|
| 1 | Attending complaint day to day for petty repair to easing of door/ window/ cup board shutters by tightening of hinges/ handles/ aldrop bolts/ tower bolts/ knobs/ hasp and staples etc. of any size/ any number of panels for easy closing/ opening or changing the position of hinges, adjustments of tower bolts, sliding bolts, replacement of looking mirror etc. complete including replacement of major defective items if required, complete all as specified and as directed by Engr-in-Charge. |
| 2 | Attending complaint day to day for petty repair to leakage water in bib tap/ pillar tap/ stop cock/ angle valve, flusing cistern, WHB, Sink, wall mixer, etc. of any description any size by changing the washer/ jumper etc. by adjusting/ replacing the washer and adjustment of lever required for making the flushing cistern functional, by tighting the waste pile of WHB/ sink and providing 'M' seal to stop leakage as required. Removal of air lock/ blockage of water in GI tubing and cleaning the pipe or fittings etc. including replacement of major defective items if required, complete all as specified and as directed by Engr-in-Charge. |
| 3 | Note for Item No. 1 & 21. The contractor shall make all arrangements for attending the different types of complaints on every day basis. Any major items required to be replaced with new one to make the system functional shall be measured and paid for separately as \\"S &F\\" under respective applicable item of this schedule. Old retrived items as considered in 'Schedule of Credit' shall become the property of the contractor.2. Contractor shall provide minimum one carpenter and one plumber including all necessary T&P on every alternate days from 9 AM to 5 PM. Additional workers can be engaged if nature of work required to be completed within fix time as desired by GE. Rate shall be quoted accordingly.3. Where material provided shall be paid as \\"S&F\\" under respective item of Sch 'A' the payment of complaint under this item shall not be paid. |
| 4 | S&F in repairs CP bib taps fancy type 15mm bore, cast copper alloy with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 5 | S&F in repairs CP pillar taps fancy type 15mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. |
| 6 | S&F in repairs vitreous china wash basin, white, flat back size 550mm x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets complete all as specified and as directed by Engr-in-Charge. |
| 7 | S&F in repair for sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 8 | S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and as directed. |
| 9 | S&F in repairs 600mm x 450mm mirror of selected quality glass 5-6 mm thick and fixed to walls with necessay PVC frame complete all as specified and as directed. |
| 10 | S&F in repair mirror 5-6 mm thick glass with double coat of protection and longevity grounded edges for safety and silver plating on the back for better reflection including with stainless steel decorative fastener/ studs complete all as specified and as directed. |
| 11 | S&F in repair stop valves/ angle valve 15mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed. |
| 12 | S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) white including necessay fitting etc. complete all as specified and as directed. |
| 13 | S&F in repairs vitreous china squatting pan of orissa pattern size 580mm x 440mm white with `P' or `S' trap, front or back inlet and integrated foot rests, including provision of cement concrete bedding complete all as specified and as directed. |
| 14 | S&F in repair vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, with grating and union for discharge pipe and PVC waste pipe, including making all connections to existing connections, fixed complete all as specified and as directed. |
| 15 | S&F in repair brass chromium plated urinal spreader, fancy type of approved quality fixing with 15mm dia pipe complete all as specified and as directed. |
| 16 | S&F in repair 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (minimum weight for 20 mm – 210 gms) screwed for iron pipe complete all as specified and as directed. |
| 17 | S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, including taking down old PVC connection complete all as specified and as directed. |
| 18 | S&F in repair PVC water closet seat cover, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. |
| 19 | M&L in repairs 32mm dia, 800mm long flexible PVC waste pipe complete all as specified and as directed. |
| 20 | S&F polyethylene water tank cover suitable for upto 1000 Ltrs tanks complete all as specified and as directed. |
| 21 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter lomg flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified and as directed by Engr-in-Charge. |
| 22 | S&F in repair CP grating of size 100mm dia with/ without waste hole complete all as specified and as directed. |
| 23 | M&L for 15mm bore GI tubing medium grade with all fittings fixed to walls, ceiling or laid in floors including taking up or down existing unserviceable steel tubing and connections complete all as specified and as directed. |
| 24 | M&L for 20mm bore GI tubing medium grade with all fittings fixed to walls, ceiling or laid in floors including taking up or down existing unserviceable steel tubing and connections complete all as specified and as directed. |
| 25 | S&F rotational moulded polyethylene water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule including taking down old one complete all as specified and as directed. |
