|
| 1 | EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m._All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth. sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | CEMENT CONCRETE (CAST IN SITU) |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 7 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 9 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 10 | REINFORCED CEMENT CONCRETE |
| 11 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: |
| 12 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 13 | Reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15* landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to foor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 15 | Foundations, footings, bases of columns, etc. for mass concrete. |
| 16 | Suspended floors, roofs, landings, balconies and access platform |
| 17 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 18 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level._Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level._Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 21 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 22 | MASONRY WORK |
| 23 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:_Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :_Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 25 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level._Cement mortar 1:4 (1 cement :4 coarse sand) |
| 26 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 27 | CLADDING WORK |
| 28 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 29 | WOOD AND P. V. C. WORK |
| 30 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 31 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 32 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 33 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378)_300x16 mm |
| 34 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : (copper oxidized as per IS: 1378)_200x10 mm |
| 35 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : (copper oxidized as per IS: 1378)_125 mm |
| 36 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 37 | Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive. |
| 38 | STEEL WORK |
| 39 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer._Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 40 | FLOORING |
| 41 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 42 | ROOFING |
| 43 | Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :_With residual type petroleum bitumen of grade VG -10 |
| 44 | 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat:_With common burnt clay F.P.S.(non modular) brick tile of class designation 10 |
| 45 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :_In 75x75 mm deep chase |
| 46 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 47 | Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand)._Stone ware spout |
| 48 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes._110 mm diameter |
| 49 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 50 | Single tee with door_110x110x110 mm |
| 51 | Single tee without door_110x110x110 mm |
| 52 | Bend 87.5°_110 mm bend |
| 53 | Shoe (Plain)_110 mm Shoe |
| 54 | Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete._110 mm |
| 55 | FINISHING |
| 56 | 12 mm cement plaster of mix :_1:4 (1 cement: 4 fine sand) |
| 57 | 15 mm cement plaster on the rough side of single or half brick wall of mix :_1:4 (1 cement: 4 fine sand) |
| 58 | 6 mm cement plaster of mix :_1:3 (1 cement : 3 fine sand) |
| 59 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :_New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 60 | Finishing walls with water proofing cement paint of required shade :_New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 61 | Applying priming coat:_With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 62 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :_Two or more coats on new work |
| 63 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 64 | Dismantling and Demolishing |
| 65 | Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge. |
| 66 | ROAD WORK |
| 67 | Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading,well ramming, consolidating and grouting with jamuna sand,including finishing smooth etc. complete as per direction of Engineer-in- charge. |
| 68 | Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made bytable vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per requiredsize and pattern, finishing and sweeping extra sand. complete all asper direction of Engineer-in-Charge._60mm thick cement concrete paver block of M-35 gradewith approved colour, design & pattern. |
| 69 | SANITARY INSTALLATIONS |
| 70 | Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever) conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required:_White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests |
| 71 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required :_W.C. pan with ISI marked white solid plastic seat and lid |
| 72 | Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm and 340x410x265 mmsizes respectively with automatic flushing cistern with standard flushpipe and C.P. brass spreaders with brass unions and G.I clampscomplete, including painting of fittings and brackets, cutting andmaking good the walls and floors wherever required :_Range of three urinal basins with 10litre white P.V.C.automatic flushing cistern |
| 73 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require:_White Vitreous China Wash basin size 630x450 mmwith a single 15 mm C.P. brass pillar tap |
| 74 | Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete._Flexible pipe_32 mm dia |
| 75 | Providing and fixing 600x450 mm beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washerscomplete. |
| 76 | Providing and fixing soil, waste and vent pipes :_100 mm dia_Sand cast iron S&S pipe as per IS: 1729 |
| 77 | 75 mm diameter :_Sand cast iron S&S pipe as per IS: 1729 |
| 78 | Providing and filling the joints with spun yarn, cement slurry andcement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :_75 mm dia pipe_ |
| 79 | 100 mm dia pipe |
