|
| 1 | B.T. RENEWAL WORK IN DIFFERENT ROADS UNDER P.W.D SUB DIVISION BANDA LANGTH 18.30 KM PAC 488.28 LAKH (GROUP-I)1. Budakhera Shahpur Road 6.30 KM, PAC 135.54 LAKH2.Banda Bandri Road KM 11 to 16, PAC 186.70 LAKH3. Banda Shahpur Parsoriya Road 6.00 KM (BT over CC) PAC 166.04 LAKH Please Enable Macros to View BoQ information Annexure- G Group- 01 NIT Schedule of 1- Budakhera Shahpur Road 6.30 KM 13553523.80625 2- Banda Bandri Road KM 11 to 16 18669788.45 3-Banda Shahpur Parsoriya Road 6.00 KM (BT over CC) 16604153.45 Total 48827465.70625 Say, Rs. 488.27 Lakh PAC Rs. 186.7 Lakhs 488.27 Lakh SCHEDULE OF RATES FOR ROAD & BRIDGE WORKS IN fORCE fROM 11.04.2025 S.No. SOR Item no./ Description of Item Bud Bandri B Shah Total Qty Unit Rate Amount in Rs |
| 2 | 3.12 Scarifying existing bituminous surface to a depth of 50 mm by mechanical means Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material with in all lifts and lead up to 1000 meters. |
| 3 | 4.3 Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density in accordance to Table No. 400-12, 400-13 and as per clause of section 406 of specifications.A By Sensor Paver |
| 4 | 5.1 Prime Coat Over WMM/WBM (i) Providing and applying primer coat with catonic bitumen emulsion on prepared surface of granular Base including cleaning of road surface and spraying primer at the rate of 0.70 to 1.00 kg/sqm using mechanical means as per clause 502 of specifications. |
| 5 | 5.3 Providing and applying tack coat with cationic bitumen emulsion using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per relevant clauses of section-503 of specifications. |
| 6 | (ii) @0.30 kg per sqm (dry & hungry bituminous surfaces /Granular surfaces treated with primer) |
| 7 | (i) @ 0.25 kg per sqm (normal bituminous surfaces) (iv) @ 0.40 kg per sqm (non-bituminous surfaces) granular base not primed 37950.0 37950.0 sqm 21.0 796950.0 |
| 8 | 10.5 Built-Up-Spray Grout Providing, laying and rolling of built-up-spray grout layer over prepared base consisting of a two-layer composite construction of compacted crushed coarse aggregates using motor grader for aggregates key stone chips spreader may be used with application of bituminous binder after each layer, and with key aggregates placed on top of the second layer to serve as a Base conforming to the line, grades and cross-section specified, the compacted layer thickness being 75 mm. |
| 9 | 5.6 Dense Graded Bituminous Macadam Providing and laying dense bituminous macadam using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a Electronic Sensor paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 505 of specification complete in all respects. b) Using Drum Mix Plant of appropriate capacity. (iv) for Grading II (26.5 mm nominal size) Bitumen Content minimum 4.5% with bitumen 60/70 (VG 30) |
| 10 | 5.7 Bituminous Concrete Providing and laying bituminous concrete using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % by weight of total mix of mix and filler, transporting the hot mix to work site, laying with an Electronic Sensor paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem and pneumatic tyre rollers to achieve the desired compaction as per clause 507 of specification. b) Using Drum Mix Plant of appropriate capacity. (v) for Grading-II (30-40 mm thickness) Bitumen Content minimum 5.4% with 60/70 bitumen (VG-30) |
| 11 | 4.16 Construction of Shoulders with approved material/selected soil i/c excavation all lifts & leads i/c grading to required slope & camber of 4% and compacting on OMC using vibratory roller of 80 to 100 kN static weight. Field compaction shall be done in corresponding layers of carriage way thickness and meet the requirements of MDD to achieve compaction (98% -100%) as per relevant clause of 408. A Hard Shoulders (CBR value >12) |
| 12 | 8.38 Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beeds on Bituminous surface. Providing and applying (Cleaning of Bituminous surface) thermoplastic compound having composition of binder (Regin) minimum 18 %, titanium dioxide minimum 10 % and intermixed glass beed, minimum 30% of brand like Asian, Burger or equivalent make of 2.5 mm thick including drop down reflectorizing, glass beeds @ 250 gms per sqm area thickness of 2.5 mm is exclusive of surface applied glass beeds as per IRC:35.The finished surface to be level, uniform and free from streaks and holes, all complete as per clause 803 ofspecifications. Note: - The guarantee of Thermoplastic should be minimum 3 Years. |
| 13 | 8.3 Retro- reflectorised Traffic signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2022 made of high intensity Micro-Prismatic Grade Sheeting (Type IV) vide IRC: 67:2022 clause 6.7.3.2 and clause 801.3.3 of MoRT &H fixed over Aluminum composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminum with overall thickness of 4mm and aluminum skin of thickness 0.3 on both side, the ACM shall conform to Table 6.1 of IRC:67:2022 and Table 800-1 of MoRT &H specification and High Intensity Micro Prismatic Grade Sheeting shall conform to Table 6.6 of IRC:67:2022 and Table 800-3 of MoRT &H specification of in the clause 6.8 of the IRC 67-2022 and clause 801.3.7 of MoRT&H message legend numerical letter etc. and borders shall be screen printed on high intensity micro prismatic sheeting shall conform to clause 801.3.7 with digital printing ink or of cutout from transparent durable overlay or cutout from the same type of reflecting sheeting for cautionary/ mandatory/ signs, supported on MS |
