|
| 1 | CIVIL WORK CIRCULAR MAIN GATE |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: All kinds of soil |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stoneaggregate 40 mm nominal size derived from natural sources) |
| 4 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources |
| 5 | Centering shuttering including struttings, propping etc. and removal of form work for Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 6 | Steel reinforcement for R.C.C. work ready to use “cut and bend” rebars of approved make from factory/workshop to construction site including placing in position and binding all complete upto plinth level. 5.22B.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 7 | 15 mm cement plaster of mix in 1:2 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall. |
| 8 | Finishing walls with Acrylic Smooth exterior paint of required shade :13.46.1 New work (Two or more coat applied @ 1.67 |
| 9 | CIVIL WORK BOUNDRY WALL & FOOTPATH |
| 10 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge:All kinds of soil |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stoneaggregate 40 mm nominal size derived from natural sources) |
| 12 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 13 | Centering shuttering including struttings, propping etc. and removal of form work for Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 14 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.C.C. Work Using Cold Twisted Bars |
| 15 | 15 mm cement plaster of mix in 1:2 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall |
| 16 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 17 | Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. 7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 18 | Laying RUBBER SURFACE COATED interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer in-charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 19 | Finishing walls with Acrylic Smooth exterior paint of required shade :13.46.1 New work (Two or more coat applied @ 1.67 |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint ofapproved brand and manufacture |
| 21 | Landscaping |
| 22 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: 2.1.1 All kinds of soil |
| 23 | Extra for levelling & neatly dressing of disposed soil completely as directed by Engineerin-charge |
| 24 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. |
| 25 | Grassing with doob grass including watering and maintenance of lawn for 30 days or more till grass forms a thick lawn free from weeds and fit for mowing including supplying good earth as needed in rows 7.5 cm. apart in either direction. (cost of good earth if needed to be paid for seperately) |
| 26 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). |
| 27 | 2.25 Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment |
| 28 | Preperation of beds of 0.45 m width for hedging and shrubbery by excavating 60 cm deep and refilling the excavated earth after breaking clods and mixing with manure in ratio 8:1 (8 parts of excavated earth : 1 part of stacked volume of well rotten cow dung manure after reduction by 8%). flooding with water and filling with earth if necessary, watering and finally fine dressing, levelling etc including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed within a lead of 50 m and lift up to 1.5 m complete (cost of cow dung manure and extra imported earth to be paid seperately). |
| 29 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) 2.14.1 Holes 1.2 m dia and 1.2 m deep |
| 30 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) 2.57.2 Shrubs Plant |
| 31 | Trees/ Exotic Plants: Supply and plantation of plants as per sample approved by the engineer. Plants should be quite healthy, disease free as per ht. & specification given below. Species can be changed as per site requirement and as per directions of engineer. |
| 32 | 10282 Ficus benjamina (green) height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bag |
| 33 | Ficus Retusa Topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot |
| 34 | 10200 Ficus black vivion piller Topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot |
| 35 | 5.20 Providing and Displaying Ficus black vivion piller topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 36 | Plumeria alba height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bag |
| 37 | Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge. |
| 38 | 10320 Pinus longifolia (Pinus) height 90-105 cm. in cement pot size 35 cm |
| 39 | Providing and stacking of Ficus reginald well branched, bushy of height 60- 75 cm. in earthen pots of size 25 cm as per direction of theofficer-in-charge. |
| 40 | Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. plant in 25 cm size Earthen Pot/ Plastic Pot |
| 41 | 10128 Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot. |
| 42 | Topiary plant of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht. plant, in 35 cm Cement Tray /Cement Pot |
| 43 | Araucaria cookie having ht.1.80 m to 1.95 m, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 30 cm size of Earthen pot / Plastic pot. |
| 44 | Plumeria alba height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bag |
| 45 | Plumeria alba height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bag |
| 46 | Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of theofficer-in-charge. |
| 47 | Bottle palm ht. 150-180 cm bottom girth 20-25 cm well developed in bigpoly bag size 25 cm |
| 48 | Cycus revoluta in 35 cm challi, specimen plant, having 30 to 40 with fresh and healthy, leaves having 25cm to 30cm circumfrance of base stem well developed |
| 49 | Fishtail palm well developed with fresh & healthy foliage leaves of ht 210 to 240cm Specimen plant in 35 cm Cement Pot |
| 50 | Phoenix Palm having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot |
| 51 | Rhapis Palm having ht. 45 cm to 60 cm with 5 to 7 suckers, well developed, full of fresh and healthy leaves in 25 cm size of Earthen pot / Plastic pot. |
| 52 | Providing and Displaying Ficus black vivion piller topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 53 | Providing and Displaying Golden Bottle brush Topiary well developed with fresh & healthy foliage 5 to 6 big ball 115 to 180 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge |
| 54 | Money Plant Broad Leaves mounted on moss stick 90 cm ht., 3 to 4plants in each pot, well developed with full of fresh & healthy leaves in size of 25 cm Top dia x 18 cm Bottom dia x 25 cm Perpendicular height Earthen pot / Plastic pot.. |
| 55 | Providing and displaying of Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of Bucket type cement pots & as per direction of the officer-in-charge. |
| 56 | Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 57 | Assorted Creepers |
| 58 | Providing and stacking of Petra volubilis of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of theofficer-in-charge. |