| 26 | All as per Item No. 24 above but 1000 Ltrs capacity. |
| 27 | S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 28 | All as per Item No. 26 above but 110mm bore. |
| 29 | S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete all as specified and as directed. |
| 30 | S&F in repair PVC (SWR) bends of any radius, 75mm dia complete all as specified and as directed. |
| 31 | S&F PVC (SWR) bends of any radius, 110mm dia complete all as specified and as directed. |
| 32 | S&F in repair CPVC pipes 20mm dia (outer dia) SDR 11 and plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and as directed. |
| 33 | Demolition of cement concrete in ground floors and pavings not exc. 15 cm thickness (below or above ground level) and disposing of debries outside MD land complete all as specified and as directed. |
| 34 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 35 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and as directed by Engr-in-Charge. |
| 36 | Dismantling boarding/ partition/ cladding of any description, fixed in any position with nail/ screw complete all as specified and as directed. |
| 37 | M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded stone aggregates) as in sub floors complete all as specified and as directed by the Engr-in-Charge. |
| 38 | M&L for vitrified light shade coloured tiles 9-10 mm thick (squares/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 1.00 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer of mortar 15mm thick in CM (1:6) complete all as specifed and as directed. |
| 39 | M&L for vitrified light shade coloured tiles 9-10mm thick (squares/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 1.00 Sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick plastering in CM 1:4 as in backing coat of tiles complete all as specifed and as directed. |
| 40 | M&L for glazed ceramic coloured tiles of size 350mm x 250mm x 7mm/ 450mm x 300mm x 7mm/ 300mm x 600mm x 7mm thick over and including 10mm thick rendering in cement mortar (1:4) as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed and as directed. |
| 41 | M&L for coloured non skid ceramic tiles 7 to 8mm thick (squares/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 42 | M&L for factory made vitrified heavy duty parking tiles coloured, matt finish, unglazed and unpolished of size 300mm x 300mm x 10mm thick including 15mm thick screed bed in CM (1:4) complete all as specified and as directed by Engr-in-Charge. |
| 43 | M&L for granite of 18 to 20mm thick, work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and moulding edges as directed including screed layer of 15mm thick in CM (1:4) complete all as specified and as directed. |
| 44 | M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in sub base complete all as specified and as directed. |
| 45 | M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design and pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed. |
| 46 | M&L for renewing tiles of any type in patches area n. exc. 5.00 Sqm including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new ceramic tiles to match the existing floor/ wall complete all as specified and as directed. |
| 47 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm) including making drainage opening wherever required complete all as specified and as directed. |
| 48 | M&L for 35 to 40 mm thick precast RCC jallies of type B0 (using 12.5mm graded stone aggregates) of pattern as approved including precast frame, balusters, bressumers, kneelers, string courses fixing in any position with CM (1:4) with demolition of old jallies and thrown outside MD land complete all as specified and as directed. |
| 49 | M&L for preparation of new concrete surfaces of any description over 10cm in width or girth not otherwise discribed and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified and as directed. |
| 50 | M&L for precast cement concrete (1:3:6) type C1 (using 20mm graded stone aggregates) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar (1:6) including demolition of old masonry complete all as specified and as directed by Engr-in-Charge. |
| 51 | M&L for 15mm thick rendering in cement mortar (1:4) or fair faces of brick or cement concrete surfaces, finished even and smooth without using extra cement complete all as specifed and as directed. |
| 52 | M&L for preparation of surface and finishing with two coats of acrylic smooth exterior paint with required shade over a coat of primer complete all as specified and as directed. |
| 53 | Taking down chowkats or frames with shutter (without taking off shutters from the frame) not exceeding 1.5 Sqm each complete all as specified and as directed. |
| 54 | Taking down chowkats or frames with shutter (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed. |
| 55 | Resecuring or easing and adjusting without taking down of shutter of any description, area exceeding 1.0 Sqm complete all as specified and as directed. |
| 56 | Taking down shutters of any description, area exceeding 1.0 Sqm complete all as specified and as directed. |
| 57 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grained PVC sheet and edges will be painted to match with printed sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing complete all as specified and as directed. |
