Tender For Construction Of 33 Kv Gss With Assosiated Lines (Bori-P Gss) At Diggi 3(Bori-P) And Diggi 4(Morwaniya) Under Aen(O&M) Peepalkhunt, Ajmer-Rajasthan

TDR : 55514037

Tender Notice
BOQ

9 Days Left

Ajmer , Rajasthan

Tender Brief : Tender For Construction Of 33 Kv Gss With Assosiated Lines (Bori-P Gss) At Diggi 3(Bori-P) And Diggi 4(Morwaniya) Under Aen(O&M) Peepalkhunt

Document Fees
₹ 4720 /-

EMD
₹ 70500.0 /-

Tender Value
₹ 35.25 Lakhs /-

Submission Date
25-05-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Construction of 33/11KV GSS
2	Levelling of ground
3	Levelling of ground up to 30 cm.depth. with tractor and T&P required as per condition of ground including removal of rubbish plants from ground & marking of boundary with lime powder.(Including all lead & lifting)
4	Levelling of ground above 30 cm.to 90 CM.depth. with tractor and T&P required as per condition of ground including removal of rubbish plants from ground & marking of boundary with lime powder.(Including all lead & lifting)
5	Trimming of tree branches/plants and preparing route approchases for proposed line.
6	Excavation of pit in ordinary rock which does not require blasting to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit.
7	9 Mtr/ 1.2mx0.6mx1.50 m deep
8	(C)Stay set/Depth of pit
9	Earth work excavation and foundation of platfrom of transformers and brakers including dressing of sides and ramming of bottoms .Liftup to 1.5 Meter including taking out the excavated soil and depositing and refilling of jhiri, watering and ramming and disposal of surplus excavated soil as directed with in a lead of 50 Meter.
10	Hard/dense soil
11	Providing and laying cement concrete including compaction etc, complete using stone aggregate 40 mm nominal size (hand broken) in foundation plinth excluding the cost of shuttering using 1 cement : 5 sand : 10 aggregate mix.Note :1. The rates are all lead of cement, lime, ballast, sand, surkhi and grit etc. at site of work.2. For all concrete work coarse sand shall be used no extra will be paid .3. Concrete mix prepared by power driven mechanical mixer shall be used .4. Under exceptional coditions, where mechanical mixer and vibrator are not used (with the approval of Engineer Incharge reduced by 3% for mechanical mixer and 2% for Vibrator.5. Thickness of the cement concrete should not exceeed 100 mm.
12	Plaster on new surface on walls in cement, sand mortar 1:6 including racking of joint etc. complete fine finsh 25 mm thick.Note :1. The rates for complete work including racking of joints, curing, grinding, mixing and finishing T&P and scaffolding material and cost of material with all lead and lift.2. The rates cover protection of all place and things, requiring protection and cleaing such places and thing of all droppings and splashes of mortar etc.
13	Cement concrete flooring grade 1:2:4 (1-cement :2- coarse sand :4-graded stone aggregate ) rounding off edges etc.but excluding cost of nosing of steps etc. complete.Note :1. The rates for all items inculde all form of work, laying, curing and finishing etc. The rates are for complete work at site, inclusive of all leads.2. The rates cover the preparation and cleaing of all places
14	25 mm thick with 12.5 mm thick nominal size aggregate.
15	75 mm thick with 20 mm thick nominal size aggregate.
16	Masonry for foundation and plinth
17	Randon Rubble stone masonry for foundation and plinth in cement sand mortar 1:6(1 Cement : 6 Sand) including labour charges.
18	Brick masonry for foundation and plinth in Cement sand mortar 1:6 ( 1 Cement : 6 Sand ) including labour charges.
19	Safe carriage of PCC poles including loading / un-loading
20	a) 9 Mtr. Long-400 Kg /11 Mtr. PCC pole
21	Within 10 Kms.
22	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
23	c) 9 Mtr.long 200 Kg. PCC pole
24	within 10 Kms.-
25	Above 10 Km. & upto 30 Km. add for each Km. or part thereof
26	Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails, R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading and unloading and stacking in Nigam store /at work site
27	Within 10 Kms.
28	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
29	Above 30 Kms. Add for each Kms. or partthereof.
30	Safe Carriage of insulator, hardware, cable etc.including loading/unloading and stacking in Nigam.stores etc.
