|
| 1 | Schedule-A |
| 2 | Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing the same from Site(s),complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L for 100mm thick PCC 1:3:6 Type C-2 (40mm Graded Stone Aggregate) as in sub floor, sub bases, floors,roof etc.,omplete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for 75mm thick PCC 1:2:4 Type B-1 (20mm Graded Stone Aggregate) as in sub floor, sub bases, floors,roof etc. complete all as specified and directed by Engineer-in-Charge. |
| 5 | S & F vitrified tiles tiles light shade 10mm thick (square/rectangular) polished, area of each tile n.exc. 0.36 sqm, in floor etc.,set and jointed in neat cement slurry over & including 15mm thick screed bed in CM 1:6 and pointed in white or coloured cement with pigment to match for laying floor fineshes & including Dismantling of old Ceramic coloured/ printed non-skid tiles of any thickness including cement morter bedding (but not backing), removing serviceable tiles to the stores and rubbish off the premises.complete all as specified and directed by Engineer-in-Charge. |
| 6 | M&L for Ceramic coloured/ printed non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.11 Sqm but n. exec. 0.18 Sqm laid as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement sand mortar ( 1:4) and pointed with coloured cement to match with surfaces of tiles & including Dismantling of old Ceramic coloured/ printed non-skid tiles of any thickness including cement morter bedding (but not backing), removing serviceable tiles to the stores and rubbish off the premises.complete all as specified and directed by Engineer-in-Charge. |
| 7 | M&L Glazed Ceramic Coloured Tiles, 450x350x7mm thick, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick screed bed in cement mortar 1:4 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, & including Dismantling of old Ceramic coloured/ printed non-skid tiles of any thickness including cement morter bedding (but not backing), removing serviceable tiles to the stores and rubbish off the premises.complete all as specified and directed by Engineer-in-Charge. |
| 8 | Dismantling of One Way Trellis work (Jafri), including taking down battens/support with in trellis.( Work has to be done inside shaft above ground floors.) |
| 9 | M & L for precast cement concrete louvres and jallis, 25 mm thick(measured solid) of type B0 1:2:4 (12.5 mm graded aggregate and set in cement mortar 1:4),preparation of surfaces,primer of surfaces new surface including all moulding but excluding frame complete all as speified and directed.( Work has to be done inside shaft above ground floors ) |
| 10 | M&L Providing precast cement concrete in win-dow or door,cills,lintels columns, posts,boundary pillars bed plates,pintle blocks, type B-1 1:2:4(20mm aggregate) a with plan fair faces including chamfers weatherings,throat-ing etc.and setting in motar complete all specified and directed..( Work has to be done inside shaft above ground floors ) |
| 11 | Dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar up to 110 mm dia complete all as specified and directed by Engr-in-Charge. |
| 12 | S&F 110mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed by Engr-in-Charge. Note- .( Work has to be done inside shaft above ground floors ). |
| 13 | S&F 75mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed by Engr-in-Charge. Note-.( Work has to be done inside shaft above ground floors ). |
| 14 | S&F 110 mm dia PVC SWR Bend complete all as specified and as directed by Engr in Charge. ( Work has to be done inside shaft above ground floors ) |
| 15 | S&F 75 mm dia PVC SWR Bend complete all as specified and as directed by Engr in Charge..( Work has to be done inside shaft above ground floors ) |
| 16 | S&F 110 mm dia PVC SWR Tee complete all as specified and as directed by Engr in Charge. .( Work has to be done inside shaft above ground floors ) |
| 17 | S&F 75 mm dia PVC SWR Tee complete all as specified and as directed by Engr in Charge.( Work has to be done inside shaft above ground floors ) |
| 18 | S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 75 mm dia pipe .complete all as specified and as directed by Engr in Charge.( Work has to be done inside shaft above ground floors ) |
| 19 | S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 110 mm dia pipe .complete all as specified and as directed by Engr in Charge..( Work has to be done inside shaft above ground floors ) |
| 20 | S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situ-ation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc., complete all as specified and as directed.Note- Work has to be done in occupied or vacant qtrs as per direction of Engr-in-charge |
| 21 | S&F Galvanised Steel Water Tubing 20mm Bore (dia), ‘Medium Grade’ with all ISI marked Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. .complete all as specified and as directed by Engr in Charge..( Work has to be done inside shaft above ground floors ) |
