|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources |
| 3 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 5 | Brick work with common burnt clay F .P .S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 6 | 12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand) |
| 7 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. Laying brick bats with mortar using broken bricks/brick bats 25 mm to 1 15 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (DSR 22.7.1) |
| 8 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete. SOR DSR 13.80 |
| 9 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 10 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work |
| 11 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-T ype sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer . Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) |
| 12 | Supply & fixing of flush door commercial quality conforming to I.S. : 2202 Part I (1983) including fixing of wooden cleats & stopper and including fixing and adjustment of hinges , Bolts locks , handles , springs , fitting with necessary screws to be supplied departmentally.Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) (35mm thick) |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 14 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) |
| 15 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P .V .C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 16 | Fibre reinforced elastomeric liquid water proofing membrane |
| 17 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 18 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 19 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry , but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 20 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 22 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 1 10 mm diameter |
| 23 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F .P .S.(non modular) bricks of class designation 7.5 |
| 24 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 6 graded stone aggregate 20 mm nominal size (Recycled Aggregate (RA) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth |
| 25 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P . Brass pillar taps, 32 mm C.P . brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P . brass pillar taps with elbow including operated levers |
| 26 | Providing and fixing P .V .C. waste pipe for sink or wash basin including P .V .C. waste fittings complete. Flexible pipe 32 mm dia DSR 17.28.2.1 |
| 27 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P . brass screws and washers complete. DSR 17.31 |
| 28 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. DSR 17.73.2 |
| 29 | Providing and fixing C.P . brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore DSR 18.53.1 |
| 30 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply , including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. DSR 18.7.1 & 2 15 mm nominal dia Pipes |
| 31 | 20 mm nominal dia Pipes |
| 32 | Providing and fixing C.P . brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore :DSR 18.49.1 |
| 33 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore DSR 18.17.1A |
| 34 | Providing and fixing G .I. Union in G .I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore DSR 18.46.2 |
| 35 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1000Lt. DSR 18.48 |
| 36 | Providing and fixing ball valve (brass) of approved quality , High or low pressure, with plastic floats complete : 20 mm nominal bore DSR 18.18.2 |
| 37 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore DSR 18.16.1 |
| 38 | Providing and fixing uplasticised PVC connection pipe with brass 45 cm length DSR 18.21.2.1 |
| 39 | Providing and fixing C.P . Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. DSR 18.53A |
| 40 | Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G .I. pipe etc. DSR 18.78 |
| 41 | Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) including disposal of malba DSR 18.79 |
| 42 | Providing and fixing white vitreous china pedestal type water closet (European type W .C. pan) with seat and lid, 10 litre low level white P .V .C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid DSR 17.2.1 |
| 43 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P . brass spreaders with brass unions and G .I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 litre white P .V .C. automatic flushing cistern DSR 17.4.1 |
| 44 | Supply and wiringof submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit concealed in wall, complete with one number 14 SWG copper earth continuitywire including matching colour wash etc., complete in allrespect. (Schedule Item No.- 216B) |
| 45 | Supply and wiring of submain with 20 mm dia heavy duty (2 mm thick) PVC conduit with one No. 2.5 sq. mm. FRLSH PVC insulated multi strand copper conductor cable as earth contuiitywire drawn in conduit. (Schedule Item No.-216C) |
| 46 | As in item no.1304 (B) but in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 number 1.5 sq. mm. FRLSH PVC insulated1100 V grade multi strand singlecore copper conductor as earth continuitywire. (Schedule Item No.-1304C) |
| 47 | Supply and wiringof submain with 25 mm dia heavy duty (2 mm thick) PVC conduit with 2 number 1.5 sq. mm. FRLSH PVC insulated1100 V grade multi strand single core copper conductor cable as earth continuitywire drawn insidethe conduit. (Schedule Item No.-1306C) |
| 48 | Wiring point for light with 1 sq. mm.FRLSH PVC insulated multi strand singlecore copper conductor cable in heavy guage rigid PVC conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire, piano type switch & ceiling rose/ angle/battenholder on 3 mm thick phenoliclaminatedbackelite sheet etc., complete in all respect, as directed includingmatchingcolour (Schedule Item No.-131C) |
| 49 | Wiring point for fan / fesh air fan (light duty exhaust fan) with 1 sq.mm. FRLCHLACH PVC insulated multistrand single core copper conductor cable in heavy guage rigid PVC conduit concealed in the wall, complete with 14 SWG copper earth continuitywire, piano type switch & ceilingrose on 3 mm thick phenolic laminated backelite sheet etc complete in all respect, includingmatchingcolour (Schedule Item No.-133C) |
| 50 | Supply and Fixing of power plug with 20 Amp/250 volt flush type modular switch and 5 pin 20A/250 volt flush type universal modular socket switch on concealed M.S. box inluding supply of all material, labour T&P etc. required for proper completion of work. (Schedule Item No.-1139) |
| 51 | Supply and burying of 600 mm x 600 mm x 6 mm G.I plate vertically for earthing with its top at least 3 metres below ground level complete with 20 mm dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10 SWF GI wire in 15 mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30 cm suare C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at leeast 150 mm thick alround etc. as per direction of Engineer in charge complete in all respect. (Schedule Item No.-703) |
| 52 | S & F of Havells Make Refresh air Fan, Model Refresh air-DX, 250 mm Sweep White & Black etc Complete. (Schedule Item No.-1501(i) |
| 53 | S & F of Havells Make Ceiling Fan, Model Zinger, 1200 mm Sweep White & Brown Colour etc Complete. (Market Rate) |
| 54 | S & F of 6 Amp to 32 Amp. MCB (10 KA) C curve (Schedule Item No.-1002) CAT-A |
| 55 | S & F surface / Flush mounting 8 ways SPN distribution board without additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. (Schedule Item No.-1024) CAT-A |
| 56 | Wiring point for fan/ freh air fan (light Duty exhaust fan) with 1.50 Sq. mm. FRLSH PVC insulated multistrand 2 No. copper conductor cable in heavy guage rigid PVC conduit pipe with 1.5 sq mm FRLSH PVC insulated multistrand copper conductor cable as earthwire wire, piano type switch & ceiling rose/agle/batten holder on 3 m thick phenoilic laminated backelite sheet etc., (Schedule Item No.-133 B) |
| 57 | Supply and fixingof electronicfan regulator(Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work. (Schedule Item No.-1203C) |
| 58 | Supply and fixing of Earthing with GI earth pipe 4.5 metre long 40 mm dia including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work. (Schedule Item No.- 5.1) Please Enable Macros to View BoQ information |