31	Within 10 Kms.
32	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
33	Above 30 Kms. Add for each Kms. or part thereof.
34	Safe carriage of fabricated lattice towers structures and sub-station structures type AB, AB beams, isolators structures etc. including loading/unloading and stacking in the Nigam. Stores / at work site.
35	Within 10 Kms.
36	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
37	Above 30 Kms. Add for each Kms or part thereof.
38	Safe carriage of 11/.4 KV 3 Phase distribution transformer including loading/unloading.from store to site(b) 25 & 40 KVA
39	Within 10 Kms.
40	Above 10 Kms. & upto 30 Kms Add for each Km.or part thereof.
41	Above 30 Kms. Add for each Kms. or part thereof.
42	Safe Carriage of 33/11 KV Power Transformer (b) Above 3.15 MVA & Upto 5 MVA
43	Within 10 Kms
44	Above 10 Kms & upto 30 Kms . Add for each Km or partthereof
45	Above 30 Kms & upto 50 Kms . Add for each Km or partthereof
46	Above 50 Kms . Add for each Km or part thereof
47	Safe carriage of breakers/kiosks etc. including loading/ unloading and stacking in Nigam stores
48	Within 10 KMs.
49	Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof
50	Above 30 Kms. and upto 50 Kms.Add per each km,or part thereof
51	Above 50 Kms.Add per each km,or part thereof
52	Safe Carriage of 33/11 KV Power Transformer
53	Safe loading of power/ distribution transformer.
54	Above 1.6 MVA & 3.1 5 MVA
55	Safe unloading of power/distribution transformers
56	Above 1.6 MVA & upto 3.15 MVA
57	Erection &assembly of 2 Pole structures of steel supports or PCC poles in excavated pit in alignment after checking the same with plumb line.Including fixing of top bracing of M.S.Channels with pilot plates and clamps.The support is to be back filled with soil with proper ramming.The nuts &bolts are to be provided by the contractor as per Nigams specfication for which the payment will be made at the prevailing Discom store issue rates.
58	PCC Poles 9 Mtr. Long(200 Kg.)
59	Fixing of all type of fabricated material on erected supports with nut & bolts as per approved design & drawing of sub-station.
60	Fixing of 11kv B&S/T&C type disc insulator for 33kv lines (each unit consiting of 3 nos .disc.& 1set of H/W) on terminal point including fixing of hardware and strips.
61	Fixing of 11kv B&S/T&C type disc insulator of 11kv lines (each unit consiting of 1nos.disc.& 1set of H/ W ) on terminal point including fixing of hardware and strips.
62	Fixing of 11kv B&S/T&C type disc insulator of 11kv lines (each unit consiting of 2 nos.disc.& 1set of H/ W ) on terminal point including fixing of hardware and strips.
63	Fixing of 33kv pin insulator with pins.
64	Assembly. Installation & commissioning of gang operated isolating switch on erected structure with setting for accurate operation including fixing of allied accessories completein all respect with post insulator and jumpering on both ends for connection with the system. The nuts and bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates. (B)G.O. switch . without earthing blade.
65	33kv G.O.switch
66	11kv G.O.switch
67	Assembly and installation of Horn Gap fuse set (set of 3nos)on erected structure as per design, complete in all respectwith post insulator including jumpering on both ends for connection with the system. The nuts & bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates.
68	33kv Horn Gap fuse set.
69	11kv Horn Gap fuse set.
70	Installation of lightening arrestors on erected structure /support (set of 3 nos) including connection with earth by wire /strip as required and jumpering etc. The nuts & boltswill be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates, (A)sub-station type
71	33 KV L.A. set ( 1set=3 Nos)
72	11 KV L.A. set ( 1set=3 Nos)
73	Installation testing as per Nigams norm & commissioning of 11/0.4KV distribution transformer on erected supports including fixing of base channels as per requirment jumpering on HV&LV side, crimping of lugs/ clamping earth connections of body and neutral of transformer with wire /strip (as already provided with earthing ) complete in all respect. The PG clamps nuts & bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates,
74	25 and 40 KVA
75	Fixing of danger plates on supports/structure
76	Fixing of PG clamp of Weasel /Rabbit Conductor
77	Fixing of PG clamp of Dog /Racoon Conductor
