|
| 1 | S&F in repairs for Vitreous China table top wash basin, white or ivory colour flat back, size 530mmx420mmx140mm/600x390x150mm/600x380x130mm excluding taps, waste chain and plug and porcelain stopper but including Coupling as per Model complete all as specified and directed. Make:Jaquar (cat part No. JDS-WHM-25907N),Parryware(Cat part No. WPC898Z46),Cera(cat part No.S2020172) |
| 2 | M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings self and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed. |
| 3 | M&L for mild steel TMT bars 10mm dia & over, cut to length, bent to shape reqd including cranking, bending specially for columns, hooking ends & binding with MS wire annealed not less than 0.9 mm dia welding as required at site complete all as specified and as directed. |
| 4 | M&L for reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate ) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed. |
| 5 | S&F in repairs Vitreous China Urinal,size of 375 x 400 x 615 mm Half stall type, white including SS concealed flushing cistern, flush pipe and including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing urinal spreader of PTMT any colour, grating and Union for discharge pipe fixed complete all as specified and directed. Make : Jaquar/ Parryware/ Hindware. |
| 6 | S&F 10mm thick toughnend frosted glass use as modular glass urinal partitions in chamfer shaps or as per required shape of each partitions including all fixing arrangement ie.stainless steel clamp/stud for hanging glass area exc 0.75 Sqm n exc 1.00 sqm complete all as specified and directed. |
| 7 | M&L Granite18 to 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, vertical surface of wall also and like in 12mm thick Screed bed or bedding layer cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed. |
| 8 | M&L for edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed. |
| 9 | S&F in repair of Vitreous china one piece EWC standard size white/ivory colour , wall hanging / floor mounted with dual flushing cistern white including 'P' or 'S' trap , fixed as complete all as specified and directed. Make: Jaquar (Cat part No.CNS-WHT-853S300SPPSM), Cera (CAT part No. S1013228) Parryware (Cat part No.WPC890N46) |
| 10 | S&F in repairs for Chromium plated brass angle valve for 15mm bore pipe, fixed complete all as specified and directed. Make : Cera (Cat No. : F8040204), Parryware (Cat No : WPT9926A1), Hindware (Cart part : F570043CP) |
| 11 | S&F in repairs for Chromium plated bib cock with wall flange, Screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as specified and directed. Make :Hindware (cat No:F690004CP),Parry ware(cat No-WPT5004A1), Cera(cat No.F2014151) |
| 12 | S&F in repairs for Wash basin mixer, with extension body, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified and directed. Make :Jaquar (cat part No.ALI-BCH-85011B),Hindware{(cat part No;F410012RGD (code;43104)} |
| 13 | S&F in repairs urinal spreader of CP any coloured for fixing with 15mm dia pipe all as specified and directed. Make:Hindware/Jaquar/Parryware |
| 14 | S&F in repairs for 5.50mm thick mirror of selected quality glass with edge moulding, mounted on wall fixed with SS stud fixed complete all as specified and directed. |
| 15 | S&F in repairs for Tubular towel rail of brass chromium plated, 20mm dia, D type, 60 cm long between flanges, fixed complete all as specified and directed by Engineer in Charge. |
| 16 | S&F in repairs for PVC connection 15mm dia and 45 cm long with 2 Nos PTMT nuts, fixed complete all as specified and directed. |
| 17 | S&F in repairs for 300mm Stainless Steel Connection Pipe/Hose Pipe with 2 Nos SS nuts Heavy Duty, Chrome Finish fixed complete all as specified and directed. |
| 18 | S&F in repairs for Pop up coupling of CP (half or full threaded) 32 mm to 45 mm bore fixed complete all as specified and directed.Make : Hindware/ Jaquar/ Parryware. |
| 19 | S&F for Rotational moulded polyethylene white water storage tanks 1000 litres capacity three layered white in colour ( clylindrical vertical with threaded closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of existing water tank complete all as specified and directed. Make : Sintax, Poly plast, Supreme etc |
