|
| 1 | Taking down tarfelt incl cement mortar bedding from roof surfaces and lowering and removing the same to a distance exc. 50m and n. exc. 100m incl roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed . |
| 2 | M & L screed bed or bedding layer 15 mm thick screed bed or bedding layer in CM (1:4) mixed with WPC as per manufacturer instruction for laying of APP membrane complete all as directed by the Engr-in-Charge. |
| 3 | Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed |
| 4 | M& L for bituminous primer @ 0.50 KG/Sqm over the cement plaster incl preparation of surfaces as per manufacturers instruction complete all as specified and as directed by the Engr-in-Charge. |
| 5 | M & L APP based polymeric membrane minimum weighing 3kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/Sqm) land on primed surface by forced application complete all as specified and as directed by Engr in Charge. |
| 6 | M & L for finishing the Bituminous surface with aluminium paint @0.15 Ltr/Sqm as per manufactures specifications and under strict supervision of manufactuer's technical representative complete in all respects as directed by Engr-in-Charge |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed. |
| 8 | M&L for Virified Ceramic tiles Double charged 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified and directed. |
| 9 | M&L for Virified Ceramic tiles Double charged 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile 10mm thick rendering on fair faces of brick work or concrete surface in CM 1:4 for laying wall tiles. complete all as specified and directed |
| 10 | M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified and directed. |
| 11 | M&L for 10mm thick rendering in CM (1:4) as in vertical surfaces of wall as in skirting/dado etc complete all as specified and directed. |
| 12 | M & L for glazed ceramic colour tiles 350X 450 X 7 mm thick as on cup board vertical surface of wall such as skirting, dado, riser etc. in Bath, WC and Kitchen set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 13 | Dismantling water tanks and removing from site of capacity 500 ltrs. |
| 14 | S & F 1000 ltrs rotational moulded polyethelene water storage tanks (cyclindrical vertical with closed top) incl necessary fittings for connection with pipes securing access covers etc as specified and as directed. |
| 15 | S&F in repair 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut. |
| 16 | Taking up or down GI 15mm bore pipe and connection including cleaning for refixing or removal from site as directed. |
| 17 | Taking up or down GI 20mm steel tubing and connections incl cleaning for refixing or removal to store. |
| 18 | Cutting chases, pinning in, making good to facings where required andpointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealedwater tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth |
| 19 | S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed. |
| 20 | S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed. |
| 21 | Demolition of brick masonary work, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding precast concrete articles etc. complete all as specified and directed. |
| 22 | M&L for brickwork with old size fly ash sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 23 | Taking down cement plaster on wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed. |
| 24 | M&L for 20 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item of schedule 'A'). |
| 25 | M & L for preparing new Plastered surfaces of wall and applying 2 mm thick wall care putty and there after two coats of exterior emulsion paint or tinted over a coat of primer complete all as specified |
| 26 | M&L 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished fair and even (without using extra cement) complete all as specified and directed. |
| 27 | M&L for prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying a coats of cement based wall putty 2 mm to wall surface complete all as specified and directed. |
| 28 | M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coat of cement based wall care putty 1 mm each including complete removal of existing treatment all as specified and directed. |
| 29 | M & L for complete removal of existing treatment and finishing the walls with Acrylic smooth exterior paint of required shade over a coat of primer after applying a coats of cement based wall putty 2 mm to wall surface complete all as specified and directed. |
| 30 | M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement. |
| 31 | M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and directed. |
| 32 | M&L for preparartion of old surfaces applying two coat of white washing on ceiling surface complete all as specified and directed. |
| 33 | Demolition of reinforced cement concrete Roofs, floors (other than groundfloors), beams, staircases, landing, chajjas and similar suspended work complete all as specified |
| 34 | M&L RCC Type B1 M-20 (1:1.5:3) (20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified. |
| 35 | M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 36 | S&F in repair Vitreous China wash basin Pedestal pattern, white, flat back size 580x450 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipeincluding brackets, complete all as specified and as directed by Engr-in-Charge. |
| 37 | S&F in repair 15 mm fancy type pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore. |
| 38 | S&F in repairs 600mm x 450 mm bevelled edge mirror of selected quality, mounted on 6 mm thick AC plain building board and fixed to wall on wooden plugs with chromium plated brass screws and cup washers all complete as specified and as directed. |
| 39 | S&F of in repair vitreous china squatting pan \\"Orissa\\" pattern size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S\\" trap from or back inlet etc including connection to trap and flushing pipe and provision of lime concrete bedding complete all as specified and as directed |
