|
| 1 | Schedule-A |
| 2 | S & F 18/19 mm thick exterior grade HDMR board as in Modular kitchen cupboared/almirah conforming to BWP grade with density not less than 700–750 kg/m³, finished with 1.0 mm thick laminate (mica) on external & internal surfaces, with 2 mm thick PVC edge banding on all exposed edges using hot press machine, complete carcass (box type) construction , including all necessary hardware fittings such as piaono hinges /stainless steel soft-close hinges, screws, as required ,including provision of minimum six (6) drawers with soft close channel and two (2) Stainless Steel cutlery tray /basket ,along with adequate shelves/compartment for storage of utensils and kitchen items and , including provision for cut-outs for sink, hob and services, sealing of all joints with silicone and sealing of all cut edges especially in wet areas with waterproof sealant, ensuring material is termite and borer resistant as per manufacturer specifications , complete with proper alignment, levelling and fixing using suitable wall anchors/fasteners to ensure rigidity,including dismantling and removal of existing particle board/wooden cabinets, shutters, frames, fittings. complete all as specified and directed by Engineer-in-Charge. |
| 3 | S&F in repair 18/19 mm thick prelaminated particle board exterior gde prelaminated one side with decorative choice and other side white lamination fixed with screws as in cup board shutters & shelves and pelmet boxes etc complete all as specified and directed by Engineer-in-Charge.Storey bldg. |
| 4 | S&F in repairs 100 mm long,designer pattern Stanless Steel handles for fixing in cupboards complete all as specified and directed by Engineer-in-Charge. |
| 5 | S&F in repair, Magnet catch for fixing in cup board complete all as specified and directed by Engineer-in-Charge. |
| 6 | S&F in repairs telescopic drawer channel 18\\" long complete all as specified and directed by Engineer-in-Charge. |
| 7 | S&F in repair, Hollow PVC Wall Lining consisting of 05 to 10 mm thick Plain colour PVC sheet inclusive of solvent cement & fixing on wall surface L & U channel , complete all as specified and as directed by Engineer- in- Charge.. |
| 8 | S&F contineous (piano) hinges, mild steel bright finish of 40 mm width of flaps(when open) complete all as specified and directed by Engineer-in-Charge. |
| 9 | S&F in repairs Wall Mixer for kitchen sink 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing complete all as specified and directed by Engineer-in-Charge. |
| 10 | S&F in repairs Brass CP fancy type Bib Cock 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed by Engineer-in-Charge. |
| 11 | S&F in repairs Angle Stop Cock 15mm Bore (dia), fancy type,Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 12 | S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1040 x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge. |
| 13 | S&F in repair,Stainless steel Plate rack of size 24\\"x36\\"x10\\"(all dimensions in inches) complete all as specified and directed by Engr in charge |
| 14 | S&F in repair waste cupling fitting 75/100 mm size for 40/32 mm dia waste pipe for SS sink with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. . |
| 15 | Demolition of cement concrete (Reinforcment) of any description all as specified & directed. by Engineer in Charge. |
| 16 | M&L for RCC in 1:2:4 type B-1(using 20 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work all as spd etc all as specified and as directed by Engineer in Charge. |
| 17 | Use and waste of formwork to slab , chajjas,slab, weather shades, corbels, water troughs and similar items including edges rough finished surfaces of concrete complete all as specified and directed by Engr-in-charge. |
| 18 | M&L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specifed and directed by Engr-in-Charge. |
| 19 | -ditto- as per item No -17 above 6 to 8mm dia complete all as specified and directed by Engr-in-charge. |
| 20 | M&L for 18 to 20mm thick pre polished granite (any colour) slab laid with 15 mm thick CM 1:4 bedding in door Chowkhat/Frame, Window Cill, plateform etc in floor and skirting/dado surface and jointed with grey cement slurry and pointed in white cement with pigment to match the shade of granite stone including Moulding/rounding and polishing & dismantling of the old stone and tiles of any description or thickness complete all as specified and directed by Engineer-in-Charge. |
| 21 | M&L for Ceramic coloured/ printed non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.11 Sqm but n. exec. 0.18 Sqm laid as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement sand mortar ( 1:4) and pointed with coloured cement to match with surfaces of tiles & including Dismantling of old Ceramic coloured/ printed non-skid tiles of any thickness including cement morter bedding (but not backing), removing serviceable tiles to the stores and rubbish off the premises.complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L Glazed Ceramic Coloured Tiles, 450x350x7mm thick, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick screed bed in cement mortar 1:4 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, & including Dismantling of old Ceramic coloured/ printed non-skid tiles of any thickness including cement morter bedding (but not backing), removing serviceable tiles to the stores and rubbish off the premises.complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mena radius built in cement mortar 1:4 including Demolition of brick work or stone/boulders masonry, built in cement mortar or cement lime mortar, complete all as specified and directed by Engineer-in-Charge. |
