|
| 1 | Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge. |
| 2 | Taking down aluminium door / window shutter carefully from frames for servicing / including replacement of broken pivots,tightening of joints of rails and styles etc complete and refixing in the same opening to obtain smooth functioning complete all as specified and directed by Engineer-in-Charge. |
| 3 | Taking down chowkhats or frames with shutter n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge. |
| 4 | Taking down chowkhats or frames with shutter exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge. |
| 5 | Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge. |
| 6 | Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge. |
| 7 | Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge. |
| 8 | Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 9 | Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 11 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 12 | Dismantling boarding, any description, fixed in any position with nails complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 13 | Dismantling wrought iron or mild steel work of ant description and in any postion not otherwise provided complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. |
| 14 | Installation of rebar by using Hilti hammer drill with carbide drill bit,chemical dispensing gun for inserting and using injection mortar chemical RE-500 V3 or equivalent upto minimum depth of (10 x dia of bar ) as in chajja,beam,lintel,column slab and parapet at any height before inserting an anchor bar.Hole must be free from dust debris,water,oil grease complete all as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.Note :- (i) Reinforcement shall be measured and paid separately.(ii) Rates are inclusive safety measures.(iii) Dia of bar 10/12 mm(iv) Rates are inclusive of injection mortar chemical |
| 15 | Reinforced Cement Concrete nominal mix 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregate as in Chajjas / slab complete all as specified and directed by Engineer-in-Charge. |
| 16 | Plain cement concrete (1:2:4) type B-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base etc complete all as specified and directed by Engineer-in-Charge. |
| 17 | Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge. |
| 18 | Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces, trowelled to even and smooth without using extra cement in patches, complete all as specified and directed by Engineer-in-Charge. |
| 19 | Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement in patches, complete all as specified and directed by Engineer-in-Charge.NOTE: Water proofing compound shall be measured and paid separately. |
| 20 | Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers / slab , shelves inncluding supports, overhangs, etc. also splays between floors and beams, etc. (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge. |
| 21 | TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates \\"grills\\" etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge. |
| 23 | First quality Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors etc. set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 24 | Vitrified ceramic tiles ultra charged 10 mm thick (Square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.0 Sqm, in floor,skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 15mm thick screed bedding layer in CM (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 25 | Glazed ceramic coloured tiles 600 x 300 x 7 mm thick on vertical surface such as skirting , dados and risers to steps over and applying 15 mm thick cement plaster in two laters (8-10mm base coat and 5- 7 mm finshing coat) on prepared wall surface using cement mortar 1:4 (1 cement : 4 coarse sand) mixed with Dr. fixit LW+/ Dr fixit pidiproof LW+ as intergral waterproofing compound, applied. having 4mm width joints with spacers and grouting the joints of flooring with epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10kg of hardener and 0.20 kg of resin per kg) complete all as specified and directed by Engineer-in-Charge. |
| 26 | Granite jet black shade, 16 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick (average thickness) cement mortar (1:4) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge. |
| 27 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 28 | (a) Complete removal of existing treatment by scrapping and sanding with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of diameter of 7\\"/9\\" using a 80 grit sanding paper to make the surface free from dust, loose paint etc. by skilled labour complete all as directed.(b) Material and labour for 2mm thick water proofing cement wall care putty over the prepared wall surface @ 1kg per sqm by mixing the putty powder by adding water as per manufacturer instructions and mixing it in putty mixer with a capacity of mixing 40 kg putty in single go. The putty mixer should have variable speed functioning for preparation of smooth and lump free putty(c) Material and labour for one coat of waterproofing primer/ damp proofing @ 1 ltr per 50 sqft. diluted with 30% by water to be applied using an airless spray machine of with a flow rate of 2 ltr per minute having a pressure of 3300 PSI(d) Allow 4-6 hrs to dry the surface for painting of subsequent coats.(e) Material and labour for applying two coats of interior acrylic emulsion paint on plaster surface using @ 1 ltr per 5 sqm of each coat diluted with 40% of water @ 1 ltr per 5 sqm in each coat using airless spray technology with max working pressure of 3300 PSI and capable of opreating single spray gun with a max material hose length of 100 ft. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard-to-reach areas and penetration of distemper on the surface complete all as specified and directed. |