| 14 | sign post of size 75mm x75mm x 6mm of 3.60 meter over all length and fix to ground by means of properly designed foundation of dimension 450x450x600mm with M20 grade concrete. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts. & supported with a back-support frame of 25mmx25mmx3mm angle. 7 years warranty for Retro Reflection Sheeting to be provided from the original sheeting manufacture brand like 3M/Avery Dennison/ Orafol Make as per clause 6.9 of IRC: 67:2022 & a certified copy for three years for outdoor exposure report from an independent test lab as per clause 6.7 of IRC: 67:2022 for the product offered shall be submitted by the contractor. Note: - Manufacture name and date of manufacture is to be printed (Embossed) at the backside of the board. |
| 15 | iv) 60 cm equilateral triangle |
| 16 | viii) 60 cm circular |
| 17 | x) 80 cm x 60 cm rectangular |
| 18 | 8.7 Direction and Place Identification signs more than 0.9 sqm size board.Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2022 made of high intensity Micro-Prismatic Grade Sheeting (Type IV) vide IRC: 67:2022 clause 6.7.3.2 and clause 801.3.3 of MoRT&H fixed over Aluminum composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminum with overall thickness of 4mm and aluminum skin of thickness 0.3 on both side, the ACM shall conform to Table 6.1 of IRC:67:2022 and Table 800-1 of MoRT&H specification and High Intensity Micro Prismatic Grade Sheeting shall conform to Table 6.6 of IRC:67:2022 and |
| 19 | Table 800-3 of MoRT&H specification of in the clause 6.8 of the IRC 67-2022 and clause 801.3.7 of MoRT&H message legend numerical letter etc. and borders shall be screen printed on high intensity micro prismatic sheeting shall conform to clause 801.3.7 with digital printing ink or of cutout from transparent durable overlay or cutout from the same type of reflecting sheeting for cautionary/ mandatory/ signs, supported on 2 nos. of MS sign post of size 75mm x75mm x 6mm of 3.60 meter over all length and fix to ground by means of properly designed foundation of dimension 450x450x600mm with M20 grade concrete. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts. & supported with a back-support frame of 25mmx25mmx3mm angle. 7 years warranty for Retro Reflection Sheeting to be provided from the original sheeting manufacture brand like 3M/Avery Dennison/ Orafol Make as per clause 6.9 of IRC: 67:2022 & a certified copy for three years for outdoor exposure report from an independent test lab as per clause 6.7 of IRC: 67:2022 for the product offered shall be submitted by the contractor.Note: - Manufacture name and date of manufacture is to be printed (Embossed) at the backside of the board. |
| 20 | 8.22 Road DelineatorsSupplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and confirming toIRC-79 and the drawings. |
| 21 | 8.23 Road Markers/Road Stud with Lense ReflectorProviding and fixing single mound twin shanked molded Road Markers/Road Stud made of poly carbonate or ABS body and shall support a load of 13635 Kg tested in accordance to ASTM D 4280 and complying lo specifications of Section-5 of IRC:35-2015 and clause 804.2.2 of MORT&H and Section-5 of IRC:35-2015. he reflecting panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face. The slope or retro-reflecting surface should be 35 + 5 degree to base. The reflective marker shall be fixed to the road surface using the epoxy/ adhesives and the procedure recommended by the manufacturer. No nails shall be used to affix the markers so Cubes capable of that they do not pose safety hazard on the road. The contractor shall submit a two-year replacement warranty. for satisfactory field performance including stipulated retro-reflectance of the reflecting panel. (Make- 3M /AVERY DENNISON/ ORAFOL / ALCOLITEA / AUTOMARK) |
| 22 | 8.36 Kilo Metre Stone Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc (i) 5th kilometre stone (precast) 1.0 1.0 1.0 3.0 Each 3686.0 11058.0 (ii) Ordinary Kilometer stone (Precast) 3.15 3.0 3.0 9.15 Each 2131.0 19499.0 (iii) Hectometer stone (Precast) 18.9 18.0 18.0 54.9 Each 621.0 34093.0 |
| 23 | 8.17 Metal Beam Crash BarrierA Type - A, \\"W\\" : Metal Beam Crash Barrier (Providing and erecting a \\"W\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, however 5 spaces of 600mm each between vertical post and 5 spaces of 900mm each between vertical post will be kept adjacent to RCC parapet/ concrete crash barrier in accordance to figure 9.14 of the IRC-SP: 73-2018, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811) and treatment for metal beam cresh barrier on approach shall be modified eccentric loader terminal arrangement as shown in figure 9.12 of IRC- SP : 73-2018 End portion of metal beam crash barrier shall be flared outside by 1.25 mtr. Distance in last section of 8 mtr. Length. Departure side it shall be trailing terminal (TT) arrangement as shown in figure 9.13 of the IRC SP-73-2018. End portion of metal beam crash barrier shall be flared outside by 0.35 mtr. Distance in last section of 8 mtr. Length Total 48827511.0 Subdivisional Officer Executive Engineer PWD Sub Dn Banda PWD Division No-01 Sagar |
