|
| 1 | Labour Charge for lifting of 20000 / 15000 / 10000 / 7500 / 5000 / 2500 GPH capacity water vertical submerssible pump with motor sets including column pipes assembly by heavy duty chain pully block as per direction of the Engineer-in-charge. |
| 2 | Labour Charge for fitting, fixing and lowering of 20000 / 15000 / 10000 / 7500 / 5000 / 2500 GPH capacity water vertical submerssible pump with motor sets including column pipes assembly by heavy duty chain pully block as per direction of the Engineer-in-charge. |
| 3 | Supplying of 5000 GPH x 76 mtrs. Head water lubricated submersible pump of maximum 150 mm outer dia. With maximun 10 (ten) stages coupled with required wet and non-cover loading submersible motor suitable for 340-440 volts, 3 phase 50Hz, A.C. Supply and star delta method of starting along with 35 mtrs. x 2 x 3 x 4 sq.mm joint less PVC 3 (Three) core double length flat cable (continuous length) of suitable size fitted with submersible motor, suction case, strainer, coupling key, vertical non- return valve cum discharge case including supplying of 10 Nos. suitable cable guard with clips & nuts & bolts, 2 (two) pair M.S. column clamps as per direction of Engineer-in-charge conforming to terms & conditions of the contract. (Each pump with motor shall consists of stainless stell closed type impeller , C.I. bowl, C.I discharge case, pump shaft (styainless steel), bush (bronze), shaft sleeve (bronze/chromium), sand guard, winding rotor, stator, counter thrust plate, thrust plate, thrust bearing segment etc. conforming to relevant BIS codes). |
| 4 | Supplying of 7500 GPH x 76 mtrs. Head water lubricated submersible pump of maximum 150 mm outer dia. With maximun 10 (ten) stages coupled with required wet and non-cover loading submersible motor suitable for 340-440 volts, 3 phase 50Hz, A.C. Supply and star delta method of starting along with 35 mtrs. x 2 x 3 x 4 sq.mm joint less PVC 3 (Three) core double length flat cable (continuous length) of suitable size fitted with submersible motor, suction case, strainer, coupling key, vertical non- return valve cum discharge case including supplying of 10 Nos. suitable cable guard with clips & nuts & bolts, 2 (two) pair M.S. column clamps as per direction of Engineer-in-charge conforming to terms & conditions of the contract. (Each pump with motor shall consists of stainless stell closed type impeller , C.I. bowl, C.I discharge case, pump shaft (styainless steel), bush (bronze), shaft sleeve (bronze/chromium), sand guard, winding rotor, stator, counter thrust plate, thrust plate, thrust bearing segment etc. conforming to relevant BIS codes). |
| 5 | Installation of submerssible pump and suitable motor upto required depth with GI column pipe in/c providing fitting fixing by necessary rubber washer, nuts & bolts, MS safety clamp etc. as per required size and making necessary electrical connection with main switch / starter with motor in/c commissioning & trial run as per direction of the Engineer-in-charge ( pump, motor with cable, GI pipe will be issued by the Department at free of cost and fabrication of GI column pipe will be paid separately ). |
| 6 | i. 5000/7500 GPH Capacity |
| 7 | Providing and fitting fixing with PVC insulated 3 core flat Copper cable conforming to relevant IS code for submerssible motor with all necessary equipments and fittings as required as per specification and direction of the Engineer-in-charge. |
| 8 | i) 6.0 sqmm |
| 9 | ii) 10.0 sqmm |
| 10 | Providing earthing with perforated 40 mm dia G.I. pipe (Medium class) ( 12 mm dia perforation ) , laying of 4 mm dia GI wire from earth electrode to panel, including excavating hole of 600 mm dia and refilling with Salt and Charcoal / coke in alternate layers of 300 mm , as per standard specification and direction of the Engineer-incharge. |
| 11 | i) for 3-phase connection with 4.00 mtr. Long G.I. pipe |
| 12 | Providing and fixing of well cap ( made with 8 mm thick MS sheet ) by welding with blind pipe including applying of anticorrusive bitumastic paint as per specification ( IS : 2800 (part- I) and direction of the Engineer - in - charge. |
| 13 | i) for 200 mm dia ERW pipes |
| 14 | Supplying and fitting fixing of following spare parts of approved quality suitable for submersible pump and motor etc. as per direction of the Engineer-in-charge. a) Full threaded nut and bolts 50 mm long. |
| 15 | Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 16 | i) 100 mm dia |
| 17 | ii) 80 mm dia |
| 18 | iii) 65 mm dia |
| 19 | Making and supplying fitting fixing of MS clamp of size 200 X 250 X 150 mm with nuts, bolts complete as per direction of the Engineer-in-charge. |
| 20 | Charges for making G.I. tail piece with MS flange ( 8 mm wall thickness ) at one end & threading at other end in/c. cutting, threading, welding & fitting, fixing as per specification and the direction of the Engineer-in-charge. ( G.I. pipes will be supplied from the department free of cost ). |
| 21 | i) 100 mm dia |
| 22 | ii) 80 mm dia |
| 23 | iii) 65 mm dia |
| 24 | Providing & fabrication of column pipe including fitting fixing of G.I. flange by cutting the GI pipe ( conforming to IS : 1239 medium class ) into 3.05 mtr. long and welding the same with GI flange as per specification and direction of the Engineer-in-charge ( G.I. pipe will be provided by the agency at his own cost & risk). |
| 25 | i) For 65 mm dia G.I. pipe with 10 mm thick GI flange |
| 26 | ii) For 80 mm dia G.I. pipe with 10 mm thick GI flange |
| 27 | iii) For 100 mm dia G.I. pipe with 10 mm thick GI flange Please Enable Macros to View BoQ information |
