|
| 1 | M&L for 15mm thick cement plaster in CM 1:4 on bricks on concrete surfaces finishing the surfaces even and smooth without using extra cement including taking down existing plaster with two coats of exterior acrylic emulsion paint over a coat of primer on new surface all as specified. |
| 2 | M & L for Rendering dubbing coat over damaged irregular surface of chajjas roof projections ceiling facia etc average 15mm thick in cm 1:4 over cement slurry coat thick @ 3 Kg/sqm making the surface even followed by 5mm thick rendering in CM 1:3 furnished even& rough including making of drip course as reqd complete including roughening surface of old concrete by picking sweeping clean and washing with water all as specified. Note :Rate for form work shall be deemed to be included in the rate quoted by the contractor. |
| 3 | M&L for rendering or plastering work 10mm thick in CM 1:3 in fascia or edging of Chajjas, ceiling and roof projections etc, including taking out pealed off plaster / concrete and making the line in true shape and finishing the surface without using extra cement including applying two coats of exterior acrylic emulsion paint over a coat of primer for facia, chajja, and roof projection etc all as directed by Engr-in-Charge.. |
| 4 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches,pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed |
| 5 | M&L for pre-cast cement concrete block masonry with solid blocks exc. 10 cm in width, type C-1,1:3:6 (using 20mm graded agg) and setting in cement mortar 1:6 complete all as directed |
| 6 | M&L Fly ash brick work using old size bricks, straight or curved on plan exc 6m mean radius built in CM1:6,complete all as specified and directed. |
| 7 | M & L for Providing precast cement concrete, PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate), as in louvres and jallies, 25mm thick (measured solid), including all mouldings, set in CM 1:4 complete all as specified & directed. |
| 8 | M & L for Reinforced cement concrete (nominal mix) 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregates as in coping of walls, canopies, and in the shelves and the like incl form work complete all as specified & directed. |
| 9 | M & L for Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips all as specified & directed. |
| 10 | M&L for 15mm thick cement plaster in CM 1:4 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement , with two coats of exterior acrylic emulsion paint over a coat of primer on new surface all as specified. |
| 11 | M&L for 15mm thick cement plaster in CM 1:6 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement , with two coats of OBD paint over a coat of primer on new surface all as specified. |
| 12 | M&L for Rendering 10 mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement, including taking down existing plaster with two coats of OBD of any tint over a coat of primer all as specified and directed. |
| 13 | M&L for Cement concrete 1:3:6 type C-2 (using 40mm graded agg) as in plinth protection, 75 mm thick and finished even and smooth without using extra cement, including demolition of existing cement concrete all as specified and directed |
| 14 | M&L for 40mm thick Cement concrete 1:2:4 type B-1(using 20mm graded stone aggregate) as in Floor, finished even and smooth without using extra cement, including demolition of existing cement concrete all as specified and directed.. |
| 15 | M&L non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in CM 1:4 and demolition of existing tiles complete all as specified. |
| 16 | M&L non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in CM 1:4 and demolition of existing tiles complete all as specified. |
| 17 | M&L coloured Vitrified Double Charge tiles (Light shade) 8 to10mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in CM 1:4 and demolition of existing tiles complete all as specified. |
| 18 | M&L glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:3 and demolition of existing tiles complete, all as specified. |
| 19 | M&L Granite (of any type), 18- 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platform,WHB plateform and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixer of pigment to match with marble shade including making full curving (Moulding) the edges and demolition existing stone slab complete,complete. all as specified. |
| 20 | M&L for machine cut 20mm to 25mm thick polished cudappah stone slab as in shelves, partitions, cooking platform below granite stone and like including necessary jointing and pointing and making good to disturbed surface complete all as specified and directed |
