|
| 1 | Notes: (i) The contractor or his representative shall collect daily list of complaints from MES complaint cell or from concern JE and shall attend all the complaints in the same day irrespective of number of complaints received. Contractor shall employ sufficient tradesmen accordingly as per requirement. However minimum one plumber and carpenter shall be made available throughout working hours to attend emergency complaints. The rates quoted by the contractor shall be deemed inclusive of cost against supervisor, all tradesmen / labours employed, conveyance required for collecting complaints and attending at site for all items of BOQ.(ii) Contractor shall employ skilled / experienced tradesmen and workers for execution of work. (iii) Contractor or his representative shall submit compliance report of complaints on the same day with receipt / job card duly signed by the users to concern JE. Contractor may use separate register for each category of complaints and obtain signature from users after repair / rectification of complaints received and submit the same during preparation of RARs to concern JE. (iv) All critical complaints related to water supply and complaints which posses safety hazards to occupants have to be rectified within 24 hours after receipt of complaints. In case of complaints are not rectified on same day, the contractor shall submit in writing to Engineer-in-charge with valid reasons / justifications for delay and however the same shall be rectified with in 2 working days. Otherwise a recovery of Rs 500 per complaint per day shall recovered from the contractor. (v) All unserviceable materials, debris, waste material scrap etc. obtained during repair work other than such of credit materials issued to the contractor shall be removed immediately from site and disposed off at dumping locations earmarked with in the INA premises at no additional cost to the Govt. The cost of labour, transportation etc. shall be deemed included in the rates quoted by the contractor against respective BOQ items and nothing extra shall be paid. |
| 2 | Taking down chowkats or frames of any description (wooden / aluminium / steel etc.) not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames) including making good of disturbed portions of cills / jambs complete all as specified and directed. |
| 3 | Taking down chowkats or frames of any description (wooden / aluminium / steel etc.) exceeding 1.5 Sqm but not exceeding 4 Sqm each woth shutters (without taking off shutters from the frames) ncluding making good of disturbed portions of cills / jambs complete all as specified and directed. |
| 4 | Taking down shutter of any description (wooden / Aluminium / steel etc.) not exceeding 1 Sqm each complete all as specified and as directed. |
| 5 | Taking down shutter of any description (wooden / Aluminium / steel etc.) exceeding 1 Sqm and not exceeding 2 sqm each complete all as specified and as directed. |
| 6 | Supply and fixing of powder coated aluminium frame for doors, windows, ventilators, partitions, kitchen cupboards etc. (minimum thickness of powder coating not less than 50 micron) with one or more rebates / any profile including joining cleat for fixing etc. complete all as specified and directed. |
| 7 | Supply and fixing Powder coated aluminium door shutters, of any colour (Thickness or powder coating not less than 50 micron), .aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 8 | Supply and fixing Powder coated aluminium window and ventilator shutters fixed or sliding type without sash bar, aluminium section weighing 0.55 kg/m incl necessary joining cleats rubber packing anodised aluminium snap beading screws, lockig arrangement etc. complete all as specified and directed. |
| 9 | Supply and fixing of Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium staples or beading complete all as specified and directed. |
| 10 | Supply and fixing in repair aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium staples or beading complete. |
| 11 | Hacking out old broken glass (any thickness, size, quality or description) form metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified. |
| 12 | Supply and fixing sheet glass 4mm thick, ordinary quality and glazing with glazing clips in square not exceeding 0.5 sqm in each panecomplete all as specified and directed. |
| 13 | Material & Labour 4mm thick sheet figured glass pin headed quality not exceeding 0.50 sqm in each pane and glazing with aluminium beading complete all as specified and directed. |
| 14 | Supply and fixing Aluminium composite panel 4 mm thick of approved colour and shade fixed with self tapping screws on aluminium frame work in suitable shape and size complete all as specified and directed by Engr-in-charge. Note: Aluminium frame work if required shall be measured and paid separately |
| 15 | Material & Labour solid PVC door frame of wood grain pvc of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per specification and drawings and as directed.. |