| 59 | Providing & fixing of White River (Stone) Pebbles size of 2\\" to 2.50\\" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. |
| 60 | Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. 2.29.1 Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm |
| 61 | Providing and Fixing, Pergola including Fabricating, welding and applying primer with MS Pipes and MS angles and fixing CC 1:2:4 foundation to required depth etc complete as directed by the engineer incharge. |
| 62 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 63 | 25 mm dia nominal bore |
| 64 | Informative Signage |
| 65 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: 2.1.1 All kinds of soil |
| 66 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stoneaggregate 40 mm nominal size derived from natural sources) |
| 67 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 68 | Centering shuttering including struttings, propping etc. and removal of form work for Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 69 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.C.C. Work Using Cold Twisted Bars |
| 70 | Random rubble masonry with hard stone in foundation and plinth including levellingup with cement concrete 1:6:12 (1 cement: 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 71 | Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 72 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick |
| 73 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 9.1.1 Second class teak wood |
| 74 | Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface. 8.25.1 40 mm thick |
| 75 | Providing and fixing sloping chajja of stone 40 mm thick and upto 80 cm wide beyond the wall as measured along the slope in cement mortar 1:4 (1 cement : 4 coarse sand) with 12 mm diameter anchoring steel bar, 45 cm long, fixed in each stone and supported on and including with bricks cove in cement mortar 1:4 (1 cement : 4 coarse sand), including pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.28.1 Red sand stone : |
| 76 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 8.2.2.1 Area of slab upto 0.50 sqm |
| 77 | Engraving letters in hard stone |
| 78 | Toilet civil work |
| 79 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: All kinds of soil |
| 80 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stoneaggregate 40 mm nominal size derived from natural sources) |
| 81 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 82 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 83 | Centering shuttering including struttings, propping etc. and removal of form work for Lintels, beams, plinth beams, girders, bressumers and cantilevers. 4.3.3 Columns, piers, abutments, pillars, posts and struts |
| 84 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stoneaggregate 20 mm nominal size derived from natural sources) |
| 85 | Centring and Shuttering for Suspended floors, roofs, landings, balconies and access platform. 4.3.3 Columns, piers, abutments, pillars, posts and struts |
| 86 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.C.C. Work Using Cold Twisted Bars |
| 87 | Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : 6.3.1 With F.P.S.(non modular) bricks |
| 88 | 15 mm cement plaster of mix in 1:2 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall |
| 89 | 11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 90 | 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg |
| 91 | Providing and fixing to existing door frames. 9.118.1 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 92 | 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 93 | Internal Plumbing & Saniitary(Toilet) |
| 94 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 95 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required: 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 96 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 97 | Providing and fixing soil, waste and vent pipes : 17.35.1 100 mm dia17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 |
| 98 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 99 | 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 100 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 101 | Providing and fixing terminal guard : 17.56.1 100 mm17.56.1.1 Sand cast iron S&S as per IS - 1729 |
| 102 | Providing and fixing uplasticised PVC connection pipe with brass unions : 18.21.1 30 cm length 18.21.1.1 15 mm nominal bore |
| 103 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe 17.28.1.1 32 mm dia |
| 104 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : 17.25.1 Flat back wash basin of size 630x450 mm |
| 105 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I.trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 106 | Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : 22.2.1 Using rough Kota stone |
| 107 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction ofEngineer -in-charge. 23.3.1 100 mm nominal size dia |
| 108 | 18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 109 | WATER SUPPLY |
| 110 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 18.10.2 20 mm dia nominal bore |
| 111 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 112 | 20 mm dia nominal bore |
| 113 | 25 mm dia nominal bore |
| 114 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. |
| 115 | 32 mm nominal bore., |
| 116 | Providing and fixing brass bib cock of approved quality : 18.15.1 15 mm nominal bore |
| 117 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 18.17.1 25 mm nominal bore |
| 118 | 20mm nominal bore |
| 119 | 25 mm nominal bore |
| 120 | 32 mm nominal bore |
| 121 | 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 122 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm` |
| 123 | Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 18.20.3 25 mm nominal bore |
| 124 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.18.51.1 15 mm nominal bore |
| 125 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 18.53.1 15mm nominal bore |
| 126 | External Plumbing and Sanitary |
| 127 | WATER SUPPLY |
| 128 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore |
| 129 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 130 | 20 mm dia nominal bore |
| 131 | 25 mm dia nominal bore |
| 132 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore |
| 133 | 32 mm nominal bore., |
| 134 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore |
| 135 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 136 | 20mm nominal bore |
| 137 | 25 mm nominal bore |
| 138 | 32 mm nominal bore |
| 139 | 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 140 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore |
| 141 | Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore |
| 142 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 143 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore |
| 144 | Septic Tank AND SOAK PIT |