78	Assembly,installation & commisioning of 11 KV Roaster switchs on erected structures with stting for accurate operation including fixing of allied accessories completed in all respect with post insulators and jumpering on both ends for connection with systm.The nuts & bolts will be supplied by contractor for which payment will be made as per prevailing Dicom store issue rates.
79	Three no. Earthing of 11/0.4 KV distribution transformer /sub-station with M.S.Rod 20mm dia each 3 meter long and driving them into earth by mechanical means at a distance as per approved design & drawing & specification.The work includes flattening of top ends of M.S.rod drilling a hole of 9/16\\" dia.at flattened top and tightening of M.S.flat 50x6mm/25x3 mm (having 3 hole 2ends and 1mm middle) with nuts and bolts with M.S.rods top end hole.The flat will also be welded with M.S.rod.The end will be connected to equipments as under in sequence.
80	Mesh earthing for 33/11 kv sub-station as per approved map &design usingMS flat 50X6mm/MS road 20mm dia includinglaying of flat/rod at the depth of 0.65 Mtrs.,welding & jointing at joints , structures & equipments etc.asunder:
81	Ordinary rock ( where blasting is not required.)
82	Laying of MS flat /MS rod in 0.65Mtr.deep excavated trench and welding of MS flat/rod continuosly with 100 mm overlaping for straight joint including coating of MS flat joints with molten bitumen and covering joint with bitumen impregnated tape to protect from rust.
83	Shaping of MS flat for connecting the equipments with earthmesh .The work includes the welding of MS flat with equipments/structure and also with earth mesh.The work also includes coating of MS flat joint with molten bitumen and covering jointwith bitumen impregnated tape to protect from rust.
84	Preparation of spikes made of M.S Rod of 20 mm dia and 3 Mtr.length as per design and requirment to be driven in earth by mechanical means and Providing & .fastening of suitable clampswith the M.S. Rod, connection of earth wire/stay wire/MS flat in clamp depending on type of soil:
85	Where drilling is required
86	Filling of trench with available excavated muck in layers of 20cm (Max.)consolidating each deposited layer by ramming & watering with lead up to 50 Mtr, and lift up to 1.5 Mtr.
87	Painting of exposed portion of MS flat/rod with two coats of red-oxide primer and two coats of green enamel paint.including material.
88	Earthing of new 33/11 KV S/S with bentonite compound (including material ) involving following activities. (8.5.1 TO 8.5.6 COVERED)
89	Pipe Earthing for Power Transformer at 33/11KV S/S :-Supply and erection of earthing electrode shall consist of G.I. Pipe 100 mm, of 3 Mtr. Length. The electrode shall be buried as far as practicable 3 Meters below ground level. Wherever possible earth electrodes shall be located as near the water tap, water drain or near down take pipe. Earth electrodes shall not be installed in proximity to a metal fance. It shall be kept clear of the bulidings foundations and in no case it shall be nearer than 2 Mtr. from the outer face of the wall. The electrode shall be surrounded with layer of charcoal dust and salt mixture through out the length. The 100 mm G.I. pipe shall be provided with holes of 12 mm Dia drilled at 75mm interval upto 2.5 meters length from bottom. The top of the pipe shall be provided with a G.I. threaded cap for watering the earth through a pipe. A clamp with pati of 12\\" of M.S. Flat of size 50x6 mm shall be fixed (Bolted) on the top age of the pipe which in turn shall be connected Neutral/Body of the Power Transformer through M.S. Flat size 50x6 mm. The G.I. cap over the G.I. Pipe shall be housed in a masonry chamber, approximately 300 mm x 300 mm x 300 mm deep. The masonry chamber shall be provided with a RCC Inspection cover resting over a RCC frame, embedded in masonry.
90	Erection of PCC poles in excavated pit in alignment after checking the same with plumb line as per approved design & drawing of 33/11kv sub-station.The pit should be back filled with the soil with proper ramming below 30cm ground level and then muffed above 15cm average ground level with cement concrete ratio1:3:6.The charges for muffing will be paid extra as per chapter code no 5.7 The nuts & bolts will be supplied by the contractor for which payment will be made at the prevailing store issue rates. (B) IN RURAL AREA