| 20 | S&F 15mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including Taking up or down existing pipe and necessary cutting chasing into wall etc all as specified and as directed. Make : Jindal/ TATA/ UNIK etc. |
| 21 | S&F in repairs for brass chromium plated 40mm bottle traps with wall flange for wash basins/urinal pot with inlet and outlet screwed for pipe or connections including necessary packing, union, cap and reducer and fixed complete all as specified and directed. Make : Cera/ Hindware/ Parryware. |
| 22 | Cutting holes in bricks or RCC walls exc half brick built in cement mortar including making good after inserting and setting spouts complete all as specified and directed. |
| 23 | S&F for GI pipe 50mm dia medium grade laid on floor/inserted in wall including all fittings and taking down old GI pipe complete all as specified and directed by Engr-in-Charge. |
| 24 | Cutting chases, pinning in brick wall, stone or block wall at any height making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and making good, cutting exc 5 cm n ecx 15 cm girth complete all as specified and directed. |
| 25 | S&F for 20mm bore Tubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including Taking up or down existing pipe and cutting chasing into wall etc complete all as specified and directed. |
| 26 | S&F in repair grating doom 100 mm dia with /without waste hole of CP complete all as specified and directed |
| 27 | S&F in repairs flexible health faucet with clamp all as necessary fitting etc complete all as specified and directedMake : Jaquar/Parry ware/Hindware |
| 28 | S&F in repair for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and directed. |
| 29 | S&F in repairs for CP Toilet paper holder including all fitting and fixture complete all as specified and directed. Make : Jaquar/ Parry ware/ Hindware. |
| 30 | Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing the debris outside the defence land complete all as specified and as directed. |
| 31 | M&L for PCC 1:4:8 type D-2 (40 mm graded crushed stone aggregate) in foundation and mass concrete complete all as specified and directed. |
| 32 | M & L for PCC 1:2:4 type B-1 (20mm graded crushed stone aggregate) as in floor etc complete all as specified & directed. |
| 33 | M & L for super gloss finished/carving (PGVT) tiles external/Internal in vertical surfaces 600mm x 1200mmx 9 to 10mm thick over & including 10mm thick rendering in CM 1:4 set and jointed in neat cement slurry or tile adhesive and pointed in white or coloured cement to match including dismantling existing tile and removing the debris outside the defence land complete all as specified and as directed. Make : Orient ceramic/ H&R Johnson/ Kajaria etc. |
| 34 | M & L for anti skid/matte finish coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm over & including 15mm thick Screed bed or bedding layer in CM 1:6 for laying floor finishes, set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling existing tile and removing the debris outside the defence land complete all as specified and as directed.Make : Orient ceramic/ H&R Johnson/ Kajaria etc. |
| 35 | M&L for Plaster of Paris (POP) false ceiling of approved design and pattern (approved by GE), including G.I. framework, cornice/moulding, finishing and painting, complete in all respects as per direction of Engineer-in-Charge.Work shall be done with detailed Specifications are as under:(a) Providing G.I. framework made out of galvanized iron sections (ceiling angle, intermediate channel, perimeter channel etc.) of 0.5 mm thick, suspended from RCC slab using dash fasteners, including proper alignment and leveling (spacing approx. 600 mm c/c for main,300mm C/C for cross section).(b) fixing of chicken mesh on GI Frame work with help of screw/rivet etc. (C) Applying POP (Plaster of Paris) of average thickness 15-18 mm, including forming grooves, panels, drops, curves as per design.(d) Providing chicken mesh at joints of RCC slab and POP surface to prevent cracks.(e) Making POP cornice/moulding of size 75 mm to 150 mm at ceiling, wall-ceiling junction.and finishing the surface smooth by sanding, filling joints, making it ready for painting.(f) Applying one coat of primer and two coats of plastic emulsion paint of approved brand and shade(ie. Asian,Berger,Nerolac etc).Including cost of all materials, labour, scaffolding, tools & plants, curing, wastage, and taking down existing POP false ceiling/GRG false ceiling, all incidental charges required to complete the work. |
