|
| 1 | Dismantling/Fitting of Engine Head safely by manual/mech. means, etc for inspection/repairs. |
| 2 | Top overhauling of the engine. The job includes inspecting the cylinder head & allied parts, repairing/replacement of damaged/worn out components, machining of the engine head, cleaning the chamber, checking & cleaning nozzles, p/f of piston rings, tappet springs, head gasket, valve seats and allied items/works. Job includes assembling the engine head, draining of old m.oil and filling of fresh m oil and testing the performance on full load. |
| 3 | Lifting of Engine Block safely from the vehicle by hyd. crane /mech. means, etc and safe lowering to work surface for inspection or repairs & fitting the engine back to vehicle after completion of the work. |
| 4 | General overhauling of the engine. The job includes lifting of Engine Block safely from the vehicle by way of hyd. crane /hoist, etc and safe lowering to work surface. Dismantling the various components of the engine (cylinder head, connecting rod, crankshaft, pistons, etc) and allied parts completely for inspection and repairs. Replacement of worn out/damaged components/ parts which include pistons with ring sets, valve sets, valve guide sets, gudgeon pin set, bearing set, big end bearing set, sleeve sets, head gasket, packing set, etc repairing, machining and cleaning the necessary components by skilled labour. Assembling the components/parts of engine job includes draining of old m. oil and filling of fresh m. oil, safely lifting & mounting of engine back to engine enclosure/ fitting the engine back to vehicle and testing the performance of engine on full load. The job incl. allied works & other allied charges. |
| 5 | Providing/fitting of Engine Head |
| 6 | P/F of Piston Set |
| 7 | P/F of Piston Ring Set |
| 8 | P/F of Engine head gasket |
| 9 | Engine head machining |
| 10 | P/F of Valve Set |
| 11 | P/F of Valve Guide Set |
| 12 | P/F of Connecting Rod |
| 13 | P/F of Main Bearing Set |
| 14 | P/F of Big End Bearing inst. |
| 15 | P/F of Sleeve Set |
| 16 | P/F of Packing Set |
| 17 | Providing/fitting of Oil pump assembly |
| 18 | Providing/fitting of Water body complete assembly |
| 19 | Providing/fitting of M.oil plug |
| 20 | Providing/fitting of Temperature plug |
| 21 | P/F of connecting rod bush |
| 22 | Providing/fitting of Water body pulley as per sample/req. |
| 23 | Providing/fitting of Water body gasket as per sample/req. |
| 24 | P/F of Silicon Sealant/ Bonding Tube |
| 25 | P/F of Crank Oil seal |
| 26 | P/F of Main Oil seal |
| 27 | P/F of Air Compressor (Bearing, Ring Set) |
| 28 | P/F of Head Cap Oil seal |
| 29 | P/F of Tappet Cover gasket |
| 30 | P/F of Fan Belt |
| 31 | P/F of Oil Jet Pipe |
| 32 | P/F of Pulley Crank shaft |
| 33 | P/F of fan Pulley |
| 34 | P/F of fan |
| 35 | P/F of Fan Spacer |
| 36 | P/F of Alternator fan |
| 37 | P/F of Alternator Pulley |
| 38 | P/F of Switch Engine Oil Pressure |
| 39 | P/F of Rubber Mounting for cabin |