91	PCC Poles 9 Mtr. Long
92	Laying / stringing of bus bar with ACSR Dog & jumper connection using tie rod ,33KV /11KV insulator strings,required hardware,P.G.clamps/T clamps etc.as per requirement including Y-connections at bus bar jumpering point as per the direction of engineer in-charge.
93	ACSR DOG/RABBIT
94	Supply, stacking & spreading of stone boulders 40 mm. Mono size.(Less voids 17%)
95	Erection of OCB/Kiosk/VCB complete with accessories including use of special tools & conducting all pre-commissioning test before energization,filling oil etc. complete in all respect with erection & grouting of structure (excluding civil works). The relays will be tested by Discom.
96	33 KV VCB/SF-6 Breaker
97	11 KV VCB (Outdoor )
98	Installation of current/potential transformers on supporting structure including checking of wiring & conducting all pre-commissioning tests before energization & satisfactory operation in all respect (The CT/PT set will be tested by Discom).
99	33 KV CT(1 set of 3 Nos.) OR PT Set
100	11 KV CT(1 set of 3 Nos.) OR PT Set
101	Laying, testing termination of control cable 1100 volts PVC insulated including supply and installation of ferrules to designate various cores of control cables by terminal Nos. of identification including utilization of cable gland. The control cable should be clearly arranged in trenches avoiding crossings including clamping of control cable at regular interval and providing identify tags.
102	12x2.5 Sq.mm.
103	Installation of metering points on 11 KV Out going feeder at 33/11 KV S/S.(a to g)
104	Painting with priming coats or ready mixed red-oxide paint 2 coats of approved make on steel works after cleaning with wire brush / sand paper.(including cost of red oxide)
105	On new surface
106	Painting with aluminium paint of approved brand and manufacturer to give an even surface.(including cost aluminium paint)
107	On new works with two coats.
108	Fabrication of steel structures of M.S angle ,M.S.channel & M.S.Flat including cutting ,drilling as per design and drawing.
109	Other steel items
110	Drilling of holes in MS Channel / Angle /Flat
111	15/16\\" dia holes(23.81 mm dia.)
112	Transportation of CT/PT set (all size) including loading and unloading from Nigam store to site
113	(a) Within 10 Kms.
114	(b) Above 10 Km upto 30 Km. Add for each Km. or part there off
115	Supply of MS nuts & bolts
116	Supply of PG Calmps
117	33 KV Line work
118	Conducting route survey as per approved route map and pegging of route with tee off point section point & double pole locations.
119	Trimming of tree branches/plants and preparing route approchases for proposed line.
120	Excavation of pit in Hard soil
121	(B) Lattice Tower /Size of pit
122	12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep
123	(C)Stay set/Depth of pit
124	8'x 3/4\\" -0.75x0.5x1.6 m
125	Excavation of pit in ordinary rock which does not require blasting to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit.
126	(B) Lattice Tower /Size of pit
127	12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep
128	(C)Stay set/Depth of pit
129	8'x 3/4\\" -0.75x0.5x1.6 m
130	Excavation of pit in Hard rock ( Where blasting is required) to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit.
131	(B) Lattice Tower /Size of pit
132	12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep
133	(C)Stay set/Depth of pit
134	8'x 3/4\\" -0.75x0.5x1.6 m
135	Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails, R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading and unloading and stacking in Nigam store /at work site
136	Within 10 Kms.
137	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
138	Above 30 Kms. Add for each Kms. or partthereof.
139	Safe Carriage of insulator, hardware, cable etc.including loading/unloading and stacking in Nigam.stores etc.
140	Within 10 Kms.
141	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
142	Above 30 Kms. Add for each Kms. or part thereof.
143	Safe carriage of fabricated lattice towers structures and sub-station structures type AB, AB beams, isolators structures etc. including loading/unloading and stacking in the Nigam. Stores / at work site.
144	Within 10 Kms.
145	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