| 36 | M & L for complete removal of exiting suface treatment and applying approved make exterior/interior texture paint finish on wall surfaces, including surface preparation such as cleaning, scraping, sanding, filling cracks with putty, applying primer coat, and then applying texture coating one or more of required pattern/design using suitable tools, complete in all respects as per manufacturer specifications and direction by Engineer-in-charge. |
| 37 | Providing and fixing approved quality decorative wallpaper 400 Micron (Premium / 3D / textured) of required design, shade, and texture on prepared wall surface, including reomval of existing treatment and surface preparation such as cleaning, rubbing with sandpaper, filling undulations with putty, applying primer if required, and pasting wallpaper using recommended adhesive. The work includes proper alignment of patterns, cutting, finishing at edges, corners, and junctions, complete in all respects as per manufacturer specifications by Engineer-in-charge instructions. |
| 38 | Supply and fixing of UPVC door openable type in any position with 6mm thick toughened glass with Etching design of approved make including frame and all necessary fittings and fixtures complete all as specified and as directed by Engr-in-Charge. Make : Finesta, ECOCELL, Adopen, Yashpoly etc. |
| 39 | S&F factory made (cabinet work) of 18 mm thick HDMR board with 1 mm thick decorative laminate (sunmica) on outer face and balancing laminate on inner face, including 2 mm PVC edge banding, including dismantling old existing board complete all as specified & directed . Make : Century ply/ Green panel/ActionTesa/ RAJSHRI/ ECOCELL Note :- Colour approved by GE |
| 40 | S&F for Stainless steel soft close hinges 75 mm long for cabine/wordrobe leaf complete all as specified and as directed. |
| 41 | S&F for stainless steel wardrobe lock of approved make (such as Godrej / Ebco / Hettich / Dorset or equivalent), made of SS 304 grade, suitable for wooden/WPC wardrobe shutters, complete with:Lock body with cylinder mechanism 2 or 3 keys (nickel plated) SS strike plate Necessary screws, fittings & accessories Fixing on shutter including cutting/slotting if required The lock shall be corrosion-resistant, smooth in operation, and of approved design and finish complete all as specified and directed. |
| 42 | M&L for 75 mm long premium cabinet handles made of Stainless Steel Grade 304 (SS 304), heavy-duty quality, minimum 1.2–1.5 mm thickness, of approved make and design (sleek / designer / tubular / profile type), with satin / brushed / matte / PVD finish, including:(a) Supplying handles complete with high-quality SS screws, washers, and concealed fittings.(b) Anti-rust and corrosion-resistant material suitable for kitchen and wardrobe use.(c) Fixing on shutters/drawers of cabinets, wardrobes, modular kitchens, etc.(c) Accurate drilling, alignment, firm fixing, and finishing without surface damage(d) All labour, tools & tackles, scaffolding (if required), and complete installation. |
| 43 | M&L in repair for 450 mm long premium decorative type door handles made of Stainless Steel Grade 304 (SS 302), heavy-duty quality, minimum 10 mm thickness, of approved make and design (sleek / designer / tubular / profile type), with satin / brushed / matte / PVD finish, including:(a) Supplying handles complete with high-quality SS screws, washers, and concealed fittings.(b) Anti-rust and corrosion-resistant material suitable for doors.(c) Fixing on shutters of door, wardrobes, etc.(d) Accurate drilling, alignment, firm fixing, and finishing without surface damage. Design and shape of handles approved by GE. |
| 44 | S&F exterior grade aluminium composite panel sheet wood finish/marble in dark colour or metalic finish/glossy in dark colour of 4 mm thick fixed in grid/ceiling/wall /chajja,facia,cill,jamb,soffit or any type of parabolic shape/frame work of steel fixed on wall ,celiing,facia,chajja etc . composite sections/ panels with stainless steel rivets to approved size including necessary aluminium Grid/ framing, drilling etc,of sizes,shape and spacing as per manufacturers instructions complete including filling up joints with silicon sealant etc. lengths of sheets as customized at site of work and of shades .incl necessary scaffolding up to15m height as required complete all as specified. (Colour approved by GE) |