| 145 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil. |
| 146 | P.C.C. 1:4:8 in Foundation |
| 147 | Brick work in C.M. 1.4 in foundation |
| 148 | P/L C.C. flooring 52mm thick with C.C. of 1:2:4 |
| 149 | P/L R.C.C 1:1½:3 in foundation |
| 150 | Centering & Shuttering work |
| 151 | Reinforcement for RCC work |
| 152 | 20mm tk Cement Plaster in C.M. 1 : 4 |
| 153 | P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions |
| 154 | Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar |
| 155 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 156 | Under Ground Tank |
| 157 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil. |
| 158 | P/L C.C. of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 159 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level |
| 160 | Centering and shuttering i/c strutting, propping etc. and removal of form for : |
| 161 | Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12 mm thick |
| 162 | Lintels, beams, plinth beams, girders, and cantilevers |
| 163 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars |
| 164 | 12mm C.P. finished with a floating coat of neat cement in cement mortar 1:4( 1 cement : 4 fine sand) |
| 165 | Internal plaster of tank |
| 166 | P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions |
| 167 | Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar |
| 168 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. |
| 169 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 170 | Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : |
| 171 | Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough kota stone. |
| 172 | MISC. ITEMS |
| 173 | Making and installation FRP Sculptures playing dhol, damau or ransingha depicting uttarakhand’s traditional theme of height 6ft they will be made in Clay first by a moulding artist and after obtaining FRP pieces they all are jointed together in one piece after creating a MS frame of the entire sculpture then further sealed and locked in with bolts and Resin coating. Paint and PU coating to be done at last for longevity of the paint and durability against all weather and conditions. We will charge @ |
| 174 | Topiary animal in FRP with grass wrapping and Ms pipe framework inside. It will be made in clay first by clay moulding artist after which dye will be taken of it then further FRP piece will be casted which will further be sanded down to perfect and wrapped with high quality grass finish wrap accordingly. Size – 8FT. We will charge @ |
| 175 | Making and installation of ‘Wing’s Selfie Point’ in FRP. Wings will be made in clay first by a clay moulding artist after which dye will casted and entire piece will be taken out then further sanding and finishing will be done after which iron MS structure will be installed inside with painting and PU to be done at last. We will charge @ |
| 176 | Supplying and fixing of FRP made animal dustbins. We will charge @ |
| 177 | Sitting benches in FRP material looks like wooden log with deco colour and PU coating to protect the colour for longer period. Size: 18”x18”x42”. We will charge @ |
| 178 | Making and installation of FRP gazebo, it features a traditional Uttarakhand hills architecture theme with a modern twist in FRP material. The structure is made of durable MS (mild steel) framework, providing stability and strength. The decorative pillars are crafted from FRP, adding an elegant touch. The roof is designed with the Pathal stone in FRP features intricate carvings, blending seamlessly with the natural surroundings. The gazebo design captures the essence of Uttarakhand’s rich cultural heritage, making it a perfect addition to any hill station or garden. Size of gazebo: 10ft x 14ft along with platform, Size of platform: 9ft X 9ft X 1ft with stone tiles |
| 179 | The Geyser Fountain will be constructed and installed within a 20 ft x 6 ft pond area, which will be finished with high-quality waterproof mosaic tiles to provide a reflective and visually appealing base. Strategically positioned water nozzles will be installed to create customizable and visually captivating water patterns. Waterproof LED lighting will be integrated to illuminate the fountain, enhancing the aesthetic effect with a magical glow that interacts with the tile surface. A submersible pump system will be fitted to ensure efficient and continuous water circulation. The installation will also include a robust drainage system to allow for easy water management and maintenance. All components, including lighting and the pump, will be connected to a suitable and secure power supply. The entire process—from material sourcing and system setup to testing and commissioning—will be carried out with precision to deliver a fully functional and visually striking fountain feature suitable for indoor or outdoor settings. We will charge @ |
| 180 | MISC. ITEMS |
| 181 | Providing & fixing PHILIPS solar LED street light 15 W complete with all vis pannel, battery,pole with three day autonomy as per enclosed specification. |
| 182 | Indoor and Outdoor Electrical |
| 183 | Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-C |
| 184 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed mediumclass PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 185 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 186 | 20 mm |
| 187 | 25 mm |
| 188 | Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 8Way (4+24), Double door |
| 189 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and neutral |
| 190 | Single pole |
| 191 | Single pole and neutral |
| 192 | Triple pole and neutral |
| 193 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 194 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 195 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 196 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 197 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 198 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 199 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. |
| 200 | Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 201 | 3.5x95 |
| 202 | 3.5x150 |
| 203 | Supplying and Fixing 4A to 32A rating 240/415V 10KA \\"C\\" Curve minature circuit braker suitable for inductiva ;oad for following poles in the existing MCB DB complete with connection, testing and commissioning etc as required Tripple pole and Neutral |
| 204 | Tripple pole and Neutral |
| 205 | B GARDENLIGHTING WORK |
| 206 | Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 8Way (4+24), Double door |
| 207 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 208 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 209 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 210 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 211 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 212 | Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. Please Enable Macros to View BoQ information |