| 40 | P/F of Switch Engine Oil temperature |
| 41 | P/F of Ignition switch with key |
| 42 | Servicing of Fuel pump and allied works |
| 43 | Injector checking using Diesel fuel injector |
| 44 | Calibration using CRI tester machine |
| 45 | P/F of Nozzle washer |
| 46 | Complete Overhauling / calibration of FI Pump with P/F of required parts i.e., Nozzle, Vane Pump, TD Piston, Oil Seal, Cross Disc, etc. |
| 47 | P/F of Nozzle |
| 48 | P/F of F.I pipe |
| 49 | P/F of Diesel return pipe |
| 50 | P/F of Rotary Pump Unit |
| 51 | P/F of Cam Plate |
| 52 | P/F of Oil Seal |
| 53 | P/F of T.D Piston |
| 54 | P/F of Cross Disc |
| 55 | P/F of D.P Head |
| 56 | P/F of V.E Pump Repair Kit |
| 57 | P/F of Exhaust Pipe |
| 58 | P/F of Tail Pipe |
| 59 | P/F of Extension Pipe |
| 60 | P/F of Muffler/Main Body |
| 61 | P/F of silencer Assembly |
| 62 | P/F of Silencer Clamps set |
| 63 | P/F of Silencer Joint |
| 64 | P/F of Silencer Hanger |
| 65 | P/F of Silencer Gas Welding and Patching |
| 66 | P/F of Sprocket |
| 67 | P/F of Chain |
| 68 | P/F of Idler gear |
| 69 | P/F of Gasket |
| 70 | P/F of flywheel |
| 71 | P/F of Cooler |
| 72 | P/F of Water Pump |
| 73 | P/F of Cam Shaft |
| 74 | Service of Radiator using chemical cleaning |
| 75 | P/F of Thermostat |
| 76 | P/F of Thermostat Adapter |
| 77 | P/F of Temperature Sensor switch |
| 78 | P/F of drain cap |
| 79 | P/F of hose Pipe with clamp |
| 80 | P/F of Radiator Cap |
| 81 | P/F of Jubilee Clip |
| 82 | P/F of Air Con Assy. |
| 83 | P/F of Condenser |
| 84 | P/F of Drier |
| 85 | P/F of Radiator tank |
| 86 | Repairs/soldering to fin and radiator tanks |
| 87 | P/F of Radiator Foundation |
| 88 | P/F of Radiator Foundation bolt |
| 89 | P/F of New Radiator Complete |
| 90 | Overhauling of Turbo Charger |
| 91 | P/F of gasket |
| 92 | P/F of Stud |
| 93 | P/F of Adapter |
| 94 | P/F of Turbo Core Assembly |
| 95 | P/F of Turbo charger kit |
| 96 | P/F of Replacement of turbo charger complete |
| 97 | P/F of Turbo Hose |
| 98 | P/F of Exhaust Pipe |
| 99 | D/F of gear Box |
| 100 | P/F of Dowel pin |
| 101 | P/F of Screw |
| 102 | P/F of O-ring |
| 103 | P/F of Spring GB |
| 104 | P/F of Venting Valve |
| 105 | P/F of Breather |
| 106 | P/F of grease nipple |
| 107 | P/F of Gasket |
| 108 | P/F of Pressure relief Valve |
| 109 | P/F of Check Valve |
| 110 | P/F of Needle Sleeve |
| 111 | P/F of Clutch Disc |
| 112 | P/F of Cylindrical bearing |
| 113 | P/F of Snap ring |
| 114 | P/F of Spring set |
| 115 | P/F of Retaining Ring |
| 116 | P/F of Centering ring |
| 117 | Replacement of Front Tyre of required size (12.5/80-18 as per sample size) |
| 118 | Replacement of Rear Tyre of required size (14.00 -25 as per sample size) |
| 119 | Repairing of Mud guard |
| 120 | P/F of Tyre Valve |
| 121 | P/F of Bolt and nut Assy. |
| 122 | P/F of Knuckle Swivel Joint |
| 123 | P/F of Tie Rod Link |
| 124 | D/F of Steering System |
| 125 | P/F of Trunnion |
| 126 | P/F of Steering Bearing |