| 21 | Supply & Fixed rotational moulded polyethylene water storage tank 3 layer white colour waterr tank , non- toxic effect, algea formation protection (made frome Virgin grade of polyetjylene material which is duly stablized with anti-oxidentPlastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete including dismantling existing water tank all as specified and directed. |
| 22 | Supply & Fixed rotational moulded polyethylene water storage tank 3 layer white colour waterr tank , non- toxic effect, algea formation protection (made frome Virgin grade of polyetjylene material which is duly stablized with anti-oxidentPlastic) of capacity 1000 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete including dismantling existing water tank all as specified and directed. |
| 23 | Taking up or down 15 mm GI steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. |
| 24 | S&F 15mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls, ceilings or in floors etc., any type of pipe including all pvc brass fitting, complete all as specified and as directed. |
| 25 | Taking up or down 20 mm GI steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. |
| 26 | S&F 20mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2fixed complete to walls, ceilings or in floors etc., any type of pipe including all pvc brass fitting, complete all as specified and as directed. |
| 27 | S&F 25mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2fixed complete to walls, ceilings or in floors etc., any type of pipe including all pvc brass fitting, complete all as specified and as directed. |
| 28 | M&L cutting chases pinning in brick work for concealing water tubing and making good to facing where required and pointing in cement motar 1:3, cutting n.exc. 10cm girth complete all as specified and as directed. |
| 29 | S&F in repair vitreous China squatting pan Orissa pattern size 580 x 440mm white with integral foot rest ( excluding flushing cistern and flush pipe), including long Arm P-trap (CI) 100 mm dia of lenght up to 700 mm or as per site requirement ,complete including making good to floor all as specified. |
| 30 | S&F in repairs Vitreous China wash down water closet pan (pedestel pattern) ETWC white, including trap connection to drain (outgoing pipe) and to flushing pipe, antisyphonage pipe, PVC jet for Pedestal pattern pan including 450/600mm long PVC connection and plastic water closet seat of white in colour, back closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed. |
| 31 | S&F in repair vitreous china wash hand basin white of bowl size 550 x 440mm including waste coupling and PVC waste pipe, 32mm dia, pillar tap cast copper alloy with capstan heads chromium plated fancy 15 mm bore to be fixed with and including M S brackets complete all as specified and as directed. |
| 32 | S&F in repair white counter top Basin (self-rimming) Oval shape of size 550mm x 430mm x 195 mm fixed in position including waste coupling and PVC waste pipe, 32mm dia. complete all as specified and as directed. |
| 33 | S&F in repair 600mmx450mm bevelled edge looking mirror of selected quality glass of thickness not less than 5.50mm, itched desined corners, fixed to wall with 12mm dia spacers at each corners, all as specified. |
| 34 | S&F in repair 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float ovel handle including brackets and PVC flushing pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified and as directed. |
| 35 | S&F in repair PVC connection 15mm bore size with PTMT nuts and washers of length 450mm/ 600mm complete all as specified and as directed. |
| 36 | S&F in repair Cabinet mirror plastic body for toilet of size 350mmx450mm with 4mm thick looking mirror complete all as specified and as directed. |
| 37 | S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including 32mm dia waste pipe and CP grating and bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 38 | S&F in replacement stainless steel plate rack of size 609mm X 762mm X 254 mm complete all as specified and as directed. |
| 39 | S&F in replacement stainless steel plate rack of size 609mm X 914mm X 254 mm mm complete all as specified and as directed. |
| 40 | S&F in replacement stainless steel plate rack of size 787mm X 914mm X 254 mm complete all as specified and as directed. |
| 41 | S&F in repairs hand shower (health faucet) of cast copper alloy chromium plated with 8mm dia, 1.2m long flexible tube and wall hook complete all as specified and directed by Engr-in-charge. |
| 42 | S & F in repair brass Chromium plated soap dish , fixed to wall with CP brass screws, all as specified and directed. Make: Prayag Cat part No: BA-45 or of equivalent make as per Appx 'A' as approved by GE |
| 43 | S & F in repair Brass Chromium plated towel rail complete all as specified and as directed. |