| 22 | S&F Galvanised Steel Water Tubing 25mm Bore (dia), ‘Medium Grade’ with all ISI marked Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. .complete all as specified and as directed by Engr in Charge. .( Work has to be done inside shaft above ground floors ) |
| 23 | S&F Galvanised Steel Water Tubing 32mm Bore (dia), ‘Medium Grade’ with all ISI marked Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc. .complete all as specified and as directed by Engr in Charge. .( Work has to be done inside shaft above ground floors ) |
| 24 | Refixing old steel tubing 20 mm bore (dia) & connections in new or old position (Walls, ceiling, floors, etc.) in any Situation including replacement of old un serviceable fittings such as socket, elbow, tee, union,reducer socket,tee reducer etc. complete all as specified and directed by Engineer-in-Charge..( Work has to be done inside shaft above ground floors ) |
| 25 | Refixing old steel tubing 25 mm bore (dia) & connections in new or old position (Walls, ceiling, floors, etc.) in any Situation including replacement of old un serviceable fittings such as socket, elbow, tee, union,reducer socket,tee reducer etc. complete all as specified and directed by Engineer-in-Charge..( Work has to be done inside shaft above ground floors ) |
| 26 | S&F in repairs plastic water closet seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed by Engineer-in-Charge. |
| 27 | S&F in repair 32 mm bore chromium plated bottle trap for wash hand basin with inlet & outlet screwed for iron pipes or connection including necessary packing , union and cap complete all as specified and as directed by Engineer-in-Charge. |
| 28 | S&F PVC Flushing Cistern 10 LITRE capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including PVC Flush Pipe of polythene 32mm dia for Low Level Flushing Cistern including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down/out Unserviceable Flushing Cistern and connected Items, .complete all as specified and as directed by Engr in Charge. |
| 29 | S&F in repair 610 mm long PVC waste pipe flexible type 25 mm dia suitable for couplings 32 mm dia complete all as specified and directed by Engineer-in-Charge . |
| 30 | S&F in repair waste fitting brass chromium plated of 32 mm dia for wash hand basin with long screwed sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. |
| 31 | S&F in repair waste fitting 75/100 mm size for 40/32 mm dia waste pipe for SS sink with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. |
| 32 | S&F as in repair over head shower 120 mm dia/150mm square size cast copper alloy, chromium plated, fancy type, with swivel joint fixed to 15 mm bore iron pipe complete all as specified and directed by Engineer-in-Charge. |
| 33 | S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 15 mm bore and fixed as in repair complete all as specified and directed by Engineer-in-Charge ..( Work has to be done inside shaft above ground floors ) |
| 34 | S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and directed by Engineer-in-Charge..( Work has to be done inside shaft above ground floors ) |
| 35 | S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 25 mm bore and fixed as in repair complete all as specified and directed by Engineer-in-Charge..( Work has to be done inside shaft above ground floors ) |
| 36 | S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 32 mm bore and fixed as in repair complete all as specified and directed by Engineer-in-Charge..( Work has to be done inside shaft above ground floors ) |
| 37 | S&F in repair 15 mm bore concealed stop cock with adjustable wall flange cast copper alloy chromium plated, fancy type, screwed down high pressure, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge. |
| 38 | S&F in repair (HDPE) water storage LOFT Tank 200 Ltrs capacity in kitchen, hoisted and fixed in position all specified in MES Schedule Part-I, including tank nipple, union and lowering of unservicable Water Storage Tank including dismantling of old water tank complete all as specified and as directed by Engineer-in-Charge. |
| 39 | S&F in repair grating round /circular 75mm/100mm size of stainless steel with hole or with out hole complete all as specified and as directed by the Engineer in Charge. |
| 40 | M&L Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) including Bolts, (excluding Flushing Cistern and Flushing Pipe) fixed-in-repairs, including Making Good disturbed Surfaces with Cement Mortar 1:3, complete all as specified and as directed. |
| 41 | S&F in repair brass CP health faucet with 1 meter chromium plated stainless steel flexible hose and wall hook complete all as specified and as directed by Engr in charge. |
| 42 | S&F in repair Brass CP fancy type Bib Cock 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, .complete all as specified and as directed by Engr in Charge. |