| 24 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each complete all as specified and directed by Engineer-in-Charge. |
| 25 | All as per Above Item No 23 but exceeding 1.50 sqm each and n.exc. 4 Sqm each complete all as specified and directed by Engineer-in-Charge. |
| 26 | Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each , complete all as specified and directed by Engineer-in-Charge. |
| 27 | S&F 35 mm thick factory made flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both the faces.complete all as specified and directed by Engineer-in-Charge. |
| 28 | Taking Down factory made flush shutters exc 1 sqm and n exc 2 sqm each including ,easing and adjusting and refixing in same opening/wooden frame/steel frame complete all as specified and directed by Engineer-in-Charge. |
| 29 | Taking Down wire Gauged Shutter exc 1 sqm and n exc 2 sqm each ,easing and adjusting and refixing in same opening repairing, tightening of hinges or changing the position of hinges adjustment of tower bolts sliding bolt etc, replacement of fittings and refixing on the same opening complete all as specified and directed by Engr-in-Charge. (Note:- New hinges, if required will be measured and paid under separate item). |
| 30 | S&F in repair Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. |
| 31 | S&F in repair Anodised aluminium window and ventilator shutters, side hung type or sliding without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Engineer-in-Charge. |
| 32 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing mentioned in SSR, complete all as specified and directed by Engr-in-charge. |
| 33 | S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail paneling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings and complete all as specified and directed by Engr-in-charge. |
| 34 | Dismantling structural steel work incl. steel door,gate,window guard bars,grills etc.complete all as specified and directed by Engineer-in-Charge. |
| 35 | M&L fabricated frame work as in doors of gate of angle iron or other section with gusset plate rails, braces etc. complete drilled for fixing steel sheeting or other covering door etc to be prepared for hanging with and including hinges .complete all as specified and directed by Engineer-in-Charge. |
| 36 | Taking down old Aluminum windows of any description size not exc. 2.50 sqm and M&L for complete overhauling of the glass pane/rubber beeding/aluminum glazing clip if necessary/locking system incl.necessary roiling and adjustment etc and refixing in same location complete all as specified and directed by Engineer-in-Charge. Note :- Glass Pane /rubber beading/ aluminum beeding will be measured and paid separately under subsequent items. |
| 37 | S & F in repair rubber beading to be fixed over glass panes in Aluminum widows complete all as specified and directed by Engineer-in-Charge. |
| 38 | S&F in repair, aluminum anodised glazing clip to the alumiinum window frames after fixing the glass panes complete all as specified and directed by Engineer-in-Charge. |
| 39 | M&L PCC for 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching & for fixing railing, holdfast etc complete all as specified and directed by Engineer-in-Charge. |
| 40 | Hacking out old broken glass (any size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as specified and directed by Engineer-in-Charge. |
| 41 | S&F Figured Glass pin head type 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F Sheet Glass ordinary 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete all as specified and directed by Engineer-in-Charge. |
| 43 | S&F in repair for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apoerture 1.40mm and fixed with aluminium/wooden/steel beads complete all as specified and directed by Engineer-in-Charge. |
| 44 | S&F in repars MS/SS medium weight cold rolled butt hinge ISI Marked 100mm size, fixed with screw complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F in repairs, MS Helical door spring 300 mm long complete all as specified and directed by Engineer-in-Charge.(Helical spring will be fixed by welding) |
| 46 | S&F butt hinge stainless steel 100/150mm size , fixed with stainless steel screw complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F in repais extruded anodised aluminum alloy handle 150mm long fabricated type , complete all as specified and directed by Engineer-in-Charge. |
| 48 | S&F anodised aluminum barrel tower bolt of extruded section 150mm long, complete all as specified and directed by Engineer-in-Charge. |
| 49 | S&F in repars aluminum alloy sliding door bolt 300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast of exctruded sections and fiing bolts or extruded section complete all as specified and directed by Engineer-in-Charge. |
| 50 | S&F Mild steel tower bolts,enamelled black,with bright bolt and fixed 150mm fixed. |
| 51 | S&F 125 mm long mild steel handles, cast type polished bright. |
| 52 | S&F S S mild steel sliding door bolt 300 mm longth with sand die cast brass hasp staple bolt type and fixing bolt complete all as specified and directed. |
