|
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.Notes:-Demolished material should be thrown out side the defence land including loading,transportation,unloading of debris no extra cost shall be paid to the contractor by department. |
| 2 | Dismantling of floor, hearth or wall tilling, any type flooring including cement mortar bedding (but not backing) and rubbish off the premises. Complete all specified and directed Notes:-Demolished material should be thrown out side the defence land including loading,transportation,unloading of debris no extra cost shall be paid to the contractor by department. |
| 3 | Supply and fix joint free non skid coloured Ceramic tiles 07-08 mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles. |
| 4 | Material and labour for coloured Glazed ceramic tiles in of premium quality vertical surface such as skirting, dado, riser to step etc 600mmX 300mmX 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles. |
| 5 | M&L for pre- polished granite slab machine cut of any shade as approved by GE of 20 mm thick including over cement screed bed including edge moulding to shape cutting and nosing with suitable hole for cylinder gas pipe, kitchen sink ,WHB, grinding and machine polishing to edge to give high gloss finish (Granite finish) with suitable grinding stones and set in screed bed 15mm thick CM 1:4 in single piece for platform complete all as specified and as directed by Engr-in-Charge. |
| 6 | Taking down cement or cement lime plasteron brick or stone walls etc.including raking out joints,hacking for key,scrubbing down with water,etc. in any position all as specified and directed..Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 7 | M & L Rendering 15mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:6) furnished even & fair using extra cement all as specified and directed by Engr-in-charge. |
| 8 | M&L applying 2-3mm thick Altek/Birla white wall care putty on wall/ceilling to obtain smooth surfaces and even finish by using vacume based sanding machine,including preparation of surfaces etc. |
| 9 | M&L Preparation of old plastered or unplastered surfaces of wall including cornices, pillasters by using vacum based sanding maching to remove all smoke dust,moulds,moss and efflorescent salts and removing oily and greasy spots etc applying Two coat of distemper oil emulsion of shade as approved by Engr-in-charge with auto paint roller on old surfaces of walls all as specified and directed. Note- Surface to be made even and smooth by filling the depression if any. |
| 10 | Taking up or down steel tubing 15mm bore and connections all as spd. |
| 11 | S&F in repair 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified. |
| 12 | S&F in repair body fancy type long Body bib taps cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down screwed for iron pipe of 15mm bore complete all as specified. |
| 13 | Supply and fixing in repairs 32/40 mm dia bore PVC flexible pipe for wash hand basin/kitchen sink complete all as specified . |
| 14 | S&F 304 grade stainless steel matte finish double bowl with drain board kitchen sink (large,45 x 20 x 7.5 inch ) made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including 32mm dia waste pipe and CP grating and bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to weast pipe complete all as specified. |
| 15 | S&F in replacement stainless steel plate rack of size 750mm X 750/900mm X 250 mm all as specified |
| 16 | S&F shower water drainer floor Bathroom/kitchen Grating with Anti-Foul Cockroach Trap (Silver) (Center-Hole) Size 36\\" X 4\\" including cutting of tiles/ To be facilitated the fixing of the trap all as specified. |
| 17 | S&F 0.80mm thick PVC edge binding tape around the 18 to 20mm thick PVC shutter colour as directed complete all as specified and directed. |
| 18 | Taking down existing cabinets cupboards and Supply and fixing in repair factory made 20 mm thick solid WPC(wood particle composit) UV Printed prelam sheet having both side wood nature colour for cupboard partitions/slabs of density 600 kg /Cbm bent 90° incl 100% termite/water proof, fire rertradent, Eco friendly, complete as per direction of Engr-in-charge, Manufacture specification. |
| 19 | Supply and fixing in repairsfactory made 18 to 20mm thick solid WPC(wood particle composit)without prelam sheet having both side wood nature colour for cupboard partitions/slabs of density 600kg/Cbm bent 90 incl 100% termite/water proof,fire rertradent,Eco friendly complete all as specified and directed by Engineer-in-charge. |
| 20 | S&F 100mm long aluminium handle cast type anodised complete all as specified and directed. |
| 21 | S&F continuos(piano) Hinges Mild steel bright finish width of flaps (when open) 10mm complete all as specified and directed. |
| 22 | S&F 100mm size hasp and staple aluminium anodised safety type fixed with screws complete all as specified and directed. |
| 23 | S&F 50mm dia polished hardwood knobs fixed with screws complete all as specified and directed. |
| 24 | S&F Magnet ball catcher for cupboard shutter fixed with screws complete all as specified and directed. |
| 25 | S&F in repair vetreous China squatting pan Orissa pattern size 580 x 440mm white with integral foot rest ( excluding flushing cistern and flush pipe), including connection to trap, and to flushing pipe, anty syphonage pipe etc. and including 100 mm dia 'P' or 'S' trap complete incl making good to floor all as specified. |
| 26 | S&F in repairs Vitreous China wash down water closet pan (pedestel pattern) white,including trap connection to drain (outgoing pipe) and to flushing pipe, antisyphonage pipe, PVC jet for Pedestal pattern pan including 450/600mm long PVC connection and plastic water closet seat of white in colour,back closed pattern with flat bottom,and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified. |
| 27 | S&F in repair vitreous china wash hand basin white of bowl size 580 x 450mm including waste coupling and PVC waste pipe, 32mm dia, 15 mm dia bore pipe pillar tap cast copper alloy with capstan heads chromium plated fancy to be fixed in M S brackets complete all as specified. |
| 28 | Supply and fixing in repairs Swan neck Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed |
| 29 | S&F in repair 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float ovel handle incl brackets and PVC flushing pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified. |
| 30 | S&F PVC connection 15mm bore size with two nuts and washers of length 600mm all as specified. |
| 31 | S&F brass chromium plated shower rose 150mm size with swivel joints fixed in repairs including fixing to steel pipe or union all as specified. |
| 32 | S&F in replacement with wall flange stop valve/angle valve chromium plated with long shank concealed type cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down complete all as specified. |
| 33 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) n exc. 1.50 Sqm each incl taking out hold fast. |