| 44 | S&F in repair Brass Chromium plated towel ring complete all as specified and as directed. |
| 45 | S&F in repairs Bib Cock long nose quarter turn suitable for 15mm bore pipe long body with flange fancy type brass CP with, screwed for iron pipe or brass ferrule complete all as specified and as directed. |
| 46 | S&F in repairs pillar taps swan neck (wall mounted) suitable for 15mm bore pipe long body fancy type brass CP with capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified and as directed. |
| 47 | S&F in repairs Pillar taps Swan Neck suitable for 15mm bore pipe long body fancy type brass CP with Capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified and as directed. |
| 48 | S&F in repairs Pillar taps suitable for 15mm bore pipe long body fancy type brass CP with screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified and as directed. |
| 49 | S&F in repairs, chromium plated bib cock with wall flange quarter turn complete all as specified and as directed. |
| 50 | S&F in repairs wall mixer brass chromium plated quarter turn with provision for over head shower with 115 mm long bend pipe on upper side connecting legs and wall Flanges suitable for fixing with GI pipes 15mm dia complete all as specified and as directed. |
| 51 | S&F in repair angle cock with flange quarter turn chromium plated cast copper alloy ISI marked, high pressure screwed down complete all as specified. |
| 52 | S&F in repairs Two Way bib taps with wall flange quarter turn suitable for 15mm bore pipe long body fancy type brass CP, screwed down screwed for iron pipe or brass ferrule complete all as specified. |
| 53 | S&F in repair cast copper alloy CP shower arm square 230mm long with flange complete all as specified and directed by Engr-in-charge. |
| 54 | S&F in repair brass chromium plated shower rose 115mm size square (without arm) with swivel joints including fixing arm/ pipe complete all as specified and as directed. |
| 55 | S&F in repair Toilet paper holder of stainless steel, complete all as specified and as directed. |
| 56 | S&F in replacement 75mm bore PVC (SWR) floor trap plain with CP grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate complete all as specified and as directed. |
| 57 | S&F in repair grating round 75 mm/ 100mm size of CP with/without waste hole complete all as specified and as directed. |
| 58 | S&F in repairs 110mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors complete all as specified and as directed. |
| 59 | S&F in repairs 75mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors complete all as specified and as directed. |
| 60 | S&F in repairs 110mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls complete all as specified and as directed. |
| 61 | S&F in repairs 75mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls complete all as specified and as directed. |
| 62 | S&F in repairs PVC (SWR) bends of any radius of 110mm bore complete all as specified and as directed. |
| 63 | S&F in repairs PVC (SWR) bends of any radius of 75mm bore complete all as specified and as directed. |
| 64 | S&F in repairs PVC (SWR) branch piece single (single ‘Y’) equal or unequal for 110mm bore PVC pipe complete all as specified and as directed. |
| 65 | S&F in repair PVC(SWR) branch piece single (single ‘Y’) equal or unequal for 75mm bore PVC pipe complete all as specified and as directed. |
| 66 | S&F in repair for PVC (SWR) junction single (single ‘T’) equal or unequal with access door for 110mm bore pipe complete all as specified and as directed. |
| 67 | S&F in repair for PVC (SWR) junction single (single ‘T’) equal or unequal with access door for 75mm bore pipe complete all as specified and as directed. |
| 68 | Removing of vegetation / plantation on the wall/ roof/ any position of up to double storey building including necessary scaffolding and roots, girth n. exc. 10cm each and applying chemical treatment with GLYPHOSATE 41% and making good of surface including removing /refixing of CI/GI pipe lines complete all as specified and as directed. (Note : Brick work, plaster and CI/GI pipe lines shall be measured and paid separately) |
| 69 | M & L Textured heavy duty exterior tiles of size 300mmx300mmx10mm thick ,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including a screed bed of 15mm thick in CM (1:4) including demolition of existing tiles complete, all as specified. |
| 70 | Taking out old rusted/unsv, structural steel work such as steel windows/ventilators and removing same from work site complete including necessary cuttings in brick walls all as directed. |
| 71 | S&F Aluminium powder coated louvered ventilator using rectangular tube of size 63.5X52X1.5mm thick, blades set, with provision of exhaust fan using aluminium section heavy duty including glass 4mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc., complete all as specified and directed. |
