|
| 1 | Supply & fixing steel tubular pole 9 Metre long designated 410 SP-29 in 1:3:6 cement concrete foundation including excavation back filling etc. complete in all respect. |
| 2 | Supply, sagging, jointing and binding of insulated ACSR Weasel conductor including cost of aluminium tape binding and jointing sleaves etc. complete in all respect rate as per sanctioned . |
| 3 | Supply & Fixing of 32 MM Dia 1.20 Mtr long G.I Pipe Bracket For Fixing of LED lights complete in all respects with clamp etc |
| 4 | Supply & fixing of 100 x 110 mm shackle insulator / 100x80 mm pin insulator including G.I. Bolts / spindle nuts etc.Complete in all respect. |
| 5 | Painting of the electric pole with 2 coats of aluminium paint over red oxide primer complete in all respect |
| 6 | Supply & fixing of M.S Earthing Rod (2500x20mm) in vertically ground level and connecting the pole with the help of 6 SWG GI wire including cost of all material men & TNP |
| 7 | Supply and Wiring of submains with two Nos of 2.5 sq. mm.FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material labour and T&P required for proper completion of the work as directed at site by Engineer in charge as per uppwd no 289 Make Havells/Polycab/KEI/Gloster/Grandley |
| 8 | Supply and laying of aluminium conductor 10 sqmm 2 core PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a HDPE/DWC Pipe below the ground level as per UPPWD Sch No 501(b) Make Havells/Polycab/KEI/Gloster/Grandley |
| 9 | Supply and laying of aluminium conductor 16 sqmm 2 core PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a HDPE/DWC Pipe below the ground level as per UPPWD Sch No 501(c) Make Havells/Polycab/KEI/Gloster/Grandley |
| 10 | Supply and laying of aluminium conductor 16 sqmm 4 core PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a HDPE/DWC Pipe below the ground level as per UPPWD Sch No 501(i) Make Havells/Polycab/KEI/Gloster/Grandley |
| 11 | Supply & laying of 63mm dia (OD-63mm & ID-51mm nominal) DWC HDPE pipe ISI marked along with all accessories like socket, bend, couple etc. confirming to IS 14930 Part II complete with fitting and cutting jointing etc direct in ground ( 75 cm below ground below) including excation and refillling the trench but excluding sand cushoning and protective covering etc. complete |
| 12 | S/F of following capacity of automatic street light cubical cantrol panel painted with anti corrosive alkali and acid proof paint consisting of timer switch TSO 100 series with cintractors HRC fuses, isolating switch metering instuments box with CTS etc. as per UPPWD Sch. No. 807(e-ii) (25 Amp. TPN) |
| 13 | Supply & fixing 40A TPN automatic street light panel cubical panel painted with anti corrosive alkali acid proof paint consisting of time switch TSO 100 series with contractors, HRC Fuses, isolating switch metering instrument & instrument box with CTs etc |
| 14 | Supply and fixing of LED Street light fitting having die cast aluminium body and diffuser with driver set suitable for 110-130W watt confirming to IP 66 protection complete in all respects (With 5 Year Gaurantee(3+2) Three year all type (including Damage & Theft) Repair & Maintenance & Extra Two Year Gaurantee).CAT AAA(Bajaj, Philips, Crompton, Wipro make) UPPWD 1424 |
| 15 | Supply & fixing of 0.5 Amp to 6.0 Amp SP MCB in M.S Box complete in all respect (Cat B ) as per UPPWD Sch item no 1001 |
| 16 | Supply & laying 25 sq mm 3.5 core Al. conductor PVC insulated armoured, served, sheated cable 1100 V garade in existing HDPE pipe laid below ground level. The armouring of the cable shall be properly connected with earth conductor by clamp etc. as per PWD Sch. 501(j) & 507 (Polycab /KEI/ Havells/ Grandley/Gloster Make) |
| 17 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respect as per direction of the Engineer- incharge as per UPPWD sch. No. 504 (c) 25 sq. mm |