| 40 | S&F in repair 10 ltr capacity dual type PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified and directed. |
| 41 | S&F in repair 15 mm bore angle cock CP with flage complete all as specified and direcrted |
| 42 | S & F in repair 15mm bore PVC Connection with PTMT nut of length 600 mm complete all as specified and directed |
| 43 | S& F in repair for 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 44 | Taking down CI/PVC/AC soil pipe with fittings from wall, treches of any description including fittings. |
| 45 | S & F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 46 | S&F 110mm dia PVC bends of any radius with acess door. |
| 47 | S&F 110mm dia PVC SWR vent cowl |
| 48 | S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints |
| 49 | S&F 75 mm bore PVC (SWR) bends of any radius. |
| 50 | Taking down chowkat with shutter n exc 1.5 sqm each and removing from site. |
| 51 | S&F Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed incl fixing of hold fast as per specification and drawing complete all as Specified. |
| 52 | S&F Factory Made Solid PVC panel Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 4mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Wood free EPS complete all as Specified. |
| 53 | S&F 150 mm long Aluminium anodised barrel tower bolts complete all as specified and directed. |
| 54 | S&F aluminium handles 150mm size cast type anodised complete all as Specified. |
| 55 | S&Fin repair 25mm dia curtain rod, chromium plated with fixing brackets etc. complete as specified and as directed. |
| 56 | Supply and fixing powder coated aluminium sliding window sliding on 3 tire frame of section 92mm X30mmX1.55 mm and shutters of section 20 mm X 40 mmX 1.55 mm fixed with 4 mm thick plain glass with rubber gasket, handles lock, 'U' channel with provision for aluminium grill fixed with aluminium frame etc all as specified and directed by the Engr-in-Charge. |
| 57 | Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each and removing from site. |
| 58 | M& for fabrication and fixing of anodised aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 101.6mm x 44.45mm x 2mm and section of bottom and top rail of section114mmx44.45mmx2mm thick and and lock rail shutter frame of 83mm x 44.45mm x 2 mm with and including panels of 5.5 mm thick plain/frosted float glass,and with anodised aluminium snap beading of size 18.2mmx16.66mm scred for fixing fully including double action door spring hydraulically regulated made up of 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and all necessary fittinngsand EPDM rubber packing each shutter shall be provided with two decorative type aluminium disc handle of 150 mm dia per shutter ,1 no heavy duty door shutter 1no 200mm long aluminium tower bolt per shutter including complete all as specified and as directed by the Engr-in-Charge. |
| 59 | Supply and powder coated (minimum 50 micron) anodised aluminium frame for doors, windows, ventilators, partitions with one or more rebates with stainless steel screws /including PVC protector sheeting and joining cleat for fixing etc. including taking down old one complete all as specified and as directed by Engr-in-Charge. |
| 60 | Dismantling wrought iron or mild steel work of any description as in door, gates etc and similar works complete all as directed by the Engr-in-Charge. |
| 61 | S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 62 | S&F steel work in Trusses, purlins, posts and the like using tubular/ square hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming I.S.1161-2014/IS 4923-1977 grade St-240 complete all as specified and as directed by the Engr-in-Charge. |
| 63 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed by the Engr-in-Charge. |
| 64 | Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm |
| 65 | Excavation in trenches n.exc 1.5 in deep and n.exc 1.5 m wide for foundation etc not exc 10 sqm on plan and getting out in soft / loose soil |
| 66 | Demolition of precast block masonary / Brick work or precast concrete article built in cement mortar |
| 67 | Demolition of reinforced cement concrete of any description and in any position such as precast manhole cover or cover slabs of septic tank etc (reinforcement cut as required to facilitate demolition) |
| 68 | M&L for precast RCC 1: 2 :4 type B-1 using 20mm graded aggregate set in cement mortar 1:4 as in manhole covers including necessary formwork complete all as specified and as directed |
| 69 | S&F for PVC (SWR) (Bore of pipe 150mm) pipes with working pressure 6 kg/cm2 single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as directed by Engr-in-Charge. |
| 70 | S&F for PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as directed by Engr-in-Charge (Bore of bend 150mm) |
| 71 | M&L for mild steel TMT bars 6mm to 8mm dia cut to length , bent to shape required, including cranking , bending and binding with MS wire , not less than 0.9 mm dia or securing with clip. |
| 72 | M&L PCC 1:3:6 type C-2 (40mm graded aggregate) as in foundations, filling and mass concrete |
| 73 | M&L for 15 mm thick plastering in cement mortar 1:3 on brick or concrete surface finished even & smooth without using extra cement |
| 74 | M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 150mm |
| 75 | Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/ loose soil complete all as specified. |
| 76 | Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified. |
| 77 | M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required dia of pipe 150mm |
| 78 | M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4. |
| 79 | M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed |
| 80 | M&L PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) for making of chamber base all as specified and as directed |
| 81 | Material and labour for brick work with sub-class ‘B’ bricks, set in cement morter (1:4) straght or curved on plan, exceeding 6m mean redious as in manholes and septic tanks complete all as specified and directed. |