| 16 | Supply and fixing 24 mm thick factory made PVC door shutters to existing door frames made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanized/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wallthickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter) |
| 17 | M& 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, both face is covered with deco rative face veneer with lipping/frame to match supplied and fitted to chowkats complete all as specified and as directed |
| 18 | Material & Labour 40mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, both face is covered with deco rative face veneer with lipping/frame to match supplied and fitted to chowkats complete all as specified and as directed |
| 19 | Material & Labour Plain , 40mm thick framed panelled shutters(any number of panels),with panels of timber flat on both sides (feather edged), or of veneered particle board medium dencity,wood particle board with commercial face vaneers: supplied and fixed to chowkats. |
| 20 | Material & Labour for French polishing on new wooden surfaces of any description, width or girth including cleaning and preparing the surface, filling depressions / holes etc. with wood filler putty applying additional coats wherever required to achieve even shade and colour, complete all as specified and directed. |
| 21 | Supply and fixing of 100 mm size cast brass, with mild steel hinge pin, bright polished and fixed, type B-11butt hinges, cold rolled medium weight all as specified and directed |
| 22 | Supply and fixing of 100mm size medium weight ,cold rolled mild steel butt hinges all as specified and directed |
| 23 | Supply and fixing of 150 mm anodised aluminium handles cast type all as specified |
| 24 | Supply and fixing of 150 mm size Brass Extruded section handles polished bright all as specified |
| 25 | Supply and fixing of 150 mm size Aluminium anodised barrel tower bolts of extruded section |
| 26 | Supply and fixing of 150 mm size Brass extruded section barrel tower bolts with cast sheet barrel and rolled or cast bolts of extruded section |
| 27 | Supply and fixing in repairs 100 mm anodised aluminium handles cast type all as specified |
| 28 | Supply and fixing in repairs 150 mm Brass Extruded section handles polished bright all as specified |
| 29 | Supply and fixing in repairs 150 mm Aluminium anodised barrel tower bolts of extruded section all as specified. |
| 30 | Supply and fixing in repairs 150 mm Brass extruded section barrel tower bolts with cast sheet barrel and rolled or cast bolts of extruded section all as specified. |
| 31 | Supply and fixing in repairs 250 mm aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified. |
| 32 | Supply and fixing in repairs 300 mm aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified. |
| 33 | Supply and fixing in repairs 250 mm Brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bilt with roller or drawn brass bolts all as specified. |
| 34 | Supply and fixing in repairs floor door stopper 150 mm size aluminium alloy body and tongue double legged, anodised fixed to door all as specified. |
| 35 | Supply and fixing in repairs floor door stopper 150 mm size brass body and tongue double legged, anodised fixed to door all as specified. |
| 36 | Supply and fixing in repair looking mirror 600X450mm, selected quality glass mounted on 6mm thick PVC/AC building board/commercial plywood, PVC beading all round and fixed to wall complete all as specified and directed. |
| 37 | Supply and fixing in repair looking mirror of size exceeding 0.3 Sqm , selected quality glass mounted on 6mm thick PVC/AC building board/commercial plywood, PVC beading all round and fixed to wall complete all as specified and directed. |
| 38 | Supply and fixing in repair Mortise lock brass body, 100mm, 4 levers vertical type complete all as specified and directed. |
| 39 | Supply and fixing in repair 20 mm bore curtain rods, anodised aluminium alloy, PVC coated with fixing brackets, stops, rollers etc. all as specified |
| 40 | Supply and fixing in repair Venations blinds with necessary hanging arrangements and necessary fittings all as specified |
| 41 | Supply and fixing in repair aluminium (extruded section) body door closer hydraulically regulated designation No. 2 universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg all as specified |
| 42 | Supply and fixing in repair Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete |
| 43 | Dismantling timber scantling of sectional area above 40 sq. cm and over in section, in any position framed / unframed work all as specified and directed. |
| 44 | Material & Labour for Second class hard-wood in scantlings clean sawn fixed in position as required at site framed / unframed complete all as specified and directed. |
| 45 | Dismantling boarding, any description, fixed in any position with screws complete all as specified and as directed |
| 46 | Supply and fixing 12 mm thick Preleminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing with white lamination ,fixed with screws to timber frame work |
| 47 | Supply and fixing 12 mm thick Plywood grade BWR,type BB, fixed with screws to timber frame work |