| 58 | S&F factory made solid panel PVC door shutter, 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded wood grain printed PVC sheet used instead of plain colour PVC sheet and 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90°) used instead of exposed portion of PVC sheet beading and joined together with solvent cement and fixing in the frame at site all as per specification and drawing complete all as specified and as directed. |
| 59 | S&F anodised aluminium frame/ shutter section for doors, windows, ventilators, partition etc. with one or more rebates including joining cleat for fixing complete all as specified and as directed. |
| 60 | Add extra for powder coating on above Item No. 58 (minimum thickness of powder coating 50 micron) complete all as specified and as directed. |
| 61 | S&F 4.8 mm thick sheet glass ordinary quality in square exc. 0.50 Sqm each in each pane including necessary rubber beading etc. complete all as specified and as directed by Engr-in-Charge. |
| 62 | S&F 12mm thick prelaminated particle board, interior grade, prelaminated both side of approved colour lamination, fixed with screws to any type of frame work complete all as specified and as directed by Engr-in-Charge. |
| 63 | M&L for 30mm thick flush shutter solid core construction with block board core and plywood face panels, one face is covered with decorative face veneer with lipping/ frame to match complete all as specified and as directed. |
| 64 | Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/ spring clips etc. complete all as specified and as directed. |
| 65 | S&F 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.50 Sqm each in each pane complete all as specified and as directed. |
| 66 | S&F in repair venetian blinds, vertical/ horizontal type, pattern as directed, 100mm wide with polyester fabric of approved colour and pattern with aluminium fittings, top rail and nylon buttons/ loops etc., fixed cuttings and alteration if necessary wherever AC/ coolers exists including dismantling of old unserviceable venetian blinds, complete all as specified and as directed. |
| 67 | S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm with stainless steel wire staples complete all as specified and as directed. |
| 68 | S&F in repair cast iron body door closer, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed. |
| 69 | S&F in repair double action floor spring, hydraulically regulated, made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed. |
| 70 | S&F in repair 20mm dia with 1.0 mm wall thickness drapery rod in any length, high strength stainless steel pipe including bracket/ finials as required complete all as specified and as directed. |
| 71 | S&F aluminium anodised barrel tower bolt, of extuded section and fixed of 150mm long complete all as specified and as directed. |
| 72 | S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 73 | S&F butt hinges, medium weight, cold rolled mild steel of size 100mm complete all as specified and as directed. |
| 74 | S&F extruded aluminium alloy handles fabricated type, anodised, 150mm long complete all as specified and as directed. |
| 75 | S&F in repair 150mm long floor door stopper of aluminium alloy, powder coated, with hard drawn steel spring complete all as specified and as directed. |
| 76 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 77 | S&F in repair powder coated GI grid frame work of size 605mm x 605mm in ceiling fixed with screw suspended with 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40mm x 3mm size, 60mm long complete all as specified and as directed. |
| 78 | S&F 5-6mm thick PVC ceiling board fixed in flat surfaces on snap grid frame work complete all as specified and as directed. |
| 79 | M&L for 12mm thick perforated particle board/ tiles for insulation and accoustic purpose 60cm x 60cm in size, fixed with staples on snap grid including preparation of surface and applying two coats of oil bound distemper on new or previously untreated surfaces of ceiling in patch work complete all as specified and as directed by Engr-in-Charge. |
| 80 | S&F solid PVC wall lining consisting of 5mm thick single side prelaminated PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed. |
| 81 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and as directed. |
| 82 | S&F solar control film 50 micron, reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed. |
| 83 | S&F roof trusses (framed), trussed, purlins, framing for cladding, glazing and like fixed with angle cleats and connecting plates etc. and other similar work conforming to Fe 290-0 Gde E-165 including dismantling of old steel work complete all as specified and as directed by Engr-in-Charge. |
| 84 | M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise discribed and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 85 | S&F in repair 5mm thick coloured ACP sheet cladding of approved colour over MS frame work or any other surfaces including making necessary arrangements for light, vertical , horizontal offset of any size/ any pattern fix in position complete all as specified and as directed. |
| 86 | Dismantling of old unserviceable, rusted, broken (corrugated/ semi corrugated etc.) asbestos cement/ any type of sheets in ridge and roof coverings complete all as specified and as directed by the Engineer-in-Charge. |
| 87 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated trapezoidal shape steel sheet 0.50mm of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. Please Enable Macros to View BoQ information |
