|
| 1 | S & F Compactor for 3(I) Armd Bde Provost Unit overall dimension of the Puslh Pull Optimizer inclduing clhannels (2047H x3600W x 400D) MM.The Construction shall be rigid knock cown made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus add on units (1,2,3,4,5). Finish shall be Epoxy polyester powder coated thickness of 40 microns.Shelf constıruction shall be made fron CRCA steel0.7 mm thick IS :513 .Uniformly distributed load capacity of 60 Kg.Undercarriage shall have construction in welded fiame CRCA sheet 2 mmthk conforming to IS:513.The movements of the system slhall be Puslh pull configuration (TYPE-P1/TYPE-P2) : Moveinent of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels.The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. ofa special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, ie. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned.The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level.The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized /blackodized /Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion.The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. // When the last unit is twin movable, hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto twin unit. . |
| 2 | S & F Compactor for Stn HQ,Ratnuchak overall dimension of the Push Pull Optimizer inclduing channels (2047H x 3200W x 400D) MM.The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513.Each body shall have a main unit plus add on units (1,2,3,4,5). Finish shall be Epoxy polyester powder coated thickness of 40 microns.Shelf construction shall be made from CRCA steel 0.7 mm thick IS :513 Uniformly distributed load capacity of 60 Kg.Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513.The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels.The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned.The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level.The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminiun extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion.The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. // When the last unit is twin movable, hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto twin unit. |
| 3 | S & F Compactor for HQ 3(I) Armd Bde (Q BR)overall dimension of the Push Pull Optimizer inclduing channels (2047H x 6000W x 400D) MM.The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS: 513.Each body shall have a main unit plus add on units (1,2,3,4,5). Finish shall be Epoxy polyester powder coated thickness of 40 microns.Shelf construction shall be made from CRCA steel 0.7 mn thick IS :513 Uniformly distributed load capacity of 60 Kg .Undercarriage shall have construction in welded frame CRCA slieet 2 mmthk conforming to IS:513.The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2): Movement of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movble units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos, of antifriction bal bearings for rolling on channels.The twin moving body, i.e. TM, has 4 nos, of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body,.which not only restricts lateral moveent but also prevents SL fron tojPping h Centralized locking arrangement is provided throtugh Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned.The Recess handle lock is of Godrej make & placed at a heiglht of 940mim from ground level.The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, itted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion.The length of paper is 394m for LD/SD and 794mm for TD. 0ver that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. // When the last unit is twin movable , hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto twin unit. |
| 4 | S & F Compactor for 3(I) Armd Bde (G BR) overall dimension of the Push Pull Optimizer inclduing channels (2047Hx 4800W x 400D) MM.The Construction shall be rigid knock down made out of0.8 thick CRCA steel conforming to IS : 5 13.Each body shall have a main unit plus add on units (1,2,3,4,5). Finish shall be Epoxy polyester powder coated thickness of 40 microns.Shelf construction shall be made from CRCA steel 0.7 mm thick IS :513 Uniformly distributed load capacity of 60 Kg.Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:5 13.The movements of the system shall be Push pull configuration (TYP5-P1/TYPE-P2): Movement of units achieved by pushing or pulling 'C tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball be arings for rolling on channels.The twin moving body, ie. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, ie. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movenment but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stifener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned.The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level.The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized/ blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion.The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. // When the last unit is twin movable , hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto twin unit. |
| 5 | S & F Compactor for 3(I0 Armd Bde Sig Coy overall dimension of the Push Pull Optimizer inclduing channels (2047Hx 4800W x 400D) MM.The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS: 513.Each body shall have a main unit plus add on units (1,2,3,4,5). Finish shall be Epoxy polyester powder coated thiclness of 40 microns.Shelf construction shall be made from CRCA steel 0,7 mm thick IS :513 .Uniformly distributed load capacity of 60 Kg.Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513.The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2): Movement of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels.The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral ınovement of the body on rail while the single moving body, ie. SL, body has 2 nos. ofa special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, ie. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned.The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level.The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized/ blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396m for LD/SD and 796mm for TD, fitted on to front cover of body, The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminiunn extrusion.The length of paper is 394mm for LD/SD and 794mim for TD, 0ver that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. J/ When the last unit is twin movable, binged doors are provided for the end bodies, So in this case locking stiffener is mounted onto twin unit. Please Enable Macros to View BoQ information |