| 45 | S&F for steel roof truss ( Framed), framing on wall, trussed, purlins, crane gantries, rails,post and fastings and heavey bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe- 410-W Gde E- 250 complete all as specified and directed by Engr-in-Charge.Note :- (i) The steel used shall be of primary producer only. (ii) Work shall be excuted upto 10 Meter of height. (iii) All necessary precautions and safety measures shall be taken while execution of work. |
| 46 | Supply & fixing 8 mm thick toughened (tempered) glass door, made from approved quality clear float glass of reputed make such as Saint-Gobain / AIS Glass / ModiGuard or equivalent, machine cut to size, toughened and edge polished, including decorative acid etching / sandblasted design as per approved patternand cut-outs for fittings (handle, lock, floor spring, patch fittings, etc.)All edges polished smooth for safety the door shall be fixed with SS 304 grade patch fittings / hardware (brush/matte finish) including:Top & bottom patch fittings.Floor spring (heavy-duty)Glass door handle (SS, minimum 450 mm length).Lock arrangement (if required)Necessary clamps, connectors, screws, and accessories.Complete installation including alignment, leveling, sealing with silicone, and making good the surrounding surfaces, all as per site requirement and direction of Engineer-in-Charge. |
| 47 | M & L for Grinding & polishing of old kota stone/ marble/ baroda green floor/skirting with machine to mirror finish in and including making good of wall finishes as per original specifications complete all as specified and directed. |
| 48 | Demolition of reinforced concrete such as roofs, floors, beams, staircase, landing, chajjas, facia and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 49 | Cleaning of terrace/loft water storage tank (inside surface area) up to 1000 litre capacity, at all heights, including removal of silt, sludge and rubbish from the tank, scrubbing of internal surfaces using coconut brushes, duster, etc., washing with fresh water and disinfecting with bleaching powder @ 0.5 gm per litre capacity of tank.The item includes marking the date of cleaning on the outer surface of tank body using stencil and paint, complete as per direction by Engineer-in-Charge.Old dates already marked shall be removed using paint remover or black paint before marking new date. If date is not marked or old date not removed, recovery shall be made @ Rs. 0.10 per litre.During cleaning, any damage caused to GI fittings, ball cock, etc., shall be repaired/replaced by the contractor at his own cost, and nothing extra shall be paid on this account.The item also includes disposal of all malba/debris outside the premises as directed. |
| 50 | Cleaning of terrace/loft water storage tank (inside surface area) exc 1000 ltr and n.exc 2000 litre capacity, at all heights, including removal of silt, sludge and rubbish from the tank, scrubbing of internal surfaces using coconut brushes, duster, etc., washing with fresh water and disinfecting with bleaching powder @ 0.5 gm per litre capacity of tank.The item includes marking the date of cleaning on the outer surface of tank body using stencil and paint, complete as per direction of Engineer-in-Charge.Old dates already marked shall be removed using paint remover or black paint before marking new date. If date is not marked or old date not removed, recovery shall be made @ Rs. 0.10 per litre.During cleaning, any damage caused to GI fittings, ball cock, etc., shall be repaired/replaced by the contractor at his own cost, and nothing extra shall be paid on this account.The item also includes disposal of all malba/debris outside the premises as directed. |
| 51 | S&F Solar control film 50 micron reflective type in any pattern /coloured printed with LOGO/sign/photo etc sticked to glass panes as per instructions of manufacturers complete all as specified and directed. |