| 18 | S/F of brass nickel Plated compression gland for PVC insulated and armoured served sheated ,underground cable including rubber ring etc. comlete in all respects.the armouring of the cable shall be properly connected with the earth as per direction of Engineer-incharge as per UPPWD sch. no. 503 (j) 25 sq. mm 3.5 core |
| 19 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respect as per direction of the Engineer- incharge as per UPPWD sch. No. 504 (c) 10 sq. mm |
| 20 | S/F of brass nickel Plated compression gland for PVC insulated and armoured served sheated ,underground cable including rubber ring etc. comlete in all respects.the armouring of the cable shall be properly connected with the earth as per direction of Engineer-incharge as per UPPWD sch. no. 503 (b) 10 sq. mm 2 core |
| 21 | S/F of 40mm dia x 4.5 mtr long GI pipe vertically for earthing having 12 mm earthing 12mm di holes spaced 75mm apart drilled upto 2 mtr from the bottom complete with earthing lead no 6 to 8 SWG wire GI wire in GI pipe upto appron upto switch board 30 CM square box with hinged cover masonary enclosure funnel of top , alternate layers of charcoal and at least 150 mm thick alround as per UPPWD Sch no 701 |
| 22 | supply & laying of 25 mm x 3mm G.I Strip from earth electrode directly in ground as required aspects as per uppwd Scho no 716 |
| 23 | Strengthening of ST/Octogonal pole/High Mast/Panel, foundation by providing new concreting including broken of weak foundation,excavation below upto Ground level,Surface finishing and painting with white cement and dark yellow colour cost of all material men and T&P complete in all respect . |
| 24 | Painting letters (Pole no.) 2.5 cm upto 8.0 cm size complete on street light pole/panel/other electrical properties under UPSIDA including cost of all material men and T&P complete in all respect rates as per sanctioned . |
| 25 | Painting of ST pole high mast foundation excavation below upto ground level surface finishing and painting with white cement and dark yellow colour paint with double coat including cost pf all material men and T&P complete in all respect . |
| 26 | Supply & Fixing of Decorative Pole made of mild Steel with a total height of 7 mtr above ground level with Single arm bracket for S.L and predefined laser cut pattern in the top portion of the bracket of the pole. Pole bottom base section shall be 250x250x1500mm, 4mm thickness column with two side predesigned laser cut to illuminate the surrounding in 20W with noticeable mode, between section pole of 90x4500x3.2mm, then 76x1000x3mm top bracket with illuminated laser cut pattern design one side of 1000mm to bold the S.L. as per shared drawing. The base plate of pole shall be of size 400x400x12mm. Provision for inside termination box with for away connector & Ions 6 Amps MCB for local isolation. The pole is primarily coated with primer, secondary epoxy resin and top coated with UV stabilized powder coat and cured. The decorative pole is suitable for outdoor lighting application. Pole light is complete in all aspects with all accessories with foundation bolts. |
| 27 | Supply & fixing of 16mtr high mast shaft of approved make with rising system hot dip galvanized inside & outside dip, heavy pole sheet thickness 3mm top dia minimum 150 mm bottom dia minimum 360mm base plate thickness 32mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferntial weld with accesories for high mast such as head suitable for 6 to 12 lumaniries and its control gear boxes 1.5HP power tool 3 point suspension system with steel wire rope 6mm dia double drum winch including making suitable foundation as per manufacture drawing/ site requirement along with foundation bolts nuts washer anchor plate etc complete in all respect as per UPPWD Sch no 652( Bajaj/Phillips/Crompton/Wipro make) |
| 28 | Supply and fixing of factory wired integral LED Flood light lumanaries with die cast aluminium body and diffuser with driver set suitable for 200 watt confirming to IP 66 protection complete in all respects (With 5 Year Gaurantee(3+2) Three year all type (including Damage & Theft) Repair & Maintenance & Extra Two Year Gaurantee). Catt. AAAas per UPPWD Sch. No.1455( Bajaj/Phillips/Crompton/Wipro make) |
