|
| 1 | Dismantling wrought iron or mild steel work of any description specifically provided for gates, staircase railings, framed truss etc, complete all as specified and directed. |
| 2 | S&F Rolled mild steel for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed. |
| 3 | S & F Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed. |
| 4 | M&L for Preparation of new steel surfaces of any description over 10cm width or girth and application of two coats of synthetic enamel paint over one coat of red oxide primer etc, complete all as specified and directed. |
| 5 | S&F Pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet/ semi corrugated 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws including dismantling (AC corrugated , semi corrugated/ PPGI sheets in roof coverings), complete all as specified & directed by Engineer in charge. |
| 6 | Dismantling, floor, hearth or wall tiling including CM (bedding (but not backing), removing serviceable tiles to store & rubbish off the premises, complete all as specified and directed. |
| 7 | Demolition of cement concrete un-reinforced in ground floors and pavings n.exc 15cm thickness, complete all as specified and directed. |
| 8 | M&L for 25mm thk PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in subbase of floors, complete all as specified and directed. |
| 9 | M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 600X1200 in any pattern of light & dark/ highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles, complete all as specified and directed. |
| 10 | M&L for Non Skid ceramic tiles colour tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified and directed. Note : Work will be in patches or in bulk |
| 11 | M & L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including and over 10mm th screed bed in CM (1:4) and pointed in white coloured cement to match, in floors etc, complete all as specified and directed. |
| 12 | M & L for digitally Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.72 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including and over 10mm th screed bed in CM (1:4) and pointed in white coloured cement to match, in floors etc, complete all as specified and directed. |
| 13 | M & L for Virified Ceramic tiles in skirting 10 mm thick (square/ rectangular) polished, area of each tiles match as the size of floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm backing coat in CM (1:4) and pointed in white coloured cement to match, in floors etc, complete all as specified and directed. |
| 14 | Material & Labour for ceramic out door parking tiles 300mmx300mmx10mmm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 15 mm thick Cement Mortar 1:6, complete all as specified and directed. Note : Work will be in patches or in bulk. |
| 15 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar, complete all as specified and directed. |
| 16 | M & L 20mm thick Granite (of any type) machine cut in, wall lining, steps, jambs, pillars, window cills, skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing and including screed bed 10 mm thick on fair faces of brick work or concrete surfaces in CM (1:6), complete all as specified and directed. |
| 17 | M & L for special treatment for sunken portion of WCs/bath and toilet executed in the following stages :- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris outside MD land etc complete. Stage 2 :- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit or its equivalent make as approved in the proporation/ quantity all as per manufacturer's instructions. Stage 3 :- Apply two coats of water proofing elastomeric liquid membrane of Dr Fixit or by brush application of STP or its equivalent make as approved (The surface after painting one coat shall be allowed to dry for 8 hours before application of next coat) all as per Manufacturer's instructions. Stage 4 :- Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit or its equivalent make as approved in the proportion/ quantity all as per Manufacturer's instructions. Stage 5 :- All CI joints shall filled with mixture of cement fine sand and shalicrete R of STP Ltd or integral water proofing chemical or Dr Fixit or its equivalent make as approved all as per Manufacturer's instructions. Stage 6 :- Making holes in wall/floor and fixing 600mm long 20 mm dia medium grade GI spout for draining the surplus water if any. Stage 7 :- Carry out ponding test for 72 hours to ensure water tightness of repaired sunken portion. Stage 8 :- Sunken floor shall be filled with lean cement concrete PCC (1:5:10) type E2 (using 40mm graded stone aggregate) after satisfactory passing of above mentioned treatment by Engineer-in-Charge. |
| 18 | Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins, arches, pillars etc, complete all as specified and directed. |
| 19 | Material and Labour for Brick work with sub class 'B' brick straight or curved on plan exc 6 mtr mean raddius built in CM 1:6, complete all as specified and directed. |
| 20 | M&L for precast cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in block masonry with solid blocks exceeding 10cm width and setting in cement mortar (1:4), complete all as specified and directed. |
| 21 | Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc, complete all as specified and directed. |
| 22 | M & L for 5 mm thick cement plaster in CM (1:3) on ceiling surfaces and finish the surface fair and even without using extra cement, complete all as specified and directed. |
| 23 | M & L for rendring 15mm thick in cemet mortar 1:6 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and smooth without using extra cement, complete all as specified and directed.Note : WPC will be measured and paid separately. |
| 24 | Supply only integral liquid water proofing compound, complete all as specified and directed. |
| 25 | M&L for preparation of new plastered or unplastered surface of ceiling and applying two coats of oil bound distemper over a coat of wall care putty of 1 mm thickness, complete all as specified and directed. |
| 26 | M&L for preparation of new plastered or unplastered surface of wall and applying two coats of oil bound distemper over a coat of wall care putty of 1 mm thickness, complete all as specified and directed. |
| 27 | Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame, complete all as specified and directed. |
| 28 | Taking down shutters of any description exc 1sqm but not exc 2.00 sqm each, complete all as specified and directed. |
| 29 | S&F solid PVC door frames of size 50x47mm made out of 5mm plain colour PVC sheet supplying and fixing in opening as per specification and drawing shown in SSR, complete all as specified and directed. As approved by Accepting Officer |
| 30 | S&F 30mm thick of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc, complete all as specified and directed. |
| 31 | Supplying and fixing factory made 28-30mm thick single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size modulus of elasticity 850 N/mm” and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. |