| 52 | Taking down chowkhat or frame exc. 4.00 sqm but n.exc 10.00 sqm each without taking off shutter from the frame complete all as specified and directed. |
| 53 | Providing, supplying, installation, testing and commissioning of automatic sensor-operated sliding glass door (Size: 2.1mX2.40m) system, comprising 12 mm thick toughened etched glass panels, complete with all fittings, fixtures, automation system, electrical works, and accessories, as per specifications and as directed by Engineer-in-Charge.The item includes :A. Glass Work12 mm thick toughened safety glass conforming to relevant IS standards,Acid etched / sandblasted design as per approved pattern by GE, Machine polished edges with rounded corners.B. Door Automation SystemAutomatic sliding mechanism with brushless DC motor,Microprocessor-based controller,Adjustable opening/closing speed' Soft start/stop and auto-reverse safety system,Infrared/motion sensor operationC. Sensors & SafetyMotion detection sensor (adjustable range),Safety sensor to prevent collision,Emergency/manual override systemD. Track & Frame SystemHeavy-duty aluminium track with anodized/powder-coated finish,Aluminium casing for motor housing,High-quality rollers and guidesE. Hardware & FittingsSS 304 grade fittings including patch fittings, brackets, connectors,Floor guides, stoppers, rubber gaskets, brush seals,All fixing accessories completeF. Electrical WorkComplete internal wiring with FRLS copper wire,Concealed conduit system,MCB protection and earthing,Integration with existing power supply |
| 54 | G. Installation, Testing & CommissioningComplete erection and installation, Alignment, sealing with siliconeTesting of sensors, motor, safety systems,Trial runs and commissioningApproved Makes :(1). Toughened Glass-Saint-Gobain / AIS (Asahi India Glass) / Modi Guard. (2). Automatic Door System (Motor & Controller)-Dorma / Hafele / Ozone / Geze.(3). Sensors (Motion & Safety)-Hikvision / Honeywell / Ozone / Dorma.(4). SS Hardware & Fittings (SS 304)-Jindal/Hafele / Ozone / Dorma.(5). Aluminium Sections / Tracks-Jindal Aluminium / Hindalco / Banco.(6). Access Control System (RFID/Card)-Hikvision / Matrix / eSSL / Honeywell.(7). UPS System-APC / Microtek / Luminous(8). Sealant / Adhesive- Dr. Fixit / Pidilite/Asian.(9). Electrical Wires (FRLS)-Polycab / Finolex / Havells.(10). MCB / Electrical Accessories- Achor/Legrand / Havells/EverdeyNotes:- Rate shall include all materials, labour, T&P, transport, taxesNothing extra shall be paid for cutting, wastage, fittings, or installationContractor must submit catalogues and shop drawings before execution and test certificate after execution. Warranty : Minimum 12 months |
| 55 | M&L for 15mm thick rendering in cement mortar 1:6 on walls of other than fair face even and smooth without using extra cement compete including taking down old cement plaster and all debries removing the outside of MOD land all as specified and directed. |
| 56 | M&L for preparation of new plastered/concrete surfaces of walls and applying two coats of oil bound distemper over one coat of primer, over 2mm thick white putty white or tinted upto 12 Metre height including necessary scaffolding etc complete all as specified and directed.Note:- Application of distemper shall be with the help of a roller only. |
| 57 | Taking down old cement plaster and all debries removing the outside of MOD upto 12 Metre height including necessary scaffolding etc complete all as specified and directed. |
| 58 | M&L for 15mm thick rendering in cement mortar 1:4 on walls of surfaces finished even and smooth without using extra cement Incl. water proofing compound upto 12 Metre height including necessary scaffolding etc complete all as specified and directed. |
| 59 | M&L for preparation of new plastered/concrete surface of wall/chajjas/facia and applying two coats of exterior emulsion paint over 2mm thick water proof wall care putty upto 12 Metre height including necessary scaffolding etc complete all as specified and directed. |
| 60 | M&L for Rendering 10 mm thick in cement mortar (1:4) on ceiling, parapet, chajjas, facias of building and finished the surface even and smooth without using extra cement, inc taking down existing plaster complete all as specified and directed by Engineer-In-Charge. . |