| 53 | S & F in repair floor door stopper of size 140 mm long aluminium alloy body and tongue, anodized with hard drawn steel spring incl cleats etc fixed to door.complete all as specified and directed by Engineer-in-Charge. |
| 54 | S&F in repairs 25mm dia stainless steel curtain rods including cutting and fixing complete all as specified and directed by Engineer-in-Charge. |
| 55 | S& F in repairs Stainless Steel wall bracket suitable for 25mm dia curtain rods, complete all as specified and directed by Engineer-in-Charge. |
| 56 | S& F in repairs Stainless Steel designer pattern side knobs suitable for 25mm dia curtain rods complete all as specified and directed by Engineer-in-Charge. |
| 57 | M&L preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 58 | M&L preparation of new or previously steel surfaces of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primercomplete all as specified and directed by Engineer-in-Charge. |
| 59 | S&F in repairs aluminum door seal fixed to bottom of door shutters complete all as specified and directed by Engineer-in-Charge. |
| 60 | Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s),complete all as specified and directed by Engineer-in-Charge. |
| 61 | M&L for 10 mm thick rendering in CM 1:3 on concrete/gunniting surfaces as in ceiling mixed with integral water proofing compound , the surface shall be cured and allow to dry, finished even and smooth without using extra cement newly plastered surfaces of ceiling by Vacuum based sanding machine complete all as specified, applying wall care putty 2mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured including primer by auto roller complete all as specified and directed by Engineer-in-Charge. complete all as specified and directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.. |
| 62 | M&L for 15 mm thick rendering in CM 1:6 on brick/concrete surfaces of wall, mixed with integral water proofing compound, the surface shall be cured and allow to dry, finished even and smooth without using extra cement preparation of newly plastered surfaces of walls by Vacuum based sanding machine complete all as specified, applying wall care putty min 2mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured including primer by auto roller complete complete all as specified and directed by Engineer-in-Charge. including complete all as specified and directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately. |
| 63 | M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 using WPC 2% of weight of cement and finishing even and smooth without using extra cement including ,newly plastered surface of wall and applying two coat of cement base paint over a coat of primer on walls complete all as specified and as directed Note: Work has to be carried out in (G+10) Storey bldg..by Engineer-In-Charge.complete all as specified and directed. (WPC measured and paid saperatly). |
| 64 | Supply only integral water proofing compound. |
| 65 | Material and labour PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in hold fast block, roof kerbs or mud stop, coping, rounded or chamfered on edges and like including weathering, slightly rounded or chamfered angles and throating etc incuding necessary form work complete all as specified. |
| 66 | M&L for preparation of old painted surfaces of steel & steel based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 67 | S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situ-ation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc., complete all as specified and directed by Engineer-in-Charge. |
| 68 | S&F High pressure PVC connections pipe 600mm long suitable for Hot and Cold water for 15mm size with Brass CP Check nutcomplete all as specified and directed by Engineer-in-Charge. |
| 69 | S&F in repair (HDPE) water storage LOFT Tank 200 Ltrs capacity in kitchen, hoisted and fixed in position all specified in MES Schedule Part-I, including tank nipple, union and lowering of unservicable Water Storage Tank including dismantling of old water tank complete all as specified and directed by Engineer-in-Charge. |
| 70 | S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 15 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F in repairs 15 mm dia stainless steel curtain rods including wall bracket suitable for 15mm dia curtain rodscutting and fixing complete all as specified and directed by Engineer-in-Charge. |
| 72 | M&L for replacement of 75mm outlet PVC(SWR) floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and directed by Engineer-in-Charge. |
| 73 | Removal , collection,loading transportation and disposal of debris/malwa from each and every building, shafts,common areas and all connected/approach area,includig lifting from scattered locations, stacking, loading into tractor trolley shall be of minimum size 3.0 m x 1.5 m x 0.90 m (LXBXH) or distance exc 5 Km but n exc 10 Km and deposited out side the MD land. Note :- Searching of Place of Disposal out side the MD Land will be the responsibility of Contractor and rate of any distance shall be included in quoted unit rate. |
| 74 | Note :- (i) The amount of Rs 130450.00 against Schedule of Credit on Srl Page 146 shall be deducted from the total amount quoted against Sch 'A' (ii) Work has to be carried out in (G+10) Storey buildings. Please Enable Macros to View BoQ information |
