|
| 1 | Taking out old existing unservicable damaged draw/flap gate shutter of distributories/ branch canal/minor canal/channel completely after disengaging from hoisting system completely for installation of new gate shutter. The work includes cutting of gates into suitable pieces by gas cutting, removing the same by mechanical means or suitable crane, stacking all the pieces at the suitable place or departmental godown or as directed by the Engineer in charge. The cost includes cost of man power employed for dismantling and cost of consumables like oxygen, accetylene gas, hire charges of machineries, like chain pulley block, gas set, tools & tackles, scaffolding and safety equipments etc including carriage loading & unloading with all lead & lift. |
| 2 | Fabrication , Supply, erection and commissioning of new Slide type vertical lift regulator service gates of Canal/River as per IS: 5620 - 2000/Latest Revisionconsisting of skin plate, vertical and horizantal grider, stiffener etc. made of MS material consisting of angle , channel, beam, plate, flat, etc. conformingto IS : 2062 -2011/latest revision manufactured as per approved drawing and direction including cost of Materials, Machinaries , Manpower, Cutting,ligning, drilling, Welding, Finishing, Consumables, Carriages and all overheads with all leads and lifts complete as per specification (without painting)..(i) Width of Gate shuteer size up to 2 metre |
| 3 | Supply of bearingsC) Bearing no.51111 (SKF)(Thrust bearing) |
| 4 | Supplying, fifling & fixing Gun Metal Nut as per requirement having 1.5/2 T.P.I square thread for screw gearing arrangement, perfectly metting withthe screw rod/gear rod for lifting the draw shutter as per direction of E.I.C. The cost includes cost of materials, man power employed, consumables likecutting tools, emery paper, cloths, , hire charges of machineries, tools & tackles etc including carriage loading & unloading. |
| 5 | Supplying, fifling & fixing of screw rod having square thread of 1.5/2 T.P.I, Material bright steel [EN-8/EN9/forged Cl-4 (45C8) as per IS :1875 1992/latest Revision]. dia and thread length as required and providing with a drilled hole of required dia on the other end after flattened and supplying with one no. bolt and nut of required size and all other components as required as per direction of Engineer-In - Charge. The cost includes cost of material, man power employed, consumableslike cutting tools, emery paper, cloths, , hire charges of machineries, tools & tackles, grease, mobil etc including carriage loading & unloading as perdirection of Engineer in charge.(a) Up to length 3.0 Meter |
| 6 | Painting of Gates of Distributory/Branch/Minor canal/ Pump Coloum pipe/Pump Discharge Pipe & other similar components on prepared surfaces with one coats of zinc phosphate primer (airless spray preferred) 50microns/coat and one coal tar epoxy, 150 microns/coat including cost of all materials,labour, scaffolding etc., complete with all leads and all lifts. |
| 7 | Supplying, fifling & fixing of M.S fabricated pedestal stool of suitable size, consisting of bottom plate, top plate, four nos legs etc febricated with suitable sizes m.s plate, m.s angle conforming to I.S 2062 of latest revision and as per approved drawing & direction of Engineer in charge. The cost includes cost ofmaterials, man power employed for dismantling and fitting fixing, civil works consumables like cutting tools, gas, oxygen, welding rod, anchor bolt ofrequired size, hire charges of machineries, like gas cutting set, welding set, tools & tackles etc including carriage loading & unloading. |
| 8 | Supplying, fifling & fixing of C.I wheel in the screw hoisting system for lifting or lowering the draw shutter.The wheel consisting of suitable size hub to accomodate any size of G.M/C.I nut, rim dia 32mm and four nos arm made of minor dia 30mm. & major dia 36mm rod complete or as per approved drawing & direction of the Engineer-in-charge.The cost includes cost of materials, man power employed for dismantling and fitting fixing, consumables like cutting tools, welding rod, hire charges of machineries, like lathe machine, grinding machine, tools & tackles etc including carriage loading & unloading.(a) Upto 60 cm. dia. Cast Iron wheel |
| 9 | Earthwork from borrow pits over existing embankment or for repairs to embankment, closing breaches etc. within an initial lead of 30 metre and lift of 1.50 metre including breaking clods and depositing the same in layers not exceeding 25 cm. and rough dressing etc. complete as per profile |
| 10 | Cutting uprooting and clearing jungles including shrubs, water weeds, bushes, trees, plants, upto 30 cm. girth including removing as directed byEngineer-in-charge Please Enable Macros to View BoQ information |