| 127 | P/F of Seal |
| 128 | P/F of Shaft Drive Assy. |
| 129 | P/F of Yoke Double |
| 130 | P/F of Spider Kit |
| 131 | P/F of Brake Plate-Counter |
| 132 | P/F of Brake Plates-Friction/Pressure |
| 133 | P/F of Yoke Flange |
| 134 | P/F of Yoke |
| 135 | P/F of end cap kit |
| 136 | P/F of U-J Cross |
| 137 | P/F of Shaft |
| 138 | Machining of Shaft |
| 139 | P/F of cross holder |
| 140 | Overhauling of Differential Assy and replacement of parts and allied work |
| 141 | P/F of side diff. Nut |
| 142 | P/F of Spacer Kit |
| 143 | P/F of Shim Kit |
| 144 | P/F of Pin |
| 145 | Providing of Bush |
| 146 | Providing of Washer |
| 147 | Providing of Nut |
| 148 | Providing of Bolt |
| 149 | Dismantling /fitting of Differential system |
| 150 | P/F of Crown Wheel Pinion with nut |
| 151 | P/F of Pinion Bearing |
| 152 | P/F of Pinion |
| 153 | P/F of Ring Gear |
| 154 | P/F of Differential Side Gear (star) with allied parts. |
| 155 | P/F of Spider lock |
| 156 | P/F of Star Kit with allied accessories complete |
| 157 | P/F of Differential Cage |
| 158 | P/F of Differential Stud |
| 159 | P/F of Star washer Set (Brass) |
| 160 | P/F of Star washer Set (Steel) |
| 161 | P/F of Differential Joint |
| 162 | P/F of Main Oil Seal |
| 163 | P/F of Planet Gear |
| 164 | P/F of Sun gear |
| 165 | P/F of Roller Bearing |
| 166 | P/F of Circlip |
| 167 | P/F of Carrier |
| 168 | P/F of Axle Arm Kit |
| 169 | D/F of Wheel Hub |
| 170 | Greasing of Wheel hub |
| 171 | P/F of Oil Filter |
| 172 | P/F of Air Filter |
| 173 | P/F of Coolant |
| 174 | P/F of Fuel Filter (Primary) |
| 175 | P/F of Fuel Filter (Secondary) |
| 176 | P/F of Hydraulic Oil |
| 177 | P/F of Breather |
| 178 | P/F of Transmission Filter |
| 179 | P/F of sucker strainer |
| 180 | P/F of Transmission Oil |
| 181 | P/F of Rear Axle Oil |
| 182 | P/F of M.Oil |
| 183 | Cleaning of Air Chamber/filter and allied parts |
| 184 | P/F of Main Fuel Pipe Set |
| 185 | P/F of Connector |
| 186 | P/F of Set Screw |
| 187 | Overhauling of Pump with motor section incl. allied works and replacement of parts. |
| 188 | P/F of Plug |
| 189 | P/F of Gear Unit of Pump Drive |
| 190 | P/F of Proportional reducing of Valve |
| 191 | P/F of Main Pump Kit Seal |
| 192 | P/F of piston repair |
| 193 | P/F of Cap Screw |
| 194 | P/F of Coupling Assy. |
| 195 | P/F of Hyd. Pipe (1”), 1 to 1.5 mtr |
| 196 | P/F of Hyd. Pipe (1”-1.5”), 1 to 2 mtr |
| 197 | P/F of Hyd. Pipe (0.5”), upto 1 mtr |
| 198 | P/F of main hyd. Pipe as per sample |
| 199 | P/F of transmission pipe as per sample |
| 200 | P/F of Switches |
| 201 | P/F of transmission Control Valve |
| 202 | P/F of Clamp |
| 203 | P/F of Cap Screw |
| 204 | P/F of Sleeve |
| 205 | P/F of Solenoid valve |
| 206 | P/F of Feed pipe |
| 207 | P/F of Socket |
| 208 | P/F of hand Controller valve |
| 209 | P/F of Relief valve |
| 210 | P/F of Coupling |
| 211 | P/F of Pilot shuttle valve |
| 212 | P/F of Steering valve |