| 61 | M&L for preparation of new plastered /concrete surfaces of ceiling and applying two coat of oil bound distemper, white or tinted with 1 mm thick white putty) ) upto 12 Metre height including necessary scaffolding etc complete all as specified and directed. Note:- Application of distemper shall be with the help of a roller only. |
| 62 | M & L for complete removal of exiting suface treatment and provide two coat of exterior acrylic emulsion weather proof treatment over a coat of primer after rubbing with sand paper upto 15 Metre height including necessary scaffolding etc complete all as specified and as directed.Note:- Application of distemper shall be with the help of a roller only. |
| 63 | M & L for 3mm thick water proof wall care putty on external new/old plastered/ unplastered wall surfaces/ concrete surfaces including necessary scaffolding etc complete all as specified and as direct. |
| 64 | M & L for plaster of paris putty of 3 to 5 mm thickness over plastered surface to prepare the surface even and smooth. Including hacking out of existing plasterd surface and applying pop with straighter /aluminiumm funty in true level of all direction complete all as specified and directed. |
| 65 | M&L for preparation of old painted surface/previously untreated surface/old plastered/ unplastered/POP/ concrete surfaces of any description with help of sand paper apply two coat of plastic emulsion over a coat of primer on any girth or width, not otherwise described complete all as specified and directed. |
| 66 | Supply and Fixing for WPC Wall paneling/Lining coloured, texture consisting of 10 to 12 mm thick including PVC sheet fillet (U, C or L shape) by mean of solvent/ nails/ screws to make grid as per manufacturer instruction fixing on wall and including of taking down old PVC wall Panneling all as specified and directed. Note :- Make, Colour & texture Approved by GE. |
| 67 | M&L for prepare of cementous surface / wall tiles/concrete surface using mechanical means as per manufacturer instructions :- (a) Take Poly plastic fibre adhesive/ Eazeecoat Ultra and white cement in equal proportion & add 25% water in it to make the mix as per manufacturer instructions. Apply 1 coat of wall bind adhesive mixture to the cementous surface/ wall tiles/ concrete surface using a roller & brush as base coat.(b) Applying the double layer of glass fibre mesh of 60 GSM on base coat of vertical wall surface & apply two coat of above mixture of poly plastic fibre adhesive/ Eazeecoat Ultra with a roller & brush to cover the fibre mesh throughly. (c) Final & top coat apply with mixing ratio of poly plastic fibre/ Eazeecoat Ultra top coat & water & white cement as per manufacturer instructions and incl. finish the surface with help of water proof wall care putty/OBD/Plastic emulsion/exterior emulsion/CBP etc to match the surface.Note :- The poly fibre plastic/ Eazeecoat Ultra should have following characteristics :-(a) Resists positive hydrostatic presure of upto 14 bars.(b) Crack filling ability upto 45 mm.(c) Temp control upto 14 degree celcious on any surface like concrete roof, metal shed & for walls also.(d) High durablity to water, fire & UV rays covering climate condition to + 55 degree celcious.Make : Nerolac Perma/ European Paints & Chemicals/ Ever Paint. Note:- The wall treatment shall be done on wall tile/new cementous/concrete surface for proper bonding & requisite results. Surface to be treated shall be passed by Engr-in-Charge. |
| 68 | Treating soil along the external wall below concrete or masonry apron using chemical emulsion (Chlorophyriphos 20 EC conforming to IS 8944 or Imidacloprid 30.50 SC conforming to IS 16131 [Refer Table 1 on Sl. Page No. 2 of IS 6313 (Part 2) : 2013] @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and directed. |
| 69 | Taking down chowkhat or frame exc. 1.5 sqm but n.exc 4 sqm each without taking off shutter from the frame complete all as specified and directed. |