| 72 | Supply and fix for aluminium powder coated three track sliding window with two glazed shutters with 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make complete all as specified and directed. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604. |
| 73 | Taking down chowkats or frames not exc. 1.5 sq. m each with shutters of any description (without taking off shutters from the frames) complete all as specified and directed |
| 74 | All as per srl item No. 73 above but exc. 1.5 sq.m but n exc 4 sqm each complete all as specified and directed |
| 75 | Taking down shutters of any description not exc. 1 sq. m each complete all as specified and directed |
| 76 | All as per srl item No. 75 above but exc. 1 sq. m but n exc 2 sqm each complete all as specified and directed |
| 77 | S&F Factory made 100 % solid wood plastic composite(WPC) door frame, double rebate 125 mm x 45 mm made from wood plastic composite ( Single extruded process) material with density 780 Kg/ Cum, all as specified and directed.NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement. |
| 78 | S&F Factory made 100 % solid wood plastic composite(WPC) door frame, single rebate 90 mm x 45 mm made from wood plastic composite (Single extruded process) material with density 780 Kg/ Cum and complete all as specified and directed.NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement. |
| 79 | S&F factory Made Solid PVC Molded shutter of 28 to 30 mm thick (stiles), consisting of frame made up of MS tube of size 40mm X 20mm (19 gauge) for top, bottom rail, and in stiles rail, with 2, 4, or 6 raised panel design with 5mm thick Moulded Prelam PVC Sheet on the front face & 5mm thick Prelam PVC sheet on back face. Inside core shall be of PVC solid board of 20 mm thick. Door shall be provided with 20 mm thick Pvc lipping all around the edges, fixing in frame at site complete all as specified and directed Note : All screws shall be self tapping and length of Screw not less than 50 mm. |
| 80 | Supply and fix for 35mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including second class hard wood plain cover fillets 35X6mm all around the shutters including two coat of synthetic enamal paint over one coat of pink primer complete all as specified and directed. |
| 81 | Supply and fix second class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats. |
| 82 | Supply and fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 83 | S &F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples complete all as specified and as directed. |
| 84 | S&F 3mm thick sheet glass ordinery quality and glazing with oil putty in square n exc. 0.50 Sqm in each pane including hacking out existing broken glass complete all as specified and as directed. |
| 85 | S&F Stainless steel butt hinges medium weight 100mm complete all as specified and as directed. NOTE :- All screws shall be self tapping chrome plated and length of screw not less 38 mm |
| 86 | S&F in repair, 150mm/ 300mm, Mild steel spring for door, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed. |
| 87 | S&F Stainless steel sliding door bolts, plate type, bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate 250 mm long (selected quality as approved) complete all as specified and as directed. |
| 88 | S&F Stainless steel Tower Bolt of 200 mm long (selected quality as approved) fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 89 | S&F Stainless steel Handel of 150 mm ( selected quality as approved ) long fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 90 | S&F in repair floor door stopper of stainless steel and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as directed and specified. |
| 91 | S&F Stainless steel Hasp and staple of 100 mm size including bolt to hinge plate fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 92 | S & F 18 mm thick UV coated exterior grade MDF board duly edge banded with 0.8 mm thick PVC taping, fitting of shutters shall be fixed as approved by GE suitable for cup board etc. including taking down with existing one complete all as specified and directed. |
| 93 | S&F Shelves made of HDHMR (high density high moisture resistance) board manufactured with hard wood, prelaminated both sides white in colour 18 mm thick water resistant, termite resistant, duly edge banded with PVC taping 0.8 mm thick, cut to shape & size of shelves including taking down with existing one complete all as specified and directed. |
| 94 | S&F Continuous (piano) hinges, stainless steel, Width of flaps (when open) in 20mm, 0.8mm thickness complete all as specified & directed. |
