|
| 1 | Construction of Canal at Ambalakkadavu |
| 2 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 3 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 6 | 5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 7 | 5.9.16.1:Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide |
| 8 | 5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform |
| 9 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 10 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 11 | OD1553/2025-2026:Providing and fixing 12mm thick Black Rubber Expansion Joint Filler Board as expansion joint for canal side walls |
| 12 | 13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) |
| 13 | 50.18.8.9.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC Solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 110 mm pipe 4 kgf/cm2 |
| 14 | 50.18.9.9.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2 |
| 15 | 50.18.9.22.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend |
| 16 | OD1554/2025-2026:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110 mm dia End Cap |
| 17 | Providing Pumpsets at Kakkanchal Padashekharam |
| 18 | OD5531/2025-2026:Supply, Installation, Erection, Testing, Commissioning and fitting charges for all accessories of horizontally mounted submerged Centrifugal Non clog pump set of Compact Unitary Mono-block submerged Single/multi stage,Volute type casing with suitable radial type impellers on common shaft for pump and motor ,Anti friction bearing with life time greasing, protection features with sensors to monitor temperature,Mechanical seal leakage ,etc.(The pump should be confirming to HIS/IS standards).The MOC of pump,casing-cast iron,impeller -SS CF8M,Shaft-SS- 316,Suction Strainer -SS and other as per manufactures standard.The motor should be suitable for 3 Phase,415V /-10%,50Hz /- 5%,AC supply submersible motor having Class F /H insulation, Air filled and IP-68protection confirming to IS 325 or latest standards .The pump discharge capacity of 83 cubic metre /hour against head of 42 mtrs, Approx 20HP ,Speed 2250 RPM(N) ,with 10meters of copper power cable and control cable, railing arrangement. The pump should be painted with three coats of suitable anti corrosive paint over priming coat. |
| 19 | OD5532/2025-2026:Supply and erection of 20HP Auto Transformer starter (ATS) with suitable incomer and contactors including 5 KVAR Capacitor with required indications ,metering and protections for single phasing ,overload, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board |
| 20 | OD5535/2025-2026:Supply and laying additional termination cable of 1.1Kv 3.5 core 16 sqmm Copper conductor XLPE insulated ;steel armoured UG cable as per relevant IS 7098 with support for cable |
| 21 | OD5537/2025-2026::Providing earthing as per the ISI specification with earth electrode of 2.10m class be GI pipe of dia not less than 40mm with necessary funneling arrangement with necessary masonry work and 38mm RCC cover slab for brick masonry |
| 22 | OD5538/2025-2026::Providing and fixing C.I. Non Return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 125 mm diameter Class II |
| 23 | OD5539/2025-2026:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work 125 mm dia nominal bore |
| 24 | OD5540/2025-2026:MS Flanges for 125mm pipe - Manufacturing supplying and fitting 125mm dia MS Flange having shell thickness 8mm depth 60mm with suitable bolt , 6 holes ,fixing the flange in position with required welding around the flange,pipe joint grinding for smoothing the welded portion etc. complete as directed by departments officers. |
| 25 | 18.31.2.1:Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):125 mm diameterClass I |
| 26 | OD5541/2025-2026:Supplying 2 Ton Chain pully unit with Tripod for lifting submersible motor pumpset |
| 27 | OD5542/2025-2026:Supplying 20mm steel rope TypeIndustrial grade (6×19 / FMC) for lifting pumpset Please Enable Macros to View BoQ information |
