|
| 1 | Demolition of plain cement concrete of any description and in any position (below and above ground level ) not otherwise specifically provided for complete all as specified and as directed. |
| 2 | Demolition of brick work/ stone masonary built in cment mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 3 | Demolition of reinforced cement concrete of any description and in any position (below and above ground level ) not otherwise specifically provided for including reinforcement cut to required size to facilitate demolition complete all as specified and as directed. |
| 4 | Material & labour for cement concrete in foundations, filling and mass concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and as directed. |
| 5 | Use and waste type of formwork to sides of walls of RCC drain and similar works for rough finished flat surface of drain complete all as specified and as directed. |
| 6 | Use and waste type of formwork to sides of walls of RCC drain and similar works for fair finish surface of drain complete all as specified and as directed. |
| 7 | Formwork to edges of concrete flats,floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat surface complete all as specified and as directed. |
| 8 | Material and labour for RCC drain bottom slab / basement slab or even in top slab using cement concrete M-25 (design mix) using 20mm graded stone aggregate in position complete all as specified and as directed. |
| 9 | Material and labour for RCC retaining wall / drain side wall using reinforced cement concrete M-25 (design mix) using 20mm graded stone aggregate in position complete all as specified and as directed. |
| 10 | Material & labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 11 | Ditto as per item No 10.00 above above but 6mm to 8mm dia complete all as specified and as directed. |
| 12 | Material & labour for brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean redius built in cement mortar 1:4 complete all as specified and directed. |
| 13 | Material & labour for uncoursed random rubble masonary built in cement mortar 1:4 complete all as specified and as directed. |
| 14 | Ditto as above item No 13.00 but except stone complete all as specified and as directed. |
| 15 | Material & labour for plain cement concrete in copping and haunching in drain and any other pcc course type C-1 1:3:6 type C-1 using 20mm graded stone aggregatecomplete all as specified and as directed. |
| 16 | Material & labour for extra for forming fair finished drain or channel 30 cm inner not exceeding girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.complete all as specified and as directed. |
| 17 | Ditto as above sr item No 16.00 but for inner girth not exceeding 55cm complete all as specified and as directed. |
| 18 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed. |
| 19 | Racking out joints/ pointing of cement / cement lime mortar to uncoursed randoom rubble masonary complete all as specified and as directed. |
| 20 | Material & labour for 15mm thick rendering on fair finished surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed. |
| 21 | Material & labour for keyed pointing g to random or polygonal rubble, uncoursed or brought upto course in cement mortar 1:4 complete all as specified and as directed . |
| 22 | M & L for preparing new plastered surface of wall and applying two coats of cement base paint over and including a coat of alkali resistant primer complete all as specified and as directed. |
| 23 | Dismantling posts or struts steel or R.C.C any section, including taking out embedded portion and making good disturbed ground for embedment of new fencing post complete all as specified and as directed. |
| 24 | Supply & fixing mild steel angle iron posts and struts in fencing, steel gate frame including handmade hinges etc. including cutting top to shape as directed drilling holes welding and notching for wire etc and flat iron fillets for securing wire mesh including bedding or riveting etc conforming to Fe-290 Gde E-165, complete all as specified and directed. |
| 25 | Dismantling fencing wire mesh, any type complete all as specified and as directed. |
| 26 | Fixing only Chain link fencing including line wires, any mesh, size and type to any type of standerd, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed. |
| 27 | Supply only chain link MS galvanised fencing of mesh size 100 mm x 100 mm , complete all as specified and directed. |
| 28 | Supply & fixing mild steel screw bolts ( machine made) with hexagonal heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washer and one hexagonal or square nut not exc 5cm and dia of shank 11 to 15mm complete all as specified and directed. |
| 29 | Material & labour preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed. |
| 30 | Material & labour two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description n.exc 10cm in width or girth not otherwise described including preparation of surfaces all as specified and directed. |
| 31 | Supply & fixing in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed |
| 32 | Dismantling wrought mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 33 | Supply & fixing mild steel Framed work suck as grills, gratings, guard bar etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars complete all as specified and as directed. |
| 34 | Material and labour for 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed. |
| 35 | Supply & fixing rubber moulded decorative designed coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 36 | Material and labour for sand filling under floor or in foundation including watering and consolidation completed all as specified (Note:- Sand cushion layer consolidated thickness is 20 mm below precast interlocking paver block complete all as specified and directed. |
| 37 | M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement complete all as specified and directed |
| 38 | Use of forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' in plinth protection complete all as specified and directed |
| 39 | M&L for Enddura Non Skid joint free colour tiles 8 to 10 mm thick (square/ rectangular) area of each tiles not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding screed bed 15cm in CM (1:6) complete all as specified and directed. |
| 40 | M & L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors including screed bed 15 mm thick in CM 1:6, complete all as spd & directed by Eng-in-charge |
| 41 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engineer-in-Charge |
| 42 | Material and Labour for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed by Engnr-in-Charge |
| 43 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortar etc complete all as specified and directed |
| 44 | M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite |
| 45 | M&L for Granite tiles 20mm thick (approved color and texture) machine cut, bedded including 20mm thick screed bed CM 1:6 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete |
| 46 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations Please Enable Macros to View BoQ information |
