|
| 1 | Material and labour for Cleaning of septic tank by removing manhole cover including removing of earth soil spread over the cover if any from the frame of septic tank and receiving chambers, removing of all night soil sediments and waste materials etc irrespective of its height clearing off upto the bottom floor and dispose off the materials are to be taken from the respective vicinities on covered conveyance and disposed off out of different unit at NAD Alwaye complex or to a distance not exc. 100 mtrs from septic tank to a pit suitably excavated to contain night soil and it shall be covered with excavated earth on top and place back the manhole cover to its original position and removing all vegetable roots if any and making good surround complete all as specified and directed |
| 2 | All as per item No. 1 here in before but manhole of any size and up to 1.5m depth complete all as specified and directed |
| 3 | All as per item No. 1 here in before but manholes of any size and above 1.5m to 3.0m depth complete all as specified and directed |
| 4 | Material and labour for cleaning of PVC/SWG/RCC pipe line 75/100/110 mm dia by mechanical means using cleaning rod or compressor and removal of foreign material after removing the existing blockage below ground including necessary excavation and refilling and making good complete all as specified and directed |
| 5 | Material and labour for cleaning of SWG/PVC/ RCC Pipe line 150mm by mechanical means using cleaning rod or compressor and removal o foreign material after removing the existing blockage below gound level including necessary excavation and making good the disturbed surfaces complete all as specified and directed |
| 6 | Material and labour for cleaning/clearing chock up of IWC/EWC by manual or mechanical means using cleaning rod or compressor etc complete all as specified and directed |
| 7 | Material and labour for cleaning/clearing chock up of floor trap/Nahani trap and gully trap by manual or mechanical means using cleaning rod or compressor etc complete all as specified and directed |
| 8 | Demolition of cement concrete (Unreinforced) in drain, Manhole bed, sewage line bed or in any location or in any position not otherwise specifically provided for complete all as specified and directed |
| 9 | Demolition of brick work, block walling built in cement mortar in any description and in any position complete all as specified and directed |
| 10 | Demolition of reinforced cement concrete cover slabs/guard post etc in any description and in any postion (Reinforcement cut as required to facilitate demolition) complete all as specified and directed |
| 11 | Material and labour for taking down cement plastering any description on brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed |
| 12 | Excavating in trenches nexc. 1.5m wide and nexc 1.5m in depth for foundation,for shafts, wells, cesspits, manholes, pier holes etc and nexc 10sqm on plan and nexc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed |
| 13 | Returning filling in including spreading levelling watering and well ramming in layers nexc 25cm in hard/ dense soil complete all as specified and directed |
| 14 | Removing excavated material (soil) nexc. 50m and depositing where directed at a level nexc 1.5m above the starting point complete all as specified and directed |
| 15 | Supply and fix PVC (SWR) pipe 110 mm dia single socketed, in any length with rubber ring joints, fixed to wall including taking down old pipe complete all as specified and directed |
| 16 | Supply and fix PVC (SWR) pipe 110 mm dia single socketed, in any length with rubber ring joints, laid in trencheSupply and fixloors including taking down/ dismantling old pipe complete all as specified and directed |
| 17 | Supply and fix PVC (SWR) pipe 160 mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors including taking down old pipe complete all as specified and directed |
| 18 | Supply and fix PVC SWR bends 110 mm dia of any radius including taking down old one complete all as specified and directed |
| 19 | Supply and fix PVC (SWR) branch pieces, single (single Y) equal or unequal 110mm bore with access door including taking down/ Dismantling old branch piece complete all as specified and directed |
| 20 | Supply and fix PVC SWR junction single (single T) equal or unequal 110mm bore including taking down/Dismantling old one complete all as specified and directed |
| 21 | Material and labour providing PCC solid blocks exc. 10cm in width type C1 1:3:6, 20mm graded aggregate and setting in cement mortar 1:4 complete all as specified and directed |
| 22 | Material and labour for rendering in CM 1:4,15 mm thick on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed |
| 23 | Material and labour for RCC precast cement concrete in cover slab type B1 1:2:4 using 20mm graded stone aggregate set in CM 1:6 complete all as specified and directed |
| 24 | Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking bending etc, hooking ends for binding with and including MS wire not less than 0.9mm dia complete all as specified and directed |
| 25 | Material and labour for cement concrete 1:2:4 Type B1 using 20mm graded stone aggregate as in surface channels and drains all as specified and directed. |
| 26 | Material and labour 1:3:6 type C2 cement concrete bed to drain pipes including packing under, and haunching against the sides of pipes with concrete after laid and tested for 110mm bore pipe complete all as specified and directed |
| 27 | All as per above item 26 here-in-before but 160mm dia pipe complete all as specified and directed |
| 28 | Material and labour for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required internal dia of pipe100mm complete all as specified and directed |