| 29 | (a) Scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust by skilled labour.(b) Material and labour for 2mm thick water proofing cement wall care putty over the prepared wall surface @ 1kg per sqm by mixing the putty powder by adding water as per manufacturer instructions and mixing it in putty mixer with a capacity of mixing 40 kg putty in single go. The putty mixer should have variable speed functioning for preparation of smooth and lump free putty(c) Appliying one coat of waterproofing primer/ damp-proof primer @ 1 Itr per 5 sqm. diluted with 30% of plasterer ndiluted to be applied using an airless spray machine of with a flow rate of 2l per minute having a pressure of 3300 PS(d) Allow 4-6 hrs to dry the surface for painting of subsequent coats.(e) Material and labour for applying two coats of interior acrylic emulsion paint using airless spray technology with max working pressure of 3300 PSI and capable of opreating single spray gun with a max material hose length of 100 ft. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard-to-reach areas and penetration of distemper on the surface complete all as specified and directed. |
| 30 | (a) Scrapping and sanding with mechanical wall sander ( having mechanicak vacuum mechanism) having RPM not less than 1500, sanding pad of diameter of 7\\"/9\\" using 80 grit sanding paper to make the surface free from dust, loose paint etc. by skilled labour complete all as specified and directed.(b) Material and labour for 2mm thick water proofing cement wall care putty over the prepared wall surface @ 1kg per sqm by mixing the putty powder by adding water as per manufacturer instructions and mixing it in putty mixer with a capacity of mixing 40 kg putty in single go. The putty mixer should have variable speed functioning for preparation of smooth and lump free putty(c) Appliying one coat of waterproofing primer/ damp-proof primer @ 1 Itr per 50 sqft. diluted with 40 % by water to be applied using an airless spray machine of with a flow rate of 2l per minute having a pressure of 3300 PSI.(d) Allow 4-6 hrs to dry the surface for painting of subsequent coats.(e) Material and labour for applying two coats of exterior acrylic emulsion paint on new wall plaster surface using @ 1 ltr per 5 sqm of each coat diluted with 40% of water using airless spray technolgy with siliscon additives, with heat reflectant property which can reduce the painted surface temp by 5 degree and gives excellent protection against UV attack with VOC less than 50 gram/ litre as per the LEEDS sepcifications, anti algal properties in two coats @ 1L/ 64 sqft diluted with water as per manufacturer instructions applied over priming coat with airless spray machine of paint application with a flow rate of 2L per minute having a pressure of 3300 PSI. allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and directed. |
| 31 | Preparation of plastered or unplastered new surfaces of ceiling and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge. |
| 32 | Preparation of plastered old surfaces of ceiling and applying two coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge. |
| 33 | Preparation of old steel or iron surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 34 | Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 35 | Preparation of new or previously untreated steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. |
| 36 | Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. |
| 37 | Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. |
| 38 | 35 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with coloured 1 mm thick mica supplied and fixed complete all as specified and directed by Engineer-in-Charge. |
| 39 | 17-18mm thick HDHMR board, high density, water and termite, boer and fungus resistant, laminated both side fixed with screws to timber frame work as in cupboard shelves, shutters, bathroom doors, kitchen cabinets etc fixed in repair complete all as specified and directed by Engineer-in-Charge. |
| 40 | 35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge. |
| 41 | Solid PVC coloured textured door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge. |
| 42 | Factory Made Solid PVC coloured textured Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed by Engineer-in-Charge. |