| 213 | P/F of control Valve Assy. with allied work |
| 214 | Dismantling of all hydraulic linkage system |
| 215 | Dismantling of exhaust system |
| 216 | p/F of common spool kit |
| 217 | P/F of gasket allied |
| 218 | P/F of Air Pressure Sensor |
| 219 | P/F of Water Pump Sensor |
| 220 | P/F of Oil Pressure Sensor |
| 221 | P/A of Sensor Spray |
| 222 | Overhauling of Self Stater |
| 223 | P/F of Self Lock set |
| 224 | P/F of Self Stater Motor/Armature |
| 225 | P/F of Holder bursh |
| 226 | P/F of Carbon Brust set |
| 227 | P/F of Solenoid |
| 228 | P/F of Self-bush set |
| 229 | P/F of Self housing |
| 230 | P/F of Self Bearing |
| 231 | P/F of Complete Self Starter Assembly |
| 232 | P/F of selfbendex drive |
| 233 | P/F of Self-clutch fork |
| 234 | Servicing of Alternator |
| 235 | P/F of Regulator |
| 236 | P/F of Rectifier |
| 237 | P/F of Condensor |
| 238 | P/F of Rectifier plate |
| 239 | P/F of Field coil set |
| 240 | P/F of Carbon Brush Set |
| 241 | P/F of Cut out |
| 242 | P/F of Commutator switch set |
| 243 | P/F of Armature Assembly |
| 244 | P/F of Bearing |
| 245 | P/F of Hand Controller Knob |
| 246 | P/F of Brake pedal Assy. |
| 247 | P/F of Accelerator Pedal Assy. |
| 248 | P/F of Accelerator Cable |
| 249 | P/F of Steering Coloum/Shaft |
| 250 | Providing of Strut |
| 251 | P/F of Switches |
| 252 | P/F of Head Light Assy. |
| 253 | P/F of Bulb |
| 254 | P/F of Fog light |
| 255 | P/F of back Light |
| 256 | P/F of Indicator Assy. |
| 257 | P/F of Cabin Switch |
| 258 | Replacement of Fuse |
| 259 | Replacement of Main Fuse |
| 260 | P/F Horn Thimble and bolt |
| 261 | P/F of Relay_24V |
| 262 | P/F of Tie Cable |
| 263 | P/F of Convertor_24V to 12V |
| 264 | P/F of EMS Monitor Unit |
| 265 | P/F of ECM Unit |
| 266 | P/F of Batterylead set 02 Nos |
| 267 | P/F of Battery acid |
| 268 | P/F of Battery terminal |
| 269 | Providing of Battery Thimble |
| 270 | P/F of wires (as per sample). |
| 271 | Replacement of Old worn out/damaged wiring set |
| 272 | P/F of New Horn Assembly Double |
| 273 | P/F of Combination Switch |
| 274 | P/F of Complete Dash board cluster |
| 275 | P/F of Wiper blade machine |
| 276 | Vehicle scanning using engine analyzer |
| 277 | Soldering to Connection |
| 278 | P/F of Tape Roll |
| 279 | P/F of Main Line Switch |
| 280 | P/F of Cabin Switch |
| 281 | P/F of Reverse Plug |
| 282 | P/F of Fuse Box |
| 283 | P/F of Windshield glass |
| 284 | P/F of Side Glass |
| 285 | P/F of Rear Glass |
| 286 | P/F of Mirror |
| 287 | P/F of Mirror Arm Mounting |
| 288 | P/A of Adhesive |
| 289 | P/F of Wiper Blade |
| 290 | P/F of Wiper Motor |
| 291 | P/F of Hinge |
| 292 | Repairing of Door |
| 293 | P/F of Door Lock |
| 294 | Fabrication of Key |
| 295 | P/F of Door Strut |
| 296 | P/F of Door handle |
| 297 | Fabrication of Seat by removing old form and installing new form with seat Cover |
| 298 | Fabrication of Seat Cover |
| 299 | Repairing of Seat Swing Mechanism |
