|
| 1 | Demolition of stone slabs, paver blocks and tiles of any description or thickness in floors/apron laid dry complete all as specified and directed. |
| 2 | Material & Laying for precast Cement concrete paver block of thickness 80mm with matt finish of M-40 grade , laid in design ( as approved by Engr in charge) by combination of two size of blocks 8 inch x 4 inch (coloured) and 4 inch x 4 inch(Coloured) as per the dirn of engr in charge complete all as specified and directed. |
| 3 | M & L machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade rubber moulded with grey cement and pigment with glossy finish complete all as secified and as directed.Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks,laying pattern approved by Engr in charge. |
| 4 | M & L machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade rubber moulded with grey cement and pigment with glossy finish complete all as secified and as directed.Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks,laying pattern approved by Engr in charge. |
| 5 | M&L for parking tiles coloured of size 400x400mmx10-12mm thick set jointed and pointed in neat cement slurry mixed with pigment laid over 15mm thick screed bed in cement mortar 1:4 includind demolition/dismantling old surface/tiles complete all as specified and directed. |
| 6 | M&L for parking coloured tiles of size 600x600mmx20 mm thick set jointed and pointed in neat cement slurry mixed with pigment laid over 15mm thick screed bed in cement mortar 1:4 includind demolition/dismantling old surface/tiles complete all as specified and directed. |
| 7 | Material & Laying for dismantelling and refixing paver blocks of any description after proper sand filling and maintaining proper slope and necessary repair complete all as specified and as directed by Engineer-in-Charge. |
| 8 | M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 9 | Demolition of cement Concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) complete all as specified and directed |
| 10 | M&L for Cement concrete 75mm thick type D-2 1:4:8 as in sub base/sub floors of tiles/blocks complete all as specified and directed. |
| 11 | Material and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 includinguding making joints with or without groove (thickness of joints except at sharp curve shall not to more than 5 mm), includinguding making drainage opening wherever required complete all as specified and as directed by Engineer-in-Charge. |
| 12 | M&L for plain cement concrete 1:2:4 type B-1 using 12.5 mm graded stone aggregate in copings, bed plates including weathering, slightly rounded or chamfered angles and throating and coping on top of brick work as directed including necessary form work complete all as specified and directed |
| 13 | M&L for 75 mm thick plain cement concrete 1:2:4 type B-1 ( using 20mm crushed stone agg ) as in floors ,ramps,hard standing or as in similar work finished even and smooth without using extra cement including form work where required all including cutting grooves as specifed and directed . |
| 14 | M&L 50mm thick PCC, type C-2, 1:3:6, ( using 20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and smooth without using extra cement complete all as specified and directed. |
| 15 | M&L Providing precast cement concrete 1:2:4 type B-0 using 12.5mm graded aggregates RCC louvres and jallies, 50mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4.complete all as specifed and directed. |
| 16 | M & L for reinforced cement concrete nominal mix Type B0 1:2:4 using 12.5 mm aggregate in beams, cantilevers, shelves, bressummers, lintels bands including formwork complete all as spd and directed. |
| 17 | M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified . |
| 18 | Demolition of brick work stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 19 | M&L for brick work in cement mortar 1:4 of old size sub class ‘B' bricks straight or curved on plan exceeding 6mtr mean radius complete all as specified and directed. |
| 20 | All as per above but except bricks complete all as specified and directed |
| 21 | M&L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 22 | Material & Laying for forming fair finished drain or channel 30 cm inner girth in cement concrete , using extra cement, includinguding forms, moulds, mi- tred/stopped ends etc complete all as specified and as directed by Engineer-in-Charge. |
| 23 | Material & Laying for Cement concrete 1:3:6 type C2 ( using 40mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and as directed by Engineer-in-Charge. |
| 24 | Taking down cement plaster on brick or concrete surfaces any description including raking out joints hacking for key scrubbing down with water |
| 25 | M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finishing the surface without using extra cement including scaffolding upto 7 mtr height and curing the surface complete all as specified and directed by Engineer-in-charge. |
| 26 | Preparation of new plastered surfaces and Material & Labour for applying Two or more coats of weather proof exterior acrylic emulsion paint(1st Quality) of required shade (Company Depot Tinted) with silicon additives, over and including priming coat of exterior primer of same make on surfaces of walls complete all as specified and directed. Note :- (a) Height of Bldg : any height (b) Exterior acrylic emulsion paint shall be anit-fungal, dust resistant, water repellant, crack-bridging, weather proof type 1st Quality. Please Enable Macros to View BoQ information |
| 27 | Preparation of new plastered surfaces and Material & Labour for applying Two or more coats of weather proof exterior acrylic emulsion paint(1st Quality) of required shade (Company Depot Tinted) with silicon additives, over and including priming coat of exterior primer of same make on surfaces of walls complete all as specified and directed. Note :- (a) Height of Bldg : any height (b) Exterior acrylic emulsion paint shall be anit-fungal, dust resistant, water repellant, crack-bridging, weather proof type 1st Quality. Please Enable Macros to View BoQ information |