| 70 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) for frame, shutters of doors, windows(two or three track sliding/openable) & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, auminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 71 | Material and labour for aluminium composite panel sheet of 3mm thick which consists of 3mm thick thermoplastic core of anti-toxic LDPE sandwiched between 2 skins of 0.5mm thick aluminium foils with outer surfaces finished with 30 u PVDF and inner surface finished with a thin coat of polyester paint, fixed in panel to aluminium frame including all necessary frame work or powder coated snap beading and rubber gasket complete all as specified and directed.Make :- Alstone/ Alex panel/ Armstrong/ Euroboard. |
| 72 | Supply and fixing 4.80mm thick ordinary quality Frosted/Etched glass, fixed to aluminum frame work in panels not exc 0.5 Sqm in each pane, complete all as specified & directed. |
| 73 | Supply and fix 180mm size powder coated (any tint) aluminium \\"American Handle\\" fixed to aluminium door with suitable screws, complete all as specified and directed. |
| 74 | Supply and fixing brass mortice lock vertical type 100mm size, 6 lever fixed in aluminium shutter, complete all as specified and directed. |
| 75 | S&F 100 mm size but hinges medium weight stainless steel complete all as specified & directed. |
| 76 | S&F 150 mm size Aluminium, barrel tower bolt of extruded section complete all as specified & directed. |
| 77 | Supply and fix, Aluminium alloy, anodised, Sliding door bolts 200mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia, complete all as specified and directed. |
| 78 | S&F factory made of 18-19 mm thick WPC boarding with denasity of 650 Kg/cum with CNC cuttig of approved design/pattern fixed with screws to the frame work, complete all as specified & directed. |
| 79 | S&F 30mm wide anti skid self adhesive precautionry tape of approved patten fixed on floor, stairs, risers, door cill/any offsets complete all as specified and directed. |
| 80 | Supply and fix in repair Aluminium alloy, anodised, Sliding door bolts 200mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia, complete all as specified and directed. |
| 81 | Taking down carefully of point wiring (Light, fan, socket or power complete fittings such as switches, Ceiling roses, pendants, regulator, sockets, Bell push) removing from site of work and making good to the disturbed surfaces of walls/floors etc complete all as specified and directed. |
| 82 | M&L for point wiring using stranded copper conductor FRLS cable 1.5 Sqmm,PVC insulated unsheathed and including non mettalic rigid UPVC on surface casing caping patti conduit with all fittings medium grade including all fitting and accessories PVC modular terminal boxes with modular inner frame and outer cover plate of suitable size for mouting of modular switches sockets, fan regulators etc fastened with chromium plated screws and 1.5 Sqmm PVC insulated stranded copper conductor FRLS cable as continues earth wire connected to common earth dolly for one light/fan poin controlled by one switch including making good distubed surface ((i.e plastering ,one coat of putti and two coates of OBD paint ) complete all as specified and directed. |
| 83 | S&F in replacement of modular switch, 1 module single pole one way 6 Amp complete all as specified & directed. |
| 84 | S&F in replacement of Ceiling rose surface Bakelite 65 x 50 mm inluding UPVC two to three terminals complete all as specified & directed. |
| 85 | Supply and fix in repair exhaust fan 150 mm sweep at outer wall, 250 CMH, 22W, 1800 RPM, ABS plastic Body along with inbuilt PVC louvers (same make as Exhaust fan) PVC mesh net at inner wall complete suitable to work on AC, single phase, 230 Volts, 1100 RPM, 50 Hz supply and including connecting up with three core twisted flexible copper conductor cable of suitable size 0.75 Sqmm upto 1 metre including making good disturbed surface i.e plastering, one coat of putti and two coats of old bound distemper paint with matching existing surface) complete all as specified and directed. |
| 86 | Making Round Boring of size suitable for 150 mm sweep exhaust fan including making good disturbed surface (i.e plastering, one coat of putti and two coats of old bound distemper paint with matching existing surface) complete all as specified and directed. |
| 87 | Note :- Amount of credit of Rs. 8120.00 for retrieved materials is mentioned in Schedule of Credit of tender documents in pdf form which will be deducted offline while acceptance of tender. Please Enable Macros to View BoQ information |