146	Above 30 Kms. Add for each Kms or part thereof.
147	Erection of all type of steel supports in the excavated pit in alignment after checking the same with plumb line including fixing of cross arms and top hamper before erecting the supports. The support should be grouted and muffed in cement concrete of ratio 1:3:6 as per item No. 5.7 the remaining portion of the pit will be back filled with soil. The nuts & bolts will be provided by the contractor as per Nigam's specification for which payment will be made at the prevailing store issue rates. The cost muffing and grouting will be paid extra.
148	Lattice Structure
149	Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement,river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of supports/stay set including compaction/curing for 21days in steel plates shuttering /farmer base.
150	Painting with priming coats or ready mixed red-oxide paint 2 coats of approved make on steel works after cleaning with wire brush / sand paper.(including cost of red oxide)
151	On new surface
152	Painting with aluminium paint of approved brand and manufacturer to give an even surface.(including cost aluminium paint)
153	On new works with two coats.
154	Erection & fixing of G.I.Stay sets with anchor plates in excavated pit in required position and back filling with soil with proper ramming.The work includes fixing of stay clamps.Stay insulator with stay wire at both ends with proper tension.Size of stay set/stay wire
155	8\\"x3/4\\" with 7/8 SWG stay wire
156	Laying ,jointing , stringing, tensioning and clamping of conductor with proper sag as directed , using bolted type hardware including binding on pin insulators,jumpering on section points with binding wire / P.G.clamps.Aluminium jointing sleeves will be used for jointing the conductor.The line must stand at proper voltage on charging.The contractor will be provide P.G.clamps for which payment will be made as per prevailing Discom issue rate.
157	(B) IN RURAL AREA
158	ACSR DOG
159	Fixing of 33kv pin insulator with pins.
160	Assembly. Installation & commissioning of gang operated isolating switch on erected structure with setting for accurate operation including fixing of allied accessories completein all respect with post insulator and jumpering on both ends for connection with the system. The nuts and bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates.
161	33kv G.O.switch
162	Fixing and assembly of disc.point channel pair with pilot plates top hampers & clamps on erected single pole structure as per design. The nuts &bolts are to be provided by the contractor as per Nigams specification for which payment will be made as per prevailing Discom store issue rates,
163	33 KV line
164	Laying , jointing,stringing,tensioning and clamping of G.I.Earthwire continuosly on single/double pole by using earth clamps /nuts & bolts with washers and earth reel etc.including proper binding at each end.The nuts and bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates.
165	(A).In Rural Area
166	G.I.Earth wire 6 SWG
167	Fixing of 11kv B&S/T&C type disc insulator for 33kv lines (each unit consiting of 3 nos .disc.& 1set of H/W) on terminal point including fixing of hardware and strips.
168	Supply of PG Calmps
169	Fixing of PG clamp of Dog /Racoon Conductor
170	Fabrication of steel structures of M.S angle ,M.S.channel & M.S.Flat including cutting ,drilling as per design and drawing.
171	Other steel items
172	Drilling of holes in MS Channel / Angle /Flat
173	15/16\\" dia holes(23.81 mm dia.)
174	11 KV Line work for Diggi 3&4
175	Conducting route survey as per approved route map and pegging of route with tee off point section point & double pole locations.
176	Trimming of tree branches/plants and preparing route approchases for proposed line.
177	Excavation of pit in Hard soil
178	(B) Lattice Tower /Size of pit
179	11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep
180	(C)Stay set/Depth of pit
181	6'x 5/8\\" -0.75x0.5x1.35 m
182	Excavation of pit in ordinary rock which does not require blasting to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit.
183	(B) Lattice Tower /Size of pit
184	11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep
185	(C)Stay set/Depth of pit
186	6'x 5/8\\" -0.75x0.5x1.35 m