| 29 | Supply & errection of double pole structure with hardware & fittings on 410 SP-56 11 mtr long complete with 1/6th of over all length of pole in cement concrete with one feet square/ one feet dia cement concrete plinth around the pole above ground level. the foundation of underground will be of cement concrete in the ratio of 1:2:4. the stone ballast/ brick- ballast used will be 1.25cm (1/2 x 1) size with the stone pad 30x30x7.5cm at the base including all T&P men & material for proper completion of work as per direction of engineer in charge. |
| 30 | Supply & fixing of 11KV pin insulator on channel arm fixed on ST/DP including cost of nut/bolt/washer T &P men & material for proper completion of work as per direction of engineer in charge |
| 31 | supply & errection of stay set HT line for ST pole with GI anchor plate( 152x152x6mm) stay rod(16mm dia x 1.85 mtr long) GI stay below (16mm dia, thriple , double stay , tightner, stay insulator, clamps & stay wire including grouting in 1:4:8 ratio of cement concrete using course sand, over brunt brick ballast including all T & P men & material for proper completion of work |
| 32 | supply and fixing of MS top channel 125x65x2240 mm including cost of holding clamps ans materials for proper completion of work as per direction in charge |
| 33 | supply and fixing of MS top channel 100x50x2000 mm including cost of holding clamps ans materials for proper completion of work as per direction in charge |
| 34 | supply & fixing of 11kv TPMO with complete with insulator & other accessories (Relco/azad/rama other standard make approved by UPPCL) proper completion of work as per direction in charge |
| 35 | supply and fixing of of bolt channel/misc channel/other item as per site requirement including all T&P men & material for proper completion of work as per direction in charge |
| 36 | supply & fixing of clamp suitable securing the above channel completes as per SIDC Sch no 3(4) |
| 37 | S/F of 11KV three phase D.O fuse set complete with suitable clamps nuts & bolt fuse wire etc . As per rate of uppcl 2021-22 sr no 99 |
| 38 | supply and installation, testing & commisioning of outdoor type aluminium wound oil cooled transformer rating 63 KVA 11/0.4 KV on double pole including cost of base channel & holding clamps approved by uppcl proper completion of work as direction of engineer in charge |
| 39 | supply & laying of 70 sq mm 3 core Al conductor XLPE insulated PVC bedded galvanised flat steel strip armoured, served sheated cable 1100v grade in existing HDPE pipe laid below ground level . The armouring of the cable shall be properly connected with earth conductor by clamp as per PWD sch no 506(d) & 507 (Polycab/KEI/Havells/Grandley/Gloster make) |
| 40 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respect as per direction of the Engineer- incharge as per UPPWD sch. No. 504 (e) 95 sq. mm |
| 41 | Supply & laying of 90mm dia DWC HDPE pipe ISI marked along with all accessories like socket, bend, couple etc. confirming to IS 14930 Part II complete with fitting and cutting jointing etc direct in ground ( 75 cm below ground below) including excation and refillling the trench but excluding sand cushoning and protective covering etc. complete. |
| 42 | S/F of outdoor/indoor type 11KV jointing kit heat shrinkable type for 11kv cable including cost of all material, labour T&P etc proper completion of work |
| 43 | Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only uppwd no 801(b) (Incomming 100 Amp,32 AMP TPN 03) |
| 44 | Supply & erection of stay set at 3.5 Metres away from the pole complete with galvanised 19 mm dia x1.80 Metre long stay rod, 30 cm x 30 x 6.3 mm anchor plate, thimble stay clamps, stay insulator,19 mm 600 mm double screw tightener, 7/3.5 mm G.I. stay wire etc. in 1:3:6 cement concrete complete in all respect. UPPWD 631 Please Enable Macros to View BoQ information |