| 43 | S&F in repair Brass phase with washer complete suitable for 15mm bore bib tap/stop cock/Mixer Valve and fixed .complete all as specified and as directed by Engr in Charge. |
| 44 | S&F in repair Brass phase with washer complete suitable for 15mm bore suitable for concealed stop cock and fixed .complete all as specified and as directed by Engr in Charge. |
| 45 | S&F in repair Cap of Capston head of Bib tap/stop cock/Mixer Volve.complete all as specified and as directed by Engr in Charge. |
| 46 | S&F in repair Angle Stop Cock 15mm Bore (dia), fancy type,Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs.complete all as specified and as directed by Engr in Charge. |
| 47 | S&F in repair High pressure PVC connections pipe 600mm long suitable for Hot and Cold water for 15mm size with Brass CP Check nut complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F in repair Centre hole Brass CP mixer for mixing hot & cold WHB Mixer 15mm Bore (dia) screwed down for iron pipe and fixed including taking down unserviceable WHB Mixer of any description, complete as all specified and directed. |
| 49 | S&F in repair Wall Mixer for kitchen sink 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing including Taking down unserviceable Wall Mixer of any description, complete as all specified and directed. |
| 50 | S&F in repair Wall Mixer 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing including Taking down unserviceable Wall Mixer of any description, complete as all specified and directed. |
| 51 | M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mena radius built in cement mortar 1:4 including Demolition of brick work or stone/boulders masonry, built in cement mortar or cement lime mortar, complete all as specified and directed by Engineer-in-Charge. |
| 52 | Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge. Note: .( Work has to be done inside shaft above ground floors ) |
| 53 | M&L Reinforced cement concrete (nominal mix , 1:2:4 B1 20 mm graded agg )in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge. |
| 54 | M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge. Note:.( Work has to be done inside shaft above ground floors ) |
| 55 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. |
| 56 | Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), .complete all as specified and as directed by Engr in Charge. (Note :- Rate included for four storey building including skefolding and all safety measures) |
| 57 | M&L for 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces including finishing even and smooth without using extra cement all as specified and as directed by Engineer in Charge..( Work has to be done inside shaft above ground floors ) |
| 58 | Supply only liquid water proofing compound complete all as specified and as directed by Engineer-in-Charge. |
| 59 | M&L for preparation of newly plastered surfaces of walls by Vacuum based sanding machine complete all as specified, applying wall care putty min 2mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured including primer by auto roller complete complete all as specified and directed by Engineer-in-Charge. |
| 60 | M&L for preparation of plastered or un plastered old decorated surfaces of walls by Vacuum based sanding machine all as specified, removal of nails etc & filling cracks/hole by applying wall care putty (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying one coat oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 61 | M&L for preparation of plastered or un plastered old decorated surfaces of ceiling by Vacuum based sanding machine all as specified, filling cracks/hole by applying wall care putty and applying two coat of white washing by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 62 | M&L for preparation of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 63 | M&L preparation of old painted surfaces of steel & steel based surface of any description no otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 64 | M&L preparation of new or previously steel surfaces of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as specified and as directed by Engineer in Charge. |
| 65 | Supply and Fixing in repairs, Looking mirror of selected quality, of size 900mmx600mmx6mm thick., with brass CP stud 20mm size with necessary fitting as per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 66 | S & F pre-painted galvalume (PPGI/PPGL) corrugated steel sheets of 0.50 mm thickness of approved make and colour, fixed with self-drilling screws and EPDM washers including proper laps, cutting and finishing complete. including dismantling of existing old sheets, removal of fasteners, stacking of serviceable material and disposal of unserviceable material as directed by Engineer-in-Charge, complete. |