187	Excavation of pit in Hard rock ( Where blasting is required) to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit.
188	(B) Lattice Tower /Size of pit
189	11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep
190	(C)Stay set/Depth of pit
191	6'x 5/8\\" -0.75x0.5x1.35 m
192	Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails, R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading and unloading and stacking in Nigam store /at work site
193	Within 10 Kms.
194	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
195	Above 30 Kms. Add for each Kms. or partthereof.
196	Safe Carriage of insulator, hardware, cable etc.including loading/unloading and stacking in Nigam.stores etc.
197	Within 10 Kms.
198	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
199	Above 30 Kms. Add for each Kms. or part thereof.
200	Safe carriage of fabricated lattice towers structures and sub-station structures type AB, AB beams, isolators structures etc. including loading/unloading and stacking in the Nigam. Stores / at work site.
201	Within 10 Kms.
202	Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof.
203	Above 30 Kms. Add for each Kms or part thereof.
204	Fixing of 11 KV pin insulator with pins.
205	Fixing of 11kv B&S /T&C type disc insulator of 11kv lines (each unit consiting of 1nos.disc.& 1set of H/W ) on terminal point including fixing of hardware and strips.
206	Fixing of PG clamp of Weasel /Rabbit Conductor
207	Laying , jointing,stringing,tensioning and clamping of G.I.Earthwire continuosly on single/double pole by using earth clamps /nuts & bolts with washers and earth reel etc.including proper binding at each end.The nuts and bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates.
208	(A).In Rural Area
209	G.I.Earth wire 8 SWG
210	Earthing of line for all type of supports as per REC construction standards using Stay wire/GI wire with one pcs.of M.S.rod20mm dia each 3 meter long and driving into earth by mechanical means as per approved design.Drawing &specification.All material except MS rod,MS flat & stay wirewill be supplied by the contractor.If material is supplied by the contractor ,the payment will be made as per prevailing Discomstore issue rates.(In case of PCC poles earthing must be connected with earthwire already available on PCC pole at bottom)
211	Fabrication of steel structures of M.S angle ,M.S.channel & M.S.Flat including cutting ,drilling and continunous welding joint as per design and drawing.
212	Other steel items
213	15/16\\" dia holes(23.81 mm dia.)
214	Erection of all type of steel supports in the excavated pit in alignment after checking the same with plumb line including fixing of cross arms and top hamper before erecting the supports. The support should be grouted and muffed in cement concrete of ratio 1:3:6 as per item No. 5.7 the remaining portion of the pit will be back filled with soil. The nuts & bolts will be provided by the contractor as per Nigam's specification for which payment will be made at the prevailing store issue rates. The cost muffing and grouting will be paid extra.
215	Lattice Structure
216	Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement,river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of supports/stay set including compaction/curing for 21days in steel plates shuttering /farmer base.
217	Painting with priming coats or ready mixed red-oxide paint 2 coats of approved make on steel works after cleaning with wire brush / sand paper.(including cost of red oxide)
218	On new surface
219	Painting with aluminium paint of approved brand and manufacturer to give an even surface.(including cost aluminium paint)
220	On new works with two coats.
221	Erection & fixing of G.I.Stay sets with anchor plates in excavated pit in required position and back filling with soil with proper ramming.The work includes fixing of stay clamps.Stay insulator with stay wire at both ends with proper tension.Size of stay set/stay wire
222	6\\"x5/8\\" with 7/10 SWG stay wire
223	Fixing and assembly of disc.point channel pair with pilot plates top hampers & clamps on erected single pole structure as per design. The nuts &bolts are to be provided by the contractor as per Nigams specification for which payment will be made as per prevailing Discom store issue rates,
224	11 KV line