| 48 | Supply and fixing 18-20 mm thick extruded polymer profile form board having density of 0.65gm/cc made of uPVC polyester resin of any colour and pattern used as in kitchen cabinets/ wardrobes/ Shutters/drawers etc. fixed with screws in required size and shape all as specified and as directed Note : Necessary fittings will be measured and paid separately under relevant items |
| 49 | Supply and fixing 18 mm thick Plywood grade BWR, type BB, fixed with screws to timber frame work |
| 50 | Material & Labour for 1.2 to 1.5mm thick glossy finish Acrylic laminate of surface finish, colour and pattern as approved, fixed with approved adhesive for fixing over BWP plywood (710 gde)/ polymer profile form board as per manufacturer's instructions complete all as specified and as directed. |
| 51 | Supply and fixing stainless steel soft closing hydraulic hinges for shutter complete all as specified and as directed. |
| 52 | Supply and fixing 125 mm stainless steel handles, cast type, polished for cupboard shutters etc. complete all as specified and as directed. |
| 53 | Supply and fixing 1stainless steel telescopic drawer channel double ball bearing complete fixed all as per manufacturers instructions and all as directed |
| 54 | Supply and fixing Brass hat & coat hooks, solid body,175mm to 250mm. |
| 55 | Supply and fixing Brass drawer handles, projection drop (50mmx65mm)on screwed plate. |
| 56 | Supply and fixing 4 Lever Brass Locks for drawer, grade I,size75mm |
| 57 | Taking down , repairing & refixing of builders hard ware items like handles, hinges, bolts, tower bolts, sliding bolt etc. using necessary screws at the same position. |
| 58 | Dismantling wall/floor and ceiling boards (fibre, pulp, insulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed |
| 59 | Material & Labour Anodised aluminium snap grid frame work fixed with minimum 2mm GI wire hangers upto 1200mm length for false ceiling all as specified |
| 60 | Providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screw as per manufacturers instructions |
| 61 | Taking up or down steel tubing and connectors 20 to32mm bore in new or old position (wall, ceiling, floor etc.) |
| 62 | Supplying and laying of 32 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified. |
| 63 | Supplying and laying of 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified. |
| 64 | Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified. |
| 65 | Supply and fixing PP-R Gate valves (brass insert) as per requirement of the site for Outer dia of pipes 20 mm all as specified and directed. |
| 66 | Supply and fixing PP-R Gate valves (brass insert) as per requirement of the site for Outer dia of pipes 25 mm all as specified and directed. |
| 67 | Supply and fixing PP-R Gate valves (brass insert) as per requirement of the site for Outer dia of pipes 32 mm all as specified and directed. |
| 68 | Supply and fixing Male Brass Threaded Adaptor (MTA/ MBTA) for CPVC pipe outer diameter 20 mm all as specified and directed. |
| 69 | Supply and fixing Male Brass Threaded Adaptor (MTA/ MBTA) for CPVC Pipe outer diameter 25 mm all as specified and directed. |
| 70 | Supply and fixing Male Brass Threaded Adaptor (MTA/ MBTA) for CPVC pipe outer diameter 32 mm all as specified and directed. |
| 71 | Supply and fixing Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC pipe outer diamenter 20 mm all as specified and directed. |
| 72 | Supply and fixing Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC pipe outer diameter 25 mm all as specified and directed. |
| 73 | Supply and fixing Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC pipe outer diameter 32 mm all as specified and directed. |
| 74 | Supply and fixing Tank Adaptor for CPVC pipe outer diameter 32 mm all as specified and directed. |
| 75 | Supply and fixing Tank Adaptor for CPVC pipe outer diameter 25 mm all as specified and directed. |
| 76 | Removal of air lock in internal water supply system of pipe of any dia all as directed. |
| 77 | Cleaning of water tank exc 250 & n.exc 500 lit, including cleaning all scales and dirts from inside of tank using bleaching powder and washed with water, complete all as specified including taking down and re-fixing of float valve. Including mentioning date of cleaning on water tank using white synthetic enamel paint as existing complete all as specified and as directed. Note :- After Cleaning of water tank, The rep of contractor shall be checked during water supply time and ensure water is reaching to the qtr and float valve is working properly and no leakage at joints. |
| 78 | Cleaning of water tank exc 500 & n. exc 1000 lit, including cleaning all scales and dirts from inside of tank using bleaching powder and washed with water, complete all as specified including taking down and re-fixing of float valve. Including mentioning date of cleaning on water tank using white synthetic enamel paint as existing complete all as specified and as directed. |
| 79 | Cleaning of water tank exc 1000& n. exc 2000 lit, including cleaning all scales and dirts from inside of tank using bleaching powder and washed with water, complete all as specified including taking down and re-fixing of float valve. Including mentioning date of cleaning on water tank using white synthetic enamel paint as existing complete all as specified and as directed. |
