|
| 1 | Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness, (below or above ground level), complete all as specified and as directed. |
| 2 | Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc., complete all as specified and as directed. |
| 3 | Dismantling of stone slabs and tiles laid dry or laid dry and pointed of any description or thickness in floors,aprons etc., complete all as specified and as directed. |
| 4 | M & L for Walling of squared rubble,regular coursed, well bonded,bedded and solidly hearted masonary built in CM 1:6 including hammer dressing and Demolition of brickwork or stone/ boulder masonry all as specified and directed. |
| 5 | All as per above Item No 3 but except material , complete all as specified and directed. |
| 6 | M&L for raised pointing to rubble or polygonal rubble, uncoursed or brought up to coarse with CM 1:3, complete all as specified and as directed. |
| 7 | Material and labour for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width Type C1 1:3:6 (20 mm graded aggregate ) and setting in mortar CM 1:6, complete. Including Demolition of brickwork or stone/ boulder masonry, complete all as specified and as directed. |
| 8 | M&L for concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation, filling and mass concrete including Demolition of Cement Concrete (unreinforced) of any description and in any position, complete all as specified and as directed. |
| 9 | Material and Labour for PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in coping, mud stops, benching, water tank platform etc.on roof, chajja weathering, slightly rounded or chamfered angles and throating etc. including necessary form work and Demolition of Cement Concrete (unreinforced) of any description, complete all as specified and as directed. |
| 10 | M & L for Rendering 15mm thick cement mortar in 1:4 on fair faces of brick work or concrete surfaces even and smoothe without using extra cement.including taking down of old existing plaster of any description, complete all as specified and as directed. |
| 11 | M & L for Rendering 15mm thick cement mortar in 1:4 on fair faces of brick work or concrete surfaces even and smoothe without using extra cement, complete all as specified and as directed. |
| 12 | M&L for preparation of new surface/undecorated surfaces of walls and applying two coats of Cement Base Paint of approved tint over a coat of priming on plastered and other surfaces with alkali resistant priming paint, complete all as specified and as directed. |
| 13 | S&F for Steel work in tubular trusses,post,purlin,rafter including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including dismantling of old steel work of any description, complete all as specified and as directed. |
| 14 | S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe 410-W (Gde E-250) quality A,complete all as specified and directed including dismantling of old steel work of any description, complete all as specified and as directed. |
| 15 | M & L for framed work such as grill, gratings, etc with ends of bars shoulderedand /or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work corn-conforming to Fe.290. Gde -E-165, complete all as specified and directed.including dismantling of old steel work of any description, complete all as specified and as directed. |
| 16 | M & L for Providing precast cement concrete type B1 1:2:4 (20mm graded aggregate) set in CM 1:4 in cover slabs (for man holes etc.) and similar articles with plain faces all as specified and as directed.including diemolition of old concrete of any description and thickness, complete all as specified and as directed. |
| 17 | M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
| 18 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed. |
| 19 | M&L for 75 mm thick cement concrete 1:4:8, type D-2 (40mm graded aggregate) as in floors,hardstanding complete all specified and directed. |
| 20 | M&L for 100 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 21 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern as per IS -15658 over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed. |
| 22 | M&L for 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colour & pattern as per IS -15658 over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting ofpaver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed. |
| 23 | M&Lfor Rubber Moulded glossy finish precast chequered cement concrete tiles 30cmx30cmx25mm thick,including 20 mm thick screed in cm(1:4),set,jointed in neat cement slurry in floors with grey pigment cement and pigments, complete all as specified and as directed. |
| 24 | M&L for 300x300x10mm/ 400x400x10 mm thick non skid parking floor glosy finish paver tiles with grey cement and pigment over and including 20 mm thick screed in cm(1:4), set joinet and pointed in neat cement slurry in floors concrete all as specified and directed. |
| 25 | M&L Preparing new steel surfaces of any description, over 10cm in width/girth, applying two coats of synthethic enamel paint over one coat of red oxide primer. |
| 26 | S&F Pre-laminated galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering in any curvature, fixed with self tapping screws as specified.including dismantling of old existing sheet of any thickness and nature, complete all as specified and as directed. |
| 27 | S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed.including dismantling of old existing sheet of any thickness and nature, complete all as specified and as directed. |
| 28 | S&F of 2mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc.including dismantling of old existing sheet of any thickness and nature, complete all as specified and as directed. Please Enable Macros to View BoQ information |