| 29 | Material and labour for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required internal dia of pipe150mm complete all as specified and directed |
| 30 | Material and labourfor two coat of cement base paint over one coat of alkali resistant primer paint including preparation of new plastered surface complete all as specified and directed |
| 31 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tile to store and rubbihh off the premises complete all as specified and directed |
| 32 | Material and labour for non-skid ceramic tiles, coloured (of approved shade and design), 7 to 8mm thick, of superior quality, square / rectangular 400mmx400mm x7mm tk (area exceeding 0.11 Sqm but not exceeding 0.18 Sqm) , as in floors, etc.set and jointed in neat cement slurry and pointed mixed with colouring pigment to match shade of tiles laid over & including 15mm thick screed bed in CM (1:4) complete all as specified and directed |
| 33 | Material ande labour for glazed ceramic tiles, coloured (light colour as approved), of size 300x 600 x7mm/ 350x250mm x 7mm / 450X 350X 7mm/450x300x7mm /300mmx200mmx7mm thick on vertical surfaces set and jointed in cement slurry over 10mm thick backing coat in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed |
| 34 | Material and labour 100mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) including dismantling of old trap complete all as specified and directed. |
| 35 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete,base concrete, brick work masonry etc and making good disturbed ground complete all as specified and directed |
| 36 | Dismantling fencing wire mesh, any type in existing chain link fencing including line wire complete all as specified and directed |
| 37 | Material and labour cement concrete B2 1:2:4 in foundations (40 mm graded aggregate) filling and mass concrete in post holes etc complete all as specified and directed |
| 38 | Supply only chain link MS galvanised fencing, any size or type complete all as specified and directed |
| 39 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed |
| 40 | Supply and fix mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long but n exc 10cm long and dia of neck 11 to 15mm complete all as specified and directed |
| 41 | Supply and fix mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not lessthan 0.9mm dia or securing with clips Fe-410-W (Gde.E-250) quality-A orFe 290 (Gde -E-165) complete all as specified and directed |
| 42 | Supply and fix in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts ,posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 incl curved or ramped portions of hand rails to required shape or figure (curved, ramped or scroll portions only measured) complete all as specified and directed |
| 43 | Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer completed all as specified and directed |
| 44 | Supply and fix in repairs Galvanised, 2 strand steel barbed wire 2.24 mm dia, barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of strandard rails, straining bolts, inlcuding securing or tying at crossings with and provn of galvanised mild steel wire staples or steel pins etc complete all as specified and directed ( Each line wire to be measured) |
| 45 | Taking down and Re-Fixing Galvanised barbed wire with restraining resecuring incl making good staples etc as in repair complete all as specified and directed |
| 46 | Supply and fix in repairs concertina coil of 600- 610mm diameter made out of 2.5mm dia spring steel core wire 230 G/m2 (minimum) dipped with corrosion preventive fluid (rusilo 901) of castrol make in white colour, each coil having a 50 turns (circles) and an average weight not less than 8.57 Kg (plus or minus 5%) including handle and spike at both ends of coil, errected in position on top of compound wall (stretchable length of each coil 6.25mtr to 7.0 m or as per manufacture approved lenght ) complete all as specified and directedNote :- Dimesnsions and specification shall be varried as per Supplier /manufacture make and also specifications & make shall be approved by GE |
| 47 | All as per above ( Except material in any type/size ) but refixing after taking down in existing concertina coil any size and type incl necessary repair with tightining with binding wire complete all as specified and directed |
| 48 | Demolition of unreinforced cement concrete in ground floor and paving n.exc 15 cm thick below or above ground level complete all as specified and directed |
| 49 | Material and labour cement concrete D2 1:4:8 in foundations (40 mm graded aggregate) filling and mass concrete complete all as specified and directed |
| 50 | Material ande labour for 50mm tk Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection,Floor topping etc , surfaces finished of concrete flooring with brooming complete all as spd u including provision of necessary construction joints complete all as specified and directed |
| 51 | Material and labour Machine pressed precast concrete coloured interlocking paver block any shape and size conforming to IS 15658-2006 of 80mm thick M-40 grade etc complete with grey cement and pigment complete all as specified and directed |
| 52 | Material and labour for filling for 12.5mm Graded coarse aggregate cushing of paver tiles with Spreading and levelling in layers n exc. 25 cm thick in each layer complete all as specified and directed |
| 53 | Material and labour Chequered cement concrete tiles 20cm x 20cm x 25mm thick,or 30cmx30cmx25mm thick or PCC deco tiles set, jointed and pointed in neat cement slurry in floors with grey cement & pigments. With Screed bed or bedding layer of mortar 20mm thick for laying floor finishes in CM 1:6 complete all as specified and directed |
| 54 | Material and labour Providing, cement concrete type B-1, 1:2:4 (20mm graded aggregate)as in hunching, coping , benching etc complete all as specified and directed |