| 80 | Providing and fixing bend of required degree with access door, insertionrubber washer 3 mm thick, bolts and nuts complete._100 mm dia_Sand cast iron S&S as per IS - 1729 |
| 81 | Providing and fixing plain bend of required degree._100 mm dia_Sand cast iron S&S as per IS - 1729 |
| 82 | Providing and fixing double equal plain junction of required degree._100x100x100x100 mm_Sand cast iron S&S as per IS - 1729 |
| 83 | Providing and fixing single equal plain junction of required degreewith access door, insertion rubber washer 3 mm thick, bolts andnuts complete._100x100x100 mm_Sand cast iron S&S as per IS - 1729 |
| 84 | Providing and fixing single equal plain junction of required degree :_100x100x100 mm_Sand cast iron S&S as per IS - 1729 |
| 85 | Providing and fixing sand cast iron S&S off sets as per IS: 1729_76 mm off sets_With 100 mm dia pipe |
| 86 | Providing and fixing collar :_100 mm_Sand cast iron S&S as per IS - 1729 |
| 87 | Providing lead caulked joints to sand cast iron/centrifugally cast(spun) iron pipes and fittings of diameter :_100 mm |
| 88 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm. complete, including cost of cutting and making good the walls and floors:_100 mm inlet and 100 mm outlet_Sand cast iron S&S as per IS: 3989 |
| 89 | WATER SUPPLY |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls_20 mm nominal dia Pipes |
| 91 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 92 | 20 mm nominal dia Pipes |
| 93 | 25 mm nominal dia Pipes |
| 94 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :_25 to 40 mm nominal bore |
| 95 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 96 | 25 mm nominal bore |
| 97 | 20 mm nominal bore |
| 98 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 99 | 20 mm nominal bore |
| 100 | 25 mm nominal bore |
| 101 | Providing and fixing uplasticised PVC connection pipe with brass unions :_30 cm length_15 mm nominal bore |
| 102 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :_With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 103 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 104 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms._15 mm nominal bore |
| 105 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931_15mm nominal bore |
| 106 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 107 | Providing and fixing PTMT grating of approved quality and colour._Circular type_125 mm nominal dia with 25 mm waste hole |
| 108 | DRAINAGE |
| 109 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:_100x100 mm size P type_With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 110 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :_300 mm dia. R.C.C. pipe |
| 111 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :_For pipes 100 to 250 mm diameter |
| 112 | ALUMINIUM WORK |
| 113 | Providing and fxing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :_For fixed portion_Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 114 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):_With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 115 | WATER PROOFING |
| 116 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 117 | M.R ITEMS |
| 118 | Providing and fixingC.P Two in one Bibcock of approved quality confirming toISI standard and weighing not less than 690 gm 15mm nominal Bore |
| 119 | Providing and Fixing C.P health faucetof of approved quality confirming toISI standards and weighing not less than 690 gm 15mm nominal Bore |
| 120 | Add for revised GST @18% in place of 12% ie 6.33% on SR&DR Total 1286435 |
| 121 | Electrical work in newly constructed Toilet for D/O Tourism Jamia Millia Islamia |
| 122 | W I R I N G |
| 123 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 124 | Group B |
| 125 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 126 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 127 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 128 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 129 | Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required. |
| 130 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 131 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 132 | Upto 450 mm sweep |
| 133 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 134 | MCCB, MCB & DB’S |
| 135 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 136 | 4 way (4 + 12), Double door |
| 137 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 138 | Single pole |
| 139 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 140 | 100 amps |
| 141 | MV CABLE LAYING |
| 142 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. |
| 143 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 144 | Non Schedule items |
| 145 | Supply of Led battan 20 watt Surface mounted SILM LINE NEXT.philips make or Eqiuvalent as approved By Engineer Incharge |
| 146 | Supply of 10W Bulk Head Light Philips / WIPRO/ havells MAKE or Eqiuvalent as approved By Engineer Incharge |
| 147 | Supply of Crompton Greaves Trans Air 300 mm Exhaust Fan CROPTON MAKE OR or Eqiuvalent as approved By Engineer Incharge |
| 148 | Supply at site 1.1 KV grade XLPE insulated of size 4 X 25 Sq.mm aluminium armoured.cable Gloster/Havells/Skytone/ RR , Make or Eqiuvalent as approved By Engineer Incharge |
| 149 | Supply and Fixing LED Flood Light 200 watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and toughned class having bottom opening seperate driver compartment with IP66 Protection, Bajaj/Philips/ Havells /Wipro/ Crompton Make or Eqiuvalent as approved By Engineer Incharge |
| 150 | Supply and fixing of M.S 40 mm Dia Extension Pipe 1 meter Length incuding primer & paint With Fastner ,02 Nos Heavy Clamp,welding of angle 25X25X4 lengh 600 mm with holes & Suitable size for Nut Bolt etc |
| 151 | Supply and Fixing 6 Sq.mm 2 Core Flat PVC Insulated,Innersheathed, Unarmoured aluminium Cable Plaza /Havells /Polycab Make or Eqiuvalent as approved By Engineer Incharge |
| 152 | Supply and Fixing heavy Duty Plastic Cable Cleat incuding laying & fixing of suitable for Cable size etc as requried as approved By Engineer Incharge |
| 153 | Supply and fixing of site FP MCB 63 Amp C curve I/C MCB enclosure sheet steel 4 way Havells/L&T/ Schneider Make Please Enable Macros to View BoQ information |