| 80 | Supply and fixing in repairs PVC Lid/ cover for 500 lit to 1000 lit Capacity water tank , complete all as specified and as directed. |
| 81 | Supply and fixing in repair three layer anti microbial rotational moulded PVC water storage tanks 250 litre capacity (cylindrical vertical with threaded type cover and White colour) hoisted and fixed in position all as specified including taking down old broken/cracked water tank and reconnecting the water pipe line in position. |
| 82 | Supply and fixing in repair three layer anti microbial rotational moulded PVC water storage tanks 500 litre capacity (cylindrical vertical with threaded type cover and White colour) hoisted and fixed in position all as specified including taking down old broken/cracked water tank and reconnecting the water pipe line in position. |
| 83 | Supply and fixing in repair three layer anti microbial rotational moulded PVC water storage tanks 750 litre capacity (cylindrical vertical with threaded type cover and White colour) hoisted and fixed in position all as specified including taking down old broken/cracked water tank and reconnecting the water pipe line in position. |
| 84 | Supply and fixing in repair three layer anti microbial rotational moulded PVC water storage tanks 1000 litre capacity (cylindrical vertical with threaded type cover and White colour) hoisted and fixed in position all as specified including taking down old broken/cracked water tank and reconnecting the water pipe line in position. |
| 85 | Supply and fixing in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20 mm dia all as specified and directed. |
| 86 | Supply and fixing in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 25 mm dia all as specified and directed. |
| 87 | Taking down serviceable bib tap, angle cock, stop cock, heath faucet etc. and cleaning , servicing ,putting washer etc. and refixing on same pipe line all as specified and directed. |
| 88 | Supply and fixing in repair plastic water closet seat cover white colour closed pattern with flat bottom and cover and MSCP with hinging device for Rimless cascade type water closet complete all as specified and as directed. |
| 89 | Supply and fixing in repair 100mm Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete Type B-1 (1:2:4) all as specified and directed. |
| 90 | Supply and fixing in repairs PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed |
| 91 | Supply and fixing in repair vitreous china, wash down water closet (EWC) white colour with PVC seat cover, closed pattern with flat bottom and cover with mild steel (CP) or aluminium hinging device fixed with necessary bolts complete all as specified. |
| 92 | Supply and fixing in repair vitreous China wash basin, white coloured, flat back 550x400mm including waste coupling CP, fixing brackets, cutting for and pinning in ends of brackets all as specified. |
| 93 | Supply and fixing in repair PVC valve less symphonic action type flushing cistern low level with inlet ball valve float and handle including brackets 10 litres capacity all as specified and directed. |
| 94 | Supply and fixing in repair 15mm bore chromium plated bib taps (fancy type), long body cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed for iron pipes all as specified and directed. |
| 95 | Supply and fixing in repair 15mm dia bore pillar taps, cast copper alloy, fancy type capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and directed. |
| 96 | Supply and fixing in repair 15mm bore stop valves chromium plated cast copper alloy, fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes (concealed type) all as specified and directed |
| 97 | Supply and fixing in repair Chromium plated health faucets (hand held shower type) with shut off valve (thumb or push button type) to allow controlled and continuous flow of water with adequate length and wall mounted pedestal for hanging the faucet etc. complete all as specified and as directed. |
| 98 | Supply and fix in repairs 15 mm dia Angular stop valve, Brass chromium plated complete all as specified and as directed. |
| 99 | Supply and fixing in repair waste coupling, brass, chromium plated with long shank, half thread, 32mm dia, for WHB/urinal etc. complete all as specified and directed. |
| 100 | Supply only waste pipe of polyethylene of low or high density or PVC ,32 mmdia for urinal/wash basin/ flush tank fixed in repairs. complete all as directed. |
| 101 | Supply and fixing in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed all as specified and directed. |
| 102 | Supply and fixing in repair cast copper alloy, brass chromium plated towel rail, 600mm long complete all as specified and directed. |
| 103 | Supply and fixing PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed. |
| 104 | Supply and fixing for Bathroom plastic cabinet of size 0.45 x 0.55 x 0.12 mtr with mirror complete all as specified and as directed |