| 55 | Dismantling of floor hearth and wall tilling incl mortar beding removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 56 | Material ande labour colored non skid ceramic of approved shade and pattern, of size 600mmx600mmx9-10mm ( exe 0.18 but not exe 0.38 sqm each ) thick joint less as in floor set and jointed in cement slurry, over 15mm thick screed in cement mortar (1:6) and pointed with epoxy grouted with suitable pigment (mixed with white cement )to match the colour of tiles complete all as specified and directed |
| 57 | Supply and fix vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tile exc 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6. complete all as specified and directed. |
| 58 | Material ande labour for non-skid ceramic tiles, coloured (of approved shade and design), 7 to 8mm thick, of superior quality, square / rectangular 300mmx300mm x6mm tk (area exceeding 0.06 Sqm but not exceeding 0.11 Sqm) , as in floors, etc ( with epoxy filling with 2mm spacers bar ) .set and jointed in neat cement slurry and pointed with colouring pigment to match shade of tiles laid over & including 15mm thick screed bed in CM (1:4) complete all as specified and as directed |
| 59 | Material ande labour for glazed ceramic tiles, coloured (light colour as approved), of size 300x 600 x7mm/ 350x250mm x 7mm / 450X 350X 7mm x300mmx200mmx7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed |
| 60 | Supply and fix in repair 1.25mm thick steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified as directed. |
| 61 | Supply and fix in repair safety leaver locks mild steel with 4 levers for rolling shutters complete all as specified as directed. |
| 62 | Supply and fix in repair ball bearing for rolling shutters complete all as specified as directed. |
| 63 | Taking down existing steel rolling shutters n.exc 10 sqm in area from brackets with all connected fittings such as shaft,helical spring ,bearing,bottom plate,top cover,anchoring rod,haps and staple etc checking for thear function , replacing any worn out and unserviceable parts as required greasing ,welding,reparing,servicing for smooth functioning of shutter and connected items and refixing to their orisinal position complete all as specified and directed (Replacement of items will be measured seperately) |
| 64 | Taking down existing steel rolling shutters exc 10 sqm but n.exc 15 sqm in area from brackets with all connected fittings such as shaft,helical spring ,bearing,bottom plate,top cover,anchoring rod,haps and staple etc checking for thear function , replacing any worn out and unserviceable parts as required greasing ,welding,reparing,servicing for smooth functioning of shutter and connected items and refixing to their orisinal position complete all as specified and directed (Replacement of items will be measured seperately) |
| 65 | Supply and fix bottom plate with 2.5mm thickness and with widtg suitable for fixing of existing shutter including connected items for fixing complete all as specified and directed |
| 66 | Supply and fix steel top cover of thickness not less than 0.9mm and with widtg suitable for fixing to existing rolling shutter and to cover up the top portion completely including end plate and all connetted items ig requires for fixing complete all as specified and directed |
| 67 | Supply and fix steel lath for rolling shutters not less than 1.25mm thick and with strip width suitable for fixing to existing rolling shutters including connected items for fixing complete all as speciified and as directed |
| 68 | Supply and fix helical spring for counter balancing rolling shutters made from high tension steel spring, 7mm thick and 45cm long complete all as speciified and as directed |
| 69 | Dismantling plain/ corrugated steel/ asbestos cement sheet of any gauge thickness and in any position complete all as speciified and as directed |
| 70 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thickness of any colour having tensile strength of 550 Mpa with coating thickness fixed with GI self taping screws as in roof covering/cladding to wall, ridges, valley gutters fixed to frame work all as per manufacturers instructions complete all as speciified and as directed |
| 71 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thickness of any colour having tensile strength of 550 Mpa with coating thickness fixed with GI self taping screws as in roof covering/cladding to wall, ridges, valley gutters fixed to frame work all as per manufacturers instructions complete all as speciified and as directed |
| 72 | Dismantling single layer mangalore pattern or similar tiles in roofing incl removal of vegitation nails etc complete all as speciified and as directed |
| 73 | Material ande labour for roof tiles, mangalore pattern, interlocking at side joints, laid dry with any height of roof , incl necessary scaffolding etc complete all as speciified and as directed |
| 74 | All as per above Item No 73 here-in-before but except tiles ( refixing in existing tiles ) complete all as speciified and as directed |
| 75 | Material ande labour ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 complete all as speciified and as directed |
| 76 | Material ande labour for 2nd class hard wood, well seasoned, battens, clean sawn at 25cm centres, sectional area exc. 15 & n exc. 25 Sqcm including dismantling old u/s battens for tiles, shingles etc, of any size including fillets spaved n.exc 15cm complete all as speciified and as directed |
| 77 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as speciified and as directed |
| 78 | Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 incl one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as speciified and as directed |
| 79 | Preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as speciified and as directed Please Enable Macros to View BoQ information |