| 34 | Supply and fixing Factory made Ventilator 1.25mm thick box type(primer coated)ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick including cutting holes and good dismantled portion in PCC(1:2:4) type B1 four Nos for each window including following fitting welded to frame shutter :(a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf .(d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, including Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with alluminium wire staples and glass pane 3mm thick fixed with MS pin and oil putty including two coats of synthetic enamel paint complete. Make/ Manufacture by 1. M/sTee Pee Amritsar 2. M/s Mahindra Fabricators Hayal Pathankot 3. M/S Dhiman Industries, Mamun: NOTE:- During Fixing of Window, surface Shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement. NOTE:- During Fixing of Ventilator, surface Shall be make good in plumb with existing finishes like cement plaster ,similar wall tile etc and as per site requirement. |
| 35 | Supply and fixing Factory made Steel window 1.25mm thick box type(primer coated)ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC(1:2:4) type B1 four Nos for each window including following fitting welded to frame shutter :(a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) Stainless steel Tower bolt 150mm long-02No per leaf .(d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, including Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with alluminium wire staples and glass pane 3mm thick fixed with MS pin and oil putty including two coats of synthetic enamel paint complete. Make/ Manufacture by 1. M/sTee Pee Amritsar 2. M/s Mahindra Fabricators Hayal Pathankot 3. M/S Dhiman Industries, Mamun: NOTE:- During Fixing of Window, surface Shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement. |
| 36 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw thdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, odules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. ( M.S. hold fast/ lugs or SS dash fasteners shall be paid for including). ®Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. NOTE:- During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster,Filling of concrete 1:3:6 type c-1 hold fast for chowkhat,similar wall tile,floor tile etc and as per site requirement. |
| 37 | S & F factory made single extruded WPC (Wood Polymer Composite) 35mm thick solid wire gauge door shutter including of double wire mesh (steel and aluminium XPM) comprising of virgin polymer of K value 58-60 (Suspension Grade), calciumcarbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 38 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw thdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, odules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. ( M.S. hold fast/ lugs or SS dash fasteners shall be paid for including). ®Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. NOTE:- During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster,Filling of concrete 1:3:6 type c-1 hold fast for chowkhat,similar wall tile,floor tile etc and as per site requirement. |
| 39 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N Face) & 900 N (Edge),minimum ressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to pread of flame of Class A category with property of being termite/borer proof, ter/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 40 | M&L preperation of new or previously untreated surfaces of wood/WPC or based materials of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer comlplete all as spd and as directed. |
| 41 | S&F 100mm long (12Gauge) butt hinges stainless steel anodised and fixed all as specified NOTE :- All screws shall be self tapping chrome plated and length of screw not less 38 mm |
| 42 | S&F Stainless steel Tower Bolt of 200 mm long fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 43 | S&F Stainless steel Tower Bolt of 150 mm long fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 44 | S&F Stainless steel Handel of 150 mm long fixed with Self Tapping screws all as specifed and directed by Engr-in-Charge |
| 45 | S&F in repair Drapery curtain rod of stainless steel 20mm dia complete with bracket heavy duty and side caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw and disturbed area to be made good with existing finishes complete all as specified as directed by Engineer-in-Charge |
| 46 | S&F Door catcher/door magnet for cabinet cupboard fixed with Self Tapping screws all as specifed |
| 47 | M&L for 12mm thick full body vitrified single piece tiles (homogeneous) for stairs with anti skid property and having self embossed grooves (for tread portion) and its skirting in single colour set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles. complete all as specified and directed by Engr-In-Charge. |
| 48 | S&F for water proofing treatment to sunken protion of WC 's, bathroom etc by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating of approved make complete all as specified and directed , comprising of following:- (a) Demolition and removing lean concrete/red najri/moorum (b) cleaning the surface and 15mm thick plaster in cement mortar (1:4) using water proofing compound @ 3% by weight of cement on the floor and side of wall of sunken portion and finishedthe surface even &smooth using extra cement complete (c) First layer of slurry of cement @0.488kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @0.253Kg/Sqm after curing of 4 hour (d) Second layer of cement slurry of cement 0.242 Kg/Sqm mixed with acrylic based polymer modified cementitious complete compound @0,126Kg/Sqm after curing of 4 hours followed with curing of 48 hours (e) after treatment of surface sunken portion to be tested for water tightness any leakage or seepage is observed same to rectify before filling the sunken postion (f) Supply and fixing for providing lean concreate (1;5:10) type E-2 (using 40mm graded crushed stone aggregate) in sunken filling and PVC P/s trap,bend//hill rest bends (any radius) diminishing pieces or tapers,PVC(SWR) pipes 110/75mm bore, single socketd , in any length with rubber ring joints, in any length fixed up to gally trap complete all as all complete all as specified and directed by Engineer-In-Charge. |
| 49 | S & Fin repair 600mmx450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC board or plywood and fixed to plugs with chromium brass screws and cup washers.make cera or eqvl. |
| 50 | S&F in repairs corner glass shelves 225mm fixed to wooden plugs with chromium plated brass screws and cup washers complete. Make:Cera or equivalent.. |
| 51 | S&F soap dish fixed wall and including chromium plated brass screws and wooden /plastic packing |
| 52 | S&F Aluminium anodised, Tubular towel rail 20mm dia complete all as specified and directed by Engineer-In-Charge. Please Enable Macros to View BoQ information |
