|
| 1 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). DSR No. 21.18, |
| 2 | Supplying and fixing new wooden fillets wherever necessary: 2nd class teak wood fillets. (DSR No- 14.8.1) |
| 3 | Providing and fixing Zinc Aldrop size 16mm 10\\" with screws & AB Finsh etc. complete. Rs. 1440/1.18= 1220 |
| 4 | Providing and fixing Zinc Handle (F/S) Size-125mm with necessary screws etc. complete. Rs. 360/1.18= 305 |
| 5 | Providing and fixing Zinc ZS 13 - Kick Down Door Stopper with rubber cushion, necessary screws etc. to suit shutter thickness complete. Rs. 430/1.18= 364 |
| 6 | Three Tack Three Panels Sliding window with two glazed & One wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R23 series with frame (98mm & above) x(40mm & above)& both glazed and fly screen sadh (30mm & above) X (55mm & above) with zinc aloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m) DSR No. 9.147.A4.2, |
| 7 | Removing synthetic enamal paint on door window/ventilators by scrapping/burning/granding and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 8 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficientdrying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) DSR No-13.116 |
| 9 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen plateform, vanity counter, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 Cement: 4coarse Sand) Joints treated with white cement mixed with matching pigment epoxy touch ups, including rubbring, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any Colour and shade Area of slab over 0.50 sqm. DSR No. 8.2.2.2 , |
| 10 | Providing & Fixing UV Stabilised Fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia, G.l. plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovings incorporating minimum 0.3%, ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air Pockets and shall Conform to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5'' or 4.2'' or 6'') or step-down (2'' or 3'' or 6'' ) as Specified. DSR No. 12.47.1, |
| 11 | Structual Steel work riveted bolted or welded in built up section, trusses, Builds up gates, framed work lncluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR N0-10.2, Please Enable Macros to View BoQ information |