| 43 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators,casements/sliding shutters and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with rawl plugs and screws or with fixing clips or with expansion hold fastener of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall not be less than 2 mm thick,smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling. C.P. brass/ stainless steel screws,hinges/pivot and making provision for fixing of fittings wherever required complete all as specified and directed by Engineer-in-Charge.Note :1. The rate is inclusive of rollers,locks,rubber beading,rubber seal etc for sliding/casement shutters required for satisfactory operation of window/ventilator/door.2. Panel fillings other than aluminium filling and necessary fittings shall be measured and paid for separately |
| 44 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge |
| 45 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ Stainless steel dash 100mm/ 125mm long fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 46 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ Stainless steel dash 100mm/ 125mm long fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 47 | Supply and fixing Factory made 30mm thick single extruded WPC (Wood Polymer Composite) solid plain board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 48 | Supply and fixing factory made uPVC Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) |
| 49 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 50 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 51 | Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge |
| 52 | 100 mm Butt hinges, medium weight, cold rolled stainless steel, and fixed with screws or with welding to existing MS frames complete all as specified and directed by Engineer-in-Charge. |
| 53 | Stainless steel butt hinges 100 mm long medium weight type C-21 with stainless steel screws complete ,all as specified and as directed by Engr-in-charge. |
| 54 | 300 mm long, Stainless steel, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge. |
| 55 | 150 mm long Aluminium handles, fancy type,cast type,anodised complete all as specified and directed by Engineer-in-Charge. |
| 56 | Floor door stopper of aluminium alloy body single legged with rubber shoe 75 mm fixed to door shutter complete all as specified and directed by Engineer-in-Charge. |
| 57 | Repairing steel windows by welding various parts eg tower bolts at various heights upto 3rd floor including required fittings such as hinges etc complete ,all as specified and as directed by Engr-in-charge. |
| 58 | Aluminium alloy, anodised, hasp staple (bolt type) 100 mm long hinge pin including fixing with bolts fixed in repair complete all as specified and directed by Engineer-in-Charge. |
| 59 | Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 60 | Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, SS Gde-304, bright finish or electro galvanised (width of flap 30mm), complete all as specified and directed by Engineer-in-Charge. |
| 61 | Aluminium body peg set of 06 pegs complete all as specified and directed by Engineer-in-Charge. |
| 62 | Door closer hydraulically regulated, designation No. 3 universal type, aluminium (extruded seection) body suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 63 | Galvanized chicken wire mesh (hexagonal wire netting) 0.5 mm to 1.00mm dia and mesh opening 12 mm/ 25mm of approved quality, made from GI wire, including cutting, bending, lapping and fixing in position with Gi binding wire, staples, or suotable fasteners as required, complete all as specified and directed. |
| 64 | Galvanished mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.4mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and fixing 5.5mm sheet glass ordinary quality and glazing in squares not exceeding 0.5 sqm in each pane, including necessary fittings up the gaps at junctions i.e, at top, bottom, and sides with required EPDM rubber/ neoprene gasket etc. complete all as specified and directed. |
| 66 | Supply and fixing for figured glass, 5.5mm thick, pin head type and glazing in squares not exceeding 0.5 sqm in each pane, including necessary fittings up the gaps at junctions i.e, at top, bottom, and sides with required EPDM rubber/ neoprene gasket etc. complete all as specified and directed. |
| 67 | 12 mm thick toughened glass (conforming to IS 2553-part 1) (using glass of approved make saint-gobain, modiguard or equivalent) with alll edges machine-polished and necessary cut-outs for fittings, surface-mounted hydraulic top patch closer (no floor cutting required) with adjustable closing and latching speeds, 90° hold-ope feature, and a maximum door weight capacity of 120 kg with double-action opening, adjustable closing, and latching speed (Make: dorma, Hafele, Ozone, OCFH series) bottom pivot, SS 304 handles (600 mm), SS 304 floor lock(Make: Ozonehardware, Ebco, Hafele) including customized frosted office logo manfestation as per approved design complete all as specified and directed. |
| 68 | Material & labour for 20-25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed. Please Enable Macros to View BoQ information |
| 69 | Material & labour for 20-25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed. Please Enable Macros to View BoQ information |
