|
| 1 | Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineerin- charge. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 3 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 7 | 15 mm nominal bore |
| 8 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 9 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangementof approved quality and colour. |
| 10 | 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 11 | Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge. |
| 12 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 13 | Providing and Fixing of PUFF panel 40 mm thick with both sides 0.5 mm galvalume sheet material strength 550 MPa, galvalume AZ- 150 GSM (both side inclusive) with regular modified polyester paint and coating of 20-25 micron on expose surface including primer and 7-10 micron coating on un exposing surface including primer using stainless steel self driving/ taping screws of size 6 x50 mm with EPDM seal and stainless steel plain washer complete fitting (for 2 units) as per direction of Engineer in Charge. |
| 14 | Providing and Fixing of Roof PUFF panel 40#75 mm thick with both sides 0.5 mm galvalume sheet material strength 550 MPa, galvalume AZ- 150 GSM (both side inclusive) with regular modified polyester paint and coating of 20-25 micron on expose surface including primer and 7-10 micron coating on un exposing surface including primer using stainless steel self driving/ taping screws of size 6 x50 mm with EPDM seal and stainless steel plain washer complete fitting (for 2 units) as per direction of Engineer in Charge. |
| 15 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 16 | Fixing glazed/ Ceramic Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3 mm thickness. |
| 17 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. |
| 18 | Providing and fixing on wall face unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including all necessary specials and fiiting i.e bends, tees, junctions (with or without door) , reducers, WC connectors, couplers, cowels, clamps, hangers, rubber rings etc complete in all respect as per the directions of Engg-in-charge. |
| 19 | 75 mm diameter (Wall Thickness - 3.2 to 3.8 mm) |
| 20 | 110 mm diameter (Wall Thickness - 3.2 to 3.8 mm) |
| 21 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 22 | Providing and fixing PTMT grating of approved quality and colour. |
| 23 | Circular type |
| 24 | 100 mm nominal dia |
| 25 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 26 | 15mm nominal bore |
| 27 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 28 | 15 mm nominal bore |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 30 | 20 mm nominal outer dia Pipes |
| 31 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge . External work |
| 32 | 20 mm nominal dia Pipes |
| 33 | Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured). |
| 34 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 35 | 300x10 mm |
| 36 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : |
| 37 | 4.0 mm thick glass panes |
| 38 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 39 | Hot finished welded type tubes |
| 40 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 41 | 150 mm diameter |
| 42 | Providing and fixing vanity type counter-top wash basin of approved quality and make, White Vitreous China, suitable for mounting on vanity/counter, including 15 mm dia CP Brass single hole basin mixer, complete with all necessary fittings, connections, cutting and making good the walls/counter wherever required, and finishing complete as per site requirement.(a) White/Grey Vitreous China counter-top wash basin (vanity type) of approved size and make, with 15 mm CP Brass single hole basin mixer. |
| 43 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 44 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required |
| 45 | Kitchen sink without drain board |
| 46 | 470x420 mm bowl depth 178 mm |
| 47 | Providing and fixing brass bib cock of approved quality : |
| 48 | 15 mm nominal bore |
| 49 | Providing and fixing toilet paper holder : |
| 50 | C.P. brass |
| 51 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 52 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 53 | Providing and fixing in position Straight Grab Bar(Dia.38mm Length 692mm Two Wall Horizontal and Swing Up Grab Bar complete with all accessories and fitting complete as per direction of the Engineer in Charge |
| 54 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 55 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 56 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 57 | 100 mm inlet and 100 mm outlet |
| 58 | Sand cast iron S&S as per IS: 3989 |
| 59 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 60 | Providing and fixing PPR Unions |
| 61 | PPR Union 20mm |
| 62 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 63 | 30 cm length |
| 64 | 15 mm nominal bore |
| 65 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 66 | Group A |
| 67 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. |
| 68 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 69 | 2 X 4 sq. mm + 1 X 2.5 sq. mm earth wire |
| 70 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 71 | Single pole |
| 72 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 73 | 25 mm |
| 74 | Providing and fixing following rating, 20 W LED Light complete with connections,testing and commissioning etc. as required. |
| 75 | Providing and fixing 300 mm exhaust with complete installation and commissioning |
| 76 | providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubical panel,making connections,etc.as required. |
| 77 | 63 A TP&N |
| 78 | Supplying and Fixing Following way Single Pole and neutral,sheet steel,MCB distribution Board, 240V on surface/recess,complete with tinned copper bus bar,neutral bus bar,din bar,interconnections,powder painted including earthing etc.as required.(But without MCB/RCCB/Isolator) |
| 79 | 12 way , double door Please Enable Macros to View BoQ information |