| 67 | S&F in repair PVC door frame of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid prelaminated PVC foam sheet mite cut at two corners and jointing with 2 Nos of 150mm long brackets of 15x15mm MS square tube of two vertical door profiles are to be reinforced with 19x19mm MS square tube of 19 guage WPDM rubber gasket weather seal tobe provided throughout frame the door frame shal be fixed to the wall using 100mm long MS screws through the frame by using PVC fastners. A minimum of 04 Nos screws to be provided for each vertical members and minimum 02 Nos of horizontal members,complete all as specified and as directed by Engr in Charge. |
| 68 | S&F for 30mm thick factory made solid panel prelaminated PVC door shutter consisting of frame made out of MS tube of 19 guage thickness and size of 19x19mm for styes and 15x15mm for topo and bottom rails. MS frame shall have a coat of steel primer of approved make and manufacturer. MS frame adhered with 5mm thick heat moulded PVC `L' channel of size 30x75mm forming styles and 5mm thick, 100mm wide PVC sheet for top rail lock rail and bottom rail on either side and 5mm thick 20mm wide PVC sheet as gap inserted for top rail and bottom rail. panelling of 5mm PVC sheet to be fitted in MS frame to the styles and rails with 5mm thick 30mm wide PVC sheet beading on either side and jointed together with solvent cement adhesive etc Complete all as specified and as directed by Engineer- in- Charge. |
| 69 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) upto. 2.50 Sqm each complete all as specified and directed by Engineer-in-Charge. |
| 70 | Dismantling structural steel work incl. steel door,gate,window guard bars,grills etc.complete all as specified and as directed by Engr in Charge |
| 71 | M&L fabricated frame work as in ladder /doors of gate of angle iron or other section with gusset plate rails, braces etc. complete drilled for fixing steel sheeting or other covering door etc to be prepared for hanging complete all as specified and as directed by Engr in Charge. |
| 72 | S&F Mild steel pipe, Chimney bars (straight or camber); bearing bars; tongues or water bars , for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165. complete all as directed by Engr in charge. |
| 73 | S & F stainless steel work of any description such as pipes, bars, chimney bars (straight or cambered), bearing bars, tongues, water bars, railings, window guard bars, frames, supports, brackets, shelves, and similar articles, made from stainless steel of approved grade (minimum SS 304 or SS 316 where specified), in required shapes, sizes and sections, including cutting, bending, drilling, welding, threading, grinding and finishing. The work shall include all necessary fittings, fixtures, fasteners, base plates, clamps, brackets, inserts, anchor bolts, chemical fasteners, and accessories require. complete all as directed by Engr in charge. |
| 74 | M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in coping, benching & for fixing railing, holdfast etc complete all as directed by Engr in charge |
| 75 | Demolition of stone slab and tiles fixed with bedded and jointed of any description. |
| 76 | M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base of floor. |
| 77 | M&L for sand filling under floors or in foundations including watering and consolidation for 50mm thick. |
| 78 | M&L 60mm thick Machine pressed precast concrete inter locking paver block M-35 Gde any shape and size with Grey cement and no pigment conforming to IS 15658-2006 over sand cushioning as specified and as directed. |
| 79 | M&L for 18-20 mm thick machine cut Kota stone slab of size 550mm x 550mm in flooring over cement screed bed 18-20mm thick in CM 1:4 and jointed with gray cement slurry mix with pigment to match the shade of slab including rubbing and mirror polishing in repairs, complete all as directed by Engr-in-Charge. |
| 80 | S & F 4 mm thick Aluminium Composite Panel (ACP) of approved make and shade, having aluminium skins with polyethylene / FR core, fixed with necessary brackets, fasteners, and accessories. Panels shall be cut, bent, and fixed with stainless steel screws/rivets, joints sealed with weather-grade silicone sealant complete for one side finished surface including dismantling and removing existing sheet/cladding carefully and disposing of unserviceable material . complete all as directed by Engr-in-Charge. |
| 81 | Removal, collection, loading, transportation and disposal of debris/malwa from each and every building, shafts, common areas and all connected/approach area, including lifting from scattered locations, stacking, loading into tractor trolley, conveying and unloading at approved dumping site for all leads up to 10 km , each trolley shall be of minimum size 3.0 m × 1.5 m × 0.90 m (L × B × H) or equivalent complete cleaning of site and making good of disturbed surfaces.complete all as specified and as directed by Engr-in-charge |
| 82 | Note :- The amount of Rs 139 against Schedule of Credit on Srl Page 169460.00 shall be deducted from the total amount quoted against Sch 'A' Please Enable Macros to View BoQ information |