| 105 | Supply and fixing in repairs multi-purpose corner shelf of size 300x 300mm, clear colour with stainless steel wall brackets and two grill bars, approved quality complete all as specified and as directed |
| 106 | Supply and fixing in repair Rimless cascade type water closet complete all as specified. |
| 107 | Supply and fixing in repair Counter top Wash hand basin complete all as specified. |
| 108 | Supply and fixing in repair single lever tall body wash basin basin mixer tap complete all as specified. |
| 109 | Supply and fixing in repair wall mixer complete all as specified. |
| 110 | Supply and fixing in repair aquamax concealed & external body complete of single lever shower mixer with 3 way diverter all as specified. |
| 111 | Supply and fixing in repair Bib cock all as specified. |
| 112 | Supply and fixing in repair Hand shower all as specified. |
| 113 | Supply and fixing in repair shower arm 60cm all as specified. |
| 114 | Supply and fixing in repair SS overhead shower square 240x240mm all as specified. |
| 115 | Supply and fixing in repairs towel rack all as specified. |
| 116 | Supply and fixing in repairs towel rail all as specified. |
| 117 | Supply and fixing in repairs towel ring all as specified. |
| 118 | Supply and fixing in repairs toilet paper holder all as specified. |
| 119 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified. |
| 120 | Material & Labour Glazed ceramic coloured tiles in patches 300x200x7mm thick in vertical surfaces of stone/brick wall, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick backing coat plaster in CM 1:4 all as specified. |
| 121 | Material & Labour Glazed ceramic coloured tiles 350x250x7mm /450x350x7mm thick in vertical surfaces of stone/brick wall, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick backing coat plaster in CM 1:4 all as specified. |
| 122 | Material & Labour for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11Sqm and nexc .18 Sqm in floor etc. set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles and including 15 mm thick screed bed in CM 1:4 all as specified. Complete all as specified and directed. |
| 123 | Material & Labour for vitrified tiles 9mm thick (light shade ) (square/rectangular) polished, area of each tiles exc 0.36 sqm & n exc 0.42 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and including 15 mm thick screed bed plaster in CM 1:4 all as specified. Complete all as specified and directed. |
| 124 | Material & Labour for vitrified tiles 9 mm thick (light shade ) (square/rectangular) polished, area of each tiles exc 0.42 sqm & n exc1.00 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and including 15 mm thick screed bed plaster in CM 1:4 all as specified. Complete all as specified and directed. |
| 125 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar. |
| 126 | Material & Labour machine cut granite stone slab 20mm thick of approved colour and shade as in floors, kitchen platform, steps and other similar situations over and including 15mm thick backing coat in CM 1:4 laid and jointed in grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the slab including grinding and polishing all as specified. |
| 127 | Rounding to edges of stone slabs to one edge, such as in kitchen platform, steps and other similar situations |
| 128 | Demolition of laterite block masonry / brickwork/ Pre-cast cement concrete block masonry, built in cement mortar complete all as specified and directed |
| 129 | Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water,etc.complete all as specified and directed. |
| 130 | Material & Labour for Pre-cast cement concrete block masonry 1:3:6 type C1 (using 20 mm aggregate)with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified. |
| 131 | Material & Labour rendering 15mm thick on any faces of brick work or concrete surfaces in CM 1:6 finished even & smooth without using extra cement complete al as specified and directed. |
| 132 | Material & Labour rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement complete al as specified and directed. |
| 133 | Material & Labour rendering 05 mm thick on fair faces of ceiling surfaces in CM 1:3 finished even & smooth without using extra cement complete al as specified and directed. |
| 134 | Material & Labour for preparation of new plastered surfaces of ceiling and applying two or more coat of coat of interior oil emulsion paint as per manufacturers instructions including a coat of alkali resistance priming paint |
| 135 | Material & Labour for preparation of new surface of wall and finishing walls with two coat of Premium Acrylic Smooth exterior emulsion paint with Silicone additives required shade ,two or more coats applied @ 1.43 ltr/10sqmand including priming coa\t of exterior primer applied @ 2.2 Kg/10 sqm as per menufacturers instruction and all as specified and directed. |
| 136 | Material & Labour for preparation of new plastered surfaces on wall and applying two or more coat of coat of interior oil emulsion paint as per manufacturers instructions including a coat of alkali resistance priming paint Please Enable Macros to View BoQ information |