| 82 | M&L for rendering 15mm thick in CM 1:3 as in fair faces of brick work or concrete surface of wall and finished surface even and fair without using extra cement with using wpc as per manufacturer instruction (measure seperately)complete all as specified and directed. |
| 83 | Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded aggregate) as in coping of manholes channels etc complete all as specified and directed |
| 84 | M & L for precast RCC (1:2:4) type B1 using 20mm graded stone aggregate as in cover slabs of drains set in CM (1:6) including necessary form work complete all as specified and as directed by the Engr in Charge. |
| 85 | Supply and fixing for mild steel TMT bars, 10 mm dia, cut to length, bent to shape as required including cranking, bending and binding with mild steel wire (annealed)not less than 0.90 mm dia complete all as specified and directed. |
| 86 | M&L for DWC HDPE ( Double wall corrugated High density poloyethene ) pipe for 150mm bore pipe BSL-16098 ( Part-II) 2013 laid and jointed complete with collers, laid and jointed on concrete bed complete in cluding testing complete all as specified and directed |
| 87 | M&L for providing PCC 1:2:4 type B-1( using 20mm graded stone aggregate) as in cast in situ lintels upto 1.5 M span, cills and other similar bands, plinth courses, parapets, copings,benching to manholes, bed plates and the like weathering and slightly rounded or angles and throating as directed including formwork complete all as specified and directed. |
| 88 | Cutting into existing bituminous road/PCC footpath and making good the disturbed surface with PCC 1:2:4 type B2 any length and size complete all as specified and as directed |
| 89 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed. |
| 90 | M&L Point wiring for Point controlled by one moduler switch with 1.5 sqmm PVC insulated FRLSH unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 20 mm dia non metallic rigid PVC conduit ( ISI marked ) concealed in wall with 1.5 mm thick pressed steel terminal boxes ( modular type ) concealed in walls painted the same inside and out side with one coat of black bitumen paint incl inner and outer moduler plate for fixing of modular switches/ regulator etc along with PVC insulated and insheathed FRLSH 1.5sqmm multi stranded copper conductor cable (green color) as earth lead as directed by Engr- in- charge. |
| 91 | (a) One light point controlled by one way switch 5/6 amps. |
| 92 | (b) One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps. |
| 93 | (c) One socket out let 5/6 amps point on the same board |
| 94 | (d) One socket out let 5/6 amps point on the independent board |
| 95 | All as per item No 2 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed. |
| 96 | S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed. |
| 97 | S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed. |
| 98 | S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed. |
| 99 | S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed. |
| 100 | S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 101 | S&F LED lights fitting 1x 20W, 220V AC decorative box type with driver,IP 20, class I, wall/ surface mounted, integrated type with extruded aluminium housing integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all accessories internally prewired and including necessary taking down the old unserviceable fitting complete all as specified. |
| 102 | S&F LED Bulk Head lights fitting 1x 9/10W, 220V AC integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed etc connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified. |
| 103 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp,IP 20, class I, wall/ surface mounted, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 104 | S&F in repair Decorative luminiare suitable for wall light fixture including LED lamp 1x19 watt ( B-22 base) ,made of unbrakeable Polycarbonate with Acrylic decorative diffuser, IP-65 protection, and provision of PVC insulated sheathed round flexible wire with multi stranded copper conductor of size 1.5 Sq mm two core complete all as specified and directed Make : Havells, cat part No.LHDL06160099 or equivalent of Philips/Bajaj. |
| 105 | Supply and fixing Ceiling Fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified by Engr in charge. |
| 106 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified |
| 107 | S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB\\"S/lsolators complete including taking down the old one complete all as specified and directed by Engr-in-Charge. |
| 108 | Supply and Fixing in repair MCB DB double door, powder coated sheet metal enclosure, 4 way 240 volts grade Triple pole and neutral with 200 amps rated bus bar,IP 43 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete including taking down the old one complete all as specified and directed by Engr-in-Charge. |
| 109 | S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified and directed by Engr-in-Charge. |
| 110 | S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘B’ curve, 10 KA all complete including taking down the old one complete all as specified and directed by Engr-in-Charge. |
| 111 | M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified and directed by Engr-in-Charge. |
| 112 | M & L Sub main wiring concealed type with two run single core cable PVC insulated cable with 6.0 Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 6.0 Sqmm connected to common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size, making good the disturbed surfaces complete including taking down old submain wiring.(NOTE : Two run of submain wiring cable alongwith one run of earth wire shall be measured as one length.) . |
| 113 | Taking down ceiling fan/exhaust fan sealing cable end, dismantling blades and removing fan and blades to store complete all as specified by Engr in charge Please Enable Macros to View BoQ information |