225	Laying ,jointing , stringing, tensioning and clamping of conductor with proper sag as directed , using bolted type hardware including binding on pin insulators,jumpering on section points with binding wire / P.G.clamps.Aluminium jointing sleeves will be used for jointing the conductor.The line must stand at proper voltage on charging.The contractor will be provide P.G.clamps for which payment will be made as per prevailing Discom issue rate.
226	(B) IN RURAL AREA
227	ACSR RABBIT
228	Supply of PG Clamps
229	Laying energisation & commissioning of underground cable for working voltage of 11 KV/33 KV Aluminium conductor ,Power cable XLPE/PILCA armoured in RCC class NP-2 Non-pressure pipes of sizes mentioned against each refilling of earth in the remaining excavated area making necessary connection including testing etc. as required (It includes providing, laying & jointing RCC class NP-2 Non-pressure pipes conforming to IS:458 of approved make with collars, jointed with CM 1:20 depth of cable shall be 1.2 meter. (Cable shall be provided by the Nigam).
230	(B) 11 KV Cable
231	3x150 sq. mm in pipe of dia 250 mm
232	Installation of cable termination / straight through joints on 11KV Aluminium conductor XLPE /PILCA Cable with outdoor/ indoor termination end and /or straight through joint including required excavation / remoral/ fixing / refixing/ testing etc. as required
233	A) (I) Outdoor end terminal 3x35 Sq mm to 3x185 Sq mm
234	Transportation of CT/PT set (all size) including loading and unloading from Nigam store to site
235	(a) Within 10 Kms.
236	Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof
237	Above 30 Kms. Add per each km,or part thereof
238	Supply of PVC ISI mark 1100 V 12x2.5 mm2 solid copper armoured control cable including lugs & fersules and laying of cable along the DP structure binding with wire at regular interval and making connections from CTPT secondary terminals to TTB. Including utilization of cable gland
239	Fixing of PVC ISI mark 1100 V 12x2.5 mm2 solid copper armoured control cable including lugs & fersules and laying of cable along the DP structure binding with wire at regular interval and making connections from CTPT secondary terminals to TTB. Including utilization of cable gland
240	Transportation and Fixing of meter box of size 525x300x150 mm made by deep drawn method from steel sheet of thickness 1.0 mm duly grey colour powder coated. The viewing window shall be provided with toughened glass of 5 mm thickness of size 120x140 mm. The cover of meter box shall be fixed on inside hinges. The cover shall be provided with neoprene rubber gasket lining fixed with adhessive. Backelite sheet of size 450x275x2 mm for mounting of HTTVM and TTB shall be provided. 4 nos. fixing clamps welded at top of rear face of the meter box of size 50x120x6 mm with 80 mm projection with a rectanguler slot of 17.5mmx50mm. 2 nos. clampsof 50x6mm alongwith nuts, bolts & washers should also provided for fixing the box on pole/joist. 2 nos. welded sealing bolts with nuts and washers should be provided for sealing the box . One hole with matel gland for cable size of 12core 2.5 mm2 control cable should be provided in the center of bottom. The meter box should consist of one 3 phase 4 wire link type meter test termianl block of IMP/CAPITAL make rated for atleast 10 A with cover mounted in the box. Earthing arrangement should be provided one meter box.
241	Installation, testing as per Nigam norms and commissioning of new CT/PT set on erected supports including jumpering wiring crimping of lugs clamping earth connection of body and conducting pre commissioning test before energisation and satisfactory operation in all respect. CTPT set shall be provided by Nigam from concern sub-div stores. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Rajasthan Tenders

Power Generation and Transmission Tenders

Power Transmission Tenders

Transmission Line Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of 33 Kv Gss With Assosiated Lines (Bori-P Gss) At Diggi 3(Bori-P) And Diggi 4(Morwaniya) Under Aen(O&M) Peepalkhunt, Ajmer-Rajasthan

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of 33 Kv Gss With Assosiated Lines (Bori-P Gss) At Diggi 3(Bori-P) And Diggi 4(Morwaniya) Under Aen(O&M) Peepalkhunt, Ajmer-Rajasthan

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us