant, and applying primer before finishing & applying two coat of synthetic enamel paint complete as per direction of Engineer-in-charge. |
| 88 | Repairing and refixing of existing door shutters of any type and size (up to approx. 2 sqm), including taking down the shutter, easing, planing/trimming (if required), realignment, tightening or replacement of screws, minor repairs to joints, and refixing in the same opening, ensuring smooth operation and proper clearance; including adjustment/refixing of existing hinges, handles and fittings, oiling/greasing of hardware, checking alignment with frame, and minor making good of disturbed surfaces,as directed by Engineer-in-Charge.. |
| 89 | Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each |
| 90 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 50x75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length , complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 91 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 92 | S&F PVC door frame of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid prelaminated PVC foam sheet mite cut at two corners and jointing with 2 Nos of 150mm long brackets of 15x15mm MS square tube of two vertical door profiles are to be reinforced with 19x19mm MS square tube of 19 guage WPDM rubber gasket weather seal tobe provided throughout frame the door frame shal be fixed to the wall using 100mm long MS screws through the frame by using PVC fastners. A minimum of 04 Nos screws to be provided for each vertical members and minimum 02 Nos of horizontal members. |
| 93 | S&F for 30mm thick factory made solid panel prelaminated PVC door shutter consisting of frame made out of MS tube of 19 guage thickness and size of 19x19mm for styes and 15x15mm for topo and bottom rails. MS frame shall have a coat of steel primer of approved make and manufacturer. MS frame adhered with 5mm thick heat moulded PVC `L' channel of size 30x75mm forming styles and 5mm thick, 100mm wide PVC sheet for top rail lock rail and bottom rail on either side and 5mm thick 20mm wide PVC sheet as gap inserted for top rail and bottom rail. panelling of 5mm PVC sheet to be fitted in MS frame to the styles and rails with 5mm thick 30mm wide PVC sheet beading on either side and jointed together with solvent cement adhesive etc Complete all as specified and as directed by Engineer- in- Charge. |
| 94 | S & F 18/19 mm thick exterior grade HDMR board as in Modular kitchen cupboared/almirah conforming to BWP grade with density not less than 700–750 kg/m³, finished with 1.0 mm thick laminate (mica) on external & internal surfaces, with 2 mm thick PVC edge banding on all exposed edges using hot press machine, complete carcass (box type) construction , including all necessary hardware fittings such as piaono hinges /stainless steel soft-close hinges, screws, as required ,including provision of minimum six (6) drawers with soft close channel and two (2) Stainless Steel cutlery tray /basket ,along with adequate shelves/compartment for storage of utensils and kitchen items and , including provision for cut-outs for sink, hob and services, sealing of all joints with silicone and sealing of all cut edges especially in wet areas with waterproof sealant, ensuring material is termite and borer resistant as per manufacturer specifications , complete with proper alignment, levelling and fixing using suitable wall anchors/fasteners to ensure rigidity,including dismantling and removal of existing particle board/wooden cabinets, shutters, frames, fittings. complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 95 | S&F prelaminated particle board 18 mm thickness, of approved make and finish, used for shutters, shelves, pelmets or similar works, with decorative surface on exposed face and balancing finish on the other side, including cutting, machine edge finishing/edge banding, grooving (if required), drilling and fixing with suitable screws, fittings and adhesives to existing or new framework, ensuring proper alignment and smooth finish; including removal of existing unserviceable board (if any) and minor making good as directed by Engineer-in-Charge. |
| 96 | S&F 2nd class hard wood plain fillets not exc 3 sqcm sectional area, square, rectangular or tringular in section, wrought fixed with nails complete all as specified and as directed by Engr in Charge. |
| 97 | S&F in repair, Magnet catch for fixing in cup board as approved by engr-in-Charge |
| 98 | S&F in repairs 25mm dia stainless steel curtain rods including SS brackets and decorative knob fitted at end complete all as specified and as directed by Engr-in-Charge |
| 99 | S&F contineous (piano) hinges, mild steel bright finish of 40 mm width of flaps(when open) complete all as specified. |
| 100 | S&F telescopic drawer channel 18\\" long complete all as specified and directed by Engineer-in-Charge. |
| 101 | S & F in repair rubber beeding to be fixed over glass panes in Aluminum widows complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 102 | Hacking out old broken glass (any th size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg.. |
| 103 | S&F Figured Glass pin head type 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 104 | S&F Sheet Glass ordinary 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 105 | S & F in repair of stainless steel wire mesh of minimum 0.35–0.40 mm wire thickness with aperture size approx. 1.2 mm to 1.5 mm, made of SS 304 grade or equivalent approved quality, fixed to existing/aluminium/wooden frames using aluminium/wooden/UPVC beading or rubber gasket system, including cutting to size, proper stretching, fixing with self-tapping screws/nails, finishing edges neatly complete all as specified and as directed. |
| 106 | S & F in repair of heavy-duty floor-mounted door stopper, made of aluminium/stainless steel/brass body with rubber buffer, size approx. 125 mm to 150 mm, with spring or magnetic mechanism (if required), fixed to floor using screws and rawl plugs, c complete all as specified and as directed by Engr-in-Charge |
| 107 | S&F in repairs 75 mm long,designer pattern Stanless Steel handles for fixing in cupboards all as directed and as specified by Engr-in Charge |
| 108 | S&F SS medium weight butt hinge ISI Marked 100mm size, fixed with screw complete all as specified and as directed. |
| 109 | S&F extruded anodised aluminum alloy handle 150mm long fabricated type |
| 110 | S&F anodised aluminum barrel tower bolt of extruded section 150mm long |
| 111 | M&L fabricated frame work as in doors of gate of angle iron or other section with gusset plate rails, braces etc. complete drilled for fixing steel sheeting or other covering door etc to be prepared for hanging with and including hinges .complete all as specified and directed by Engineer-in-Charge. Note: Work has to be carried out in (G+10) Storey bldg. |
| 112 | Dismantling structural steel work incl. steel door,gate,window guard bars,grills etc.complete all as specified and directed by Engineer-in-Charge. |
| 113 | M&L for mild steel works as in grills and railing of Fe-410-0or Fe 310-0,complete all as specified and directed by Engineer-in-Charge. |
| 114 | Removal, collection, loading, transportation and disposal of debris/malwa from each and every building, shafts, common areas and all connected/approach area, including lifting from scattered locations, stacking, loading into tractor trolley, conveying and unloading at approved dumping site for all leads up to 10 km , each trolley shall be of minimum size 3.0 m × 1.5 m × 0.90 m (L × B × H) or equivalent complete cleaning of site and making good of disturbed surfaces.complete all as specified and as directed by Engr-in-charge Note: No Lifts shall be use for transportation of materials in Buildings. |
| 115 | Note :- (i) The amount of Rs 136122.00 against Schedule of Credit on Srl Page 146 shall be deducted from the total amount quoted against Sch 'A' (ii) No Lift will be used by the contractor for mobilization of material, T&P and debris. Please Enable Macros to View BoQ information |