| 300 | Greasing of Seat Swing Mechanism |
| 301 | P/F of Cab Rubber Mounting |
| 302 | Denting/Patching/Welding of diesel fuel tank |
| 303 | P/F of hydraulic Tank Cap |
| 304 | P/F of Tank Key |
| 305 | P/F of Strainer (TansmissionStariner) |
| 306 | P/F of Strainer (Hydraulic Stariner) |
| 307 | Repairing ofStabliser |
| 308 | Repairing ofStabliser Foot |
| 309 | Repairing of Stabliser Cap |
| 310 | P/F of Stabliser Foot |
| 311 | Replacement of BJ seal kit |
| 312 | Replacement of stabilizer kits |
| 313 | Replacement of Pad set for stablizers |
| 314 | Dismantling/Fitting of KPC unit |
| 315 | Complete Overhauling of KPC unit and allied works with replacement of damaged parts |
| 316 | P/F of hyd. Cylinder Assy. set |
| 317 | P/F of Hydro Clamp |
| 318 | P/F of Boom Stopper |
| 319 | P/F of Boom Locker |
| 320 | P/F of Shim |
| 321 | P/F of Bolt and nut assy. |
| 322 | P/F of Ram Valve |
| 323 | P/F of hose burst Valve |
| 324 | P/F of Collor |
| 325 | P/F of Ring Lock |
| 326 | P/F of Dipper Ram |
| 327 | P/F of Boom Ram |
| 328 | P/F of Arm Ram |
| 329 | Repairing of Ram |
| 330 | P/F of boom seal kit |
| 331 | Repairing of Dipper |
| 332 | Repairing of Boom |
| 333 | P/F of Bucket tooth |
| 334 | P/F of tooth adapter |
| 335 | P/F of Tooth point |
| 336 | P/F of Locking Pin |
| 337 | P/F of Plough nut |
| 338 | P/F of Loader Bucket kit |
| 339 | Repairing of Bucket |
| 340 | P/F of Pin-Bush Set |
| 341 | P/F of King Pin Bushing set |
| 342 | Repairing of Tipping link |
| 343 | Repairing of Tipping lever |
| 344 | P/F of Ball Joint (Loader/Axle/Stabliser) |
| 345 | P/F of O-Ring Seal |
| 346 | Complete washing and servicing of excavator/loader incl. cleaning of internal and external surfaces, arms, boom, etc using HSD. |
| 347 | P/F of hood cover lock |
| 348 | P/F of digital/anal. meters |
| 349 | P/F of grease in parts/components of machine |
| 350 | Lubrication and greasing of machinery parts, bearings, hub, wheels, linkages, arms, pivot joints, pins, bucket joints, etc by providing AP3, EP/MP Grease/as recommended by OEM by using grease gun and other tools.(Castrol/ HPCL/ BPCL/ Caltex or eqv.) |
| 351 | Providing of stop cable |
| 352 | P/F of engine block plug with sealant |
| 353 | P/F of Brake master cylinder |
| 354 | P/F of Brake Oil (Dot4) |
| 355 | Draining/Cleaning of Hydraulic tank |
| 356 | Draining/Cleaning of Fuel Tank |
| 357 | P/T of wheel spindle and Jack rod (SS). |
| 358 | PUCC testing charges for six month |
| 359 | Misc. |
| 360 | Checking, testing and calibration of Hydraulic control valve including removal, cleaning and its fitting. |
| 361 | General Testing/checking of excavator/loader. The job includes testing of Electrical System, dismantling, testing and assembling of Hydraulic system/Mechanical system and allied works. |
| 362 | Tyre puncture repair (Front) |
| 363 | Tyre puncture repair (Rear) |
| 364 | P/F of Radiator Fan |
| 365 | P/F of Radiator Coolant Tank Please Enable Macros to View BoQ information |