| 95 | S&F Stainless steel Handle of 75 mm size (modular selected quality of design as approved) fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 96 | Supply and fix in repair for fibre glass reinforced translucent plain sheeting 2.00 mm thick fixed with coach screw and washer in gate, wall etc complete all as specified and as directed. |
| 97 | S&F in repairs Magnetic and connected plate to shutters and frame complete all as specified and directed. |
| 98 | M&L for providing PCC (1:4:8) type D2 using 40mm graded aggregate in sub base including dismantling of existing floor complete all as specified and as directed. |
| 99 | M&L for framed work such as grills gratings etc with ends of bars shouldered and or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framed work of water tanks and similar work complete all as specified and as directed. |
| 100 | Supply and fix in repair for corner glass shelf of size 300mm dia and 8mm thick with chromium plated railing, fixed with and including chromium plated bracket complete all as specified and as directed. |
| 101 | Supply and fix in repairs plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated hinging device for pedestal pattern WC/ semi pedestal and pattern WC (anglo Indian type) complete all as specified and as directed. |
| 102 | S&F in repair Vitreous china Urinal, Half stall type, white with waste pipe and CP brass spreader complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe including Cp Urinal spreader for fixing with 15 mm dia pipe complete all as specified. |
| 103 | Supply and fix repairs decorative type curtain rod , stainless steel, 25 mm dia with not less than 1mm wall thickness complete all as specified and directed. |
| 104 | Supply and fix decorative type brackets , stainless steel U type hook, suitable for above curtain rod complete all as specified and directed. |
| 105 | M&L for complete removal of existing treatment on walls, preparation of surfaces and make surface free from loose particles, oil stains etc and surface ideally prewetted and applying white cementitious wall care putty average thickness 1.5mm complete all as specified and directed by Engr-in-charge. |
| 106 | M&L for preparation of old plastered or unplastered surfaces of wall incl cornices, pillasters by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of OBD complete all as specified and directed. |
| 107 | -Ditto- all as per item No 106, above but applying in two coats of OBD complete all as directed |
| 108 | -Ditto- all as per item No 106, here in before but one coat of OBD on ceiling surfaces |
| 109 | M&L for preparation of old steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enemel paint complete all as specified and directed by Engr-in-Charge |
| 110 | M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enemel paint complete all as specified and directed by Engr-in-Charge |
| 111 | M&L for preparation of old wall surface of any description, width or girth, application of resin pigment and hardener to desired colour spfd pattern and applying one coat of acrylic emulsion paint(Apex) with spray guns, compressor etc in any height of Bldg complete all as specified and directed by Engr-in-Charge |
| 112 | -Ditto- all as per item No 111 above but two coat of acrylic emulsion paint complete all as directed |
| 113 | M&L for preparation of old plastered or unplastered surfaces of wall incl cornices sufaces and applying 8-10 mm thick Level Maxx Plus white cement based self curing mortar (Active bonding polymer) including necessary scaffolding, complete all as specified and directed. |
| 114 | M&L for preparation of old plastered or unplastered surfaces of ceiling/ chajja sufaces and applying 3-5 mm thick Level Maxx Plus white cement based self curing mortar (Active bonding polymer) including necessary scaffolding, complete all as specified and directed. |
| 115 | Dismantling of wall/ceiling board of any description and any thickness including cover fillets etc complete all as specified and as directed. |
| 116 | M&L position suspended false ceiling system using T-grid suspended ceiling grid system. The size of grid shall be 600x600mm, with GI frame work main runner 38 x 24 x 3600mm, cross 'T' 25 x 24 x 60mm/25 x 24 x 1200mm and wall angle 24 x 24 x 2540mm (thickness of the material of 0.30mm ), using 9mm thick ceiling panel laminated with PVC film on front face and foil back available in due drop texture as per IS-2095, part-I-1996, fixed in the grid of T-grid suspended ceiling grid system duly suspended by 4mm dia GI bar hanger from the purlins of the roof with butterfly clips all as specifed and directed by Engineer- in -charge. Make:-Gyproc/Armstrong. |
| 117 | Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site. Please Enable Macros to View BoQ information |