| 32 | S&F in repairs anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge all as specified. |
| 33 | S&F Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specifiedall as specified and directed by Engr-in-Charge. |
| 34 | S&F 4.8mm thick sheet glass, ordinary quality and glazing in squares exceeding 0.5 Sqm in each pane, complete all as specified & directed by Engineer-in-charge. |
| 35 | S&F butt hinges 100mm size medium weight cold rolled ms in any type of chowkat or frame including welding if required, complete all as specified and directed. |
| 36 | S&F 150mm size extruded aluminium alloy handles fabricated type, anodised, complete all as specified and directed. |
| 37 | Supply and fix Aluminiumn anodised barrel tower bolts 200mm length of extruded section, complete all as specified and directed. |
| 38 | S & F in repair Bib taps, CP, fancy type long nose with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete fixed, complete all as specified and directed. |
| 39 | S&F in repairs 15mm bore stop valves, cast copper alloy, chromium plated fancy type with long shank cup (Concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 40 | S&F in repairs Angular Stop Cock, CP, fancy type with wall flange, fancy type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete fixed, complete all as specified and directed. |
| 41 | S&F in repairs Brass CP wall Mixer 3 in 1 System with provision for overhead and hand shower suitable 15mm bore of pipe, complete all as specified and directed. |
| 42 | S & F in repairs brass chromium plated Health faucet with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed. |
| 43 | Supply & Fixing in repair 15mm bore tubes medium grade galvanized with all fittings such as Tee, elbows, sockets, unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length, complete all as specified and directed. |
| 44 | Supply & Fixing in repair 20 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length, complete all as specified and directed. |
| 45 | Supply & Fixing in repair 16 mm Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified.and fixed complete to walls and laid in floors of any length, complete all as specified and directed. |
| 46 | S&F in repairs 15mm dia two way angle cock of brass, chromium plated fancy type glossy finish fixed, complete all as specified and directed. |
| 47 | S&F in repairs PVC connection 450mm long and 15 mm dia with brass fly nut at both ends, complete all as specified and directed. |
| 48 | Supply and fixing in repairs PVC Flexible waste pipe 32/40 mm dia having length 900mm with socket for steel sink/WHB upto floor level, complete all as specified and directed. |
| 49 | S&F in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls or laid in floors etc, complete all as specified and directed. |
| 50 | S&F in repairs PVC (SWR) bends 75 mm dia any radius with access door, complete all as specified and directed. |
| 51 | S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. |
| 52 | S&F in repair 110 mm bore PVC (SWR) bends/shoes any radius, complete all as specified and directed. |
| 53 | S & F in repair Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directed joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in PCC 1:2:4, complete all as specified and directed. |
| 54 | Supply & fixing in repair vitreous china wash down water closet of Pedestal pattern white including making connection to trap and to flushing pipe etc complete and making good to floor, complete all as specified and directed. |
| 55 | S & F in repairs plastic EWC seat cover, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed. |
| 56 | S & F in repairs Flushing cistern of PVC 10 ltr capacity valveless syphonic action type, low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size, complete all as specified and directed. |
| 57 | S & F for Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank, complete all as specified and directed. |
| 58 | S & F for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank, complete all as specified and directed. |
| 59 | S & F for Rotational moulded polyethylene water storage tanks of 2000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank, complete all as specified and directed. |
| 60 | S & F for Rotational moulded polyethylene water storage tanks of 3000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank, complete all as specified and directed. |
| 61 | S & F for Rotational moulded polyethylene water storage tanks of 4000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank, complete all as specified and directed. |
| 62 | S & F for Rotational moulded polyethylene water storage tanks of 5000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank, complete all as specified and directed. |
| 63 | S&F in repairs HDPE PVC lid (tank cover) with locking arrangement for any capacity PVC tank, complete all as specified and directed. |
| 64 | S & F in repairs 25mm Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe, complete all as specified and directed. |
| 65 | S & F in repairs 40mm Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe, complete all as specified and directed. |
| 66 | S & F in repairs 50mm Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe, complete all as specified and directed. |
| 67 | S&F in repairs to 5 feet and 5 Nos of Pipe pulley Operated cloth drying system, aluminium anodised outer dia 22mm dia pipes channel assembly, locking system to hide rope knot, polister ropes 4mm dia double core & end cap fitting material etc, complete all as specified and directed.Make :- 5F5P-PIS (Select) Easy dry or other equivalent make , sample as approved by GE. |
| 68 | Dismantling/Demolition of existing roof terracing of cement/brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush/mechanical brush and with water throughly to romove all dust/dirt and loose particles to expose bare concrete roof slab and romoval of rubbish/demolished material out side MD land, complete all as specified and directed.Note : Demolition should be done by chiselling. |
| 69 | M&L for PCC (1:2:4) B-0 using 12.50 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope, complete all as specified and directed.(Note :- Supply only water proofing compound shall be measured & paid separately). |
| 70 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed following:- (a) Cleaning existing surface properly. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) Providing and Laying APP modified water proofing membrane reinforced with non wooven polyster matt with physical propertities as under :- (i) Membrane weight >3.6 Kg/Sqm. (ii) Net wooven polyster weight >160 gm/Sqm. (iii) Softening point of membrane > 150o C. (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/ Sq cm. (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction. (vi) Elongation > 30 %. (vii) Impermeability under water pressure > 3 Kg/Sq cm. (d) Over the membrance provide a finishing with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane. Note:- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane. Please Enable Macros to View BoQ information |
