|
| 1 | Dismantling tile work in floors and roofs laid in cement Mortar including stacking material within 50 metres lead.15.23.1 For thickness of tiles 10 mm to 25 mm |
| 2 | Dismantling W.C. Pan of all sizes including disposal odismantled materials i/e malba all complete as per directions of Engincer-in- Charge. |
| 3 | Dismantling doors, windows and clerestory windows (steel or Wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :15.12.1 Of area 3 sq.metres and below |
| 4 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engincer-in-charge. |
| 5 | Dismantling old plaster or skirting raking out joints and cleaning thesurface for plaster including disposal of rubbish to the dumping groundwithin 50 metres lead. |
| 6 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level.5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 7 | Centering and shuttering including strutting, propping etc. and removalof form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers andcantilevers |
| 8 | Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources). |
| 9 | Renewing glass panes, with putty and nails wherever,necessary including racking out the old putty:14.5.1 Float glassanes of nominal thickness 4 mm(weight not less than 10kg/sqm |
| 10 | Renewal of old putty of glass panes (length) |
| 11 | Repair to plaster of thickness 12mm to 20 mm in patches oFarea 2.5 sqm and under, including cutting the patch in propershape, raking out joints and preparing plastering the wall surfacewith white cement based polymer modificd self curing mortar,including disposal ofrubbish, all complete as per the direction 0FEngincer-In-Charge. |
| 12 | Half brick masonry with common burnt clay F.P.S. (non modular)bricks of class designation 7.5 in superstructure above plinth levelup to floor V level.6 13.1 Cement mortar 1:3 (1 cement :3 coarsesand) |
| 13 | 12 mm cement plaster of mix :13.1.1 1:4 (1 cement : 4 finesand) |
| 14 | 15 mm cement plaster on the rough side of single or half brick wall of mix :13.2.1 1:4 (1 cement: 4 fine sand) |
| 15 | Providing and applying plaster of paris putty of 2 mmthickness over plastered surface to prepare the surface even and smooth complete. |
| 16 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :13.41.1 New work(two or more coats) over and including water thinnable primingcoat with cement primer |
| 17 | Finishing walls with Acrylic Smooth exterior paint of requiredshade :13.46.1 New work (Two or more coat applied @ 1.67 ltr/10sqm over and including priming coat of exterior primer applied @2.20 kg/10 sqm) |
| 18 | Providing and fixing white vitreous china pedestal type watercloset (European type) with seat and lid, 10 litre low level white’vitreous china flushing cistem & C.P. flush bend with fittings &C.l. brackets, 40 mm flush bend, overflow arrangement withspecials of standard make and Mosquito proof coupling of approvedmunicipal design complete, including painting of fittings andbrackets, cutting and making good the walls and floors whereverrequired :17.3.1 W.C. pan with ISI marked white solid plastic seatand lid |
| 19 | Providing and fixing wash basin with C.1. brackets, 15 mmC.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,19 fincluding painting of fittings and brackets, cutting and makinggood the walls wherever require:17.7.1 White Vitreous China Washbasin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 20 | Providing and fixing P.V.C. waste pipe for sink or washbasin including P.V.C. waste fittings complete. 17.28.2 Flexiblepipel7.28.2.1 32 mm dia |
| 21 | Providing and fixing M.S. grills of required pattern in framesof windows etc. with M.S. flats, square or round bars etc. includingpriming coat with approved steel primer all complete.9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. |
| 22 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :13.61.1 Two or more coats onnew work |
| 23 | Providing and fixing factory made uPVC door frame made of.uPVC extruded sections having an overall dimension as below(tolerance 1mm), with wall thickness 2.0 mm (+ 0.2 mm), cornersof the door frame to be Jointed with galvanized brackets andStainless steel screws, joints mitred and Plastic welded. The hingeside vertical of the frames reinforced by galvanized M.S. tube ofsize 19 X 19 mm and 1 mm (+ 0.1 mm) wall thickness and 3 nos.stainless steel hinges fixed to the frame complete as permanufacturer’s specification and direction of Engineer in-charge9.117.2 Extruded section profile size 42x50 mm |
| 24 | Providing and fixing to existing door frames.9.118.3 25 mmthick PVC flush door shutters made out of a one piece Multichamber extruded PVC section of the size of 762 mm X 25 mm orless as per requirement with an average wallthickness of 1 mm (+0.3 mm). PVC foam end cap of size 23x10 mm are provided onboth vertical edges to ensure the overall thickness of 25 mm. M.S.tube having dimensions 19 mm x 19 mm and 1.0 mm (+ 0.1 mm) is24 [inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top &Bottom edges of the shutter are covered with an end-cap of the size25 mm X 11 mm. Door shutter shall be reinforced with specialpolymeric reinforcements as per manufacturer’s specification anddirection of Engincer-in-charge to take up necessary hardware andfixtures. Stickers indicating the locations of hardware will be pastedat appropriate places |
| 25 | Brick work with common burt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level a up to floor V level in all shapes and sizes in :6.4.1 Cement mortar1:4 (1 cement : 4 coarse sand) |
| 26 | 8.31 Providing and fixing Ist quality ceramic glazed wall tilesconforming to IS: 15622 (thickness to be specified by themanufacturer), of approved make, in all colours, shades exceptburgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of step sand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointingwith grey cement slurry @ 3.3kg per sqm, including pointing inwhite cement mixed with pigment of matching shade complete. |
| 27 | Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to IS: 15622, of- approved make, in all colours and shades, laid on 20 mm thickcement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @3.3 kg/ sqm including grouting the joints withwhile cement and matching pigments etc., complete. 1.41.2 Size of Tiles 600*600 mm |
| 28 | Providing and laying Vitrified tiles in floor in differentsizes (thickness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to IS:15622, ofapproved brand & manufacturer, in all colours and shade, laid on20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointingwith grey cement slurry @3.3 kg/sqm including grouting the jointswith white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will bedone with the notch trowel, plier, wedge, clips of requiredthickness, leveling system and rubber mallet for placing the tilesgently and easily.11.41A.3 Glazed Vitrified tiles Matt/Antiskidfinish of size 1.41A.3.1 Size of Tile 600 x 600 mm |
| 29 | Providing and fixing glazing in aluminium door, window,ventilator shutters and partitions etc. with EPDM rubber / neoprenegasket etc. complete as per the architectural drawings and thedirections of engineer-in-charge . (Cost of aluminium snap beadingshall be paid in basic item):21.3.1 With float glass panes of 4.0 mmthickness (weight not less than 10kg/sqm) |
| 30 | Providing and fixing stainless steel ( Grade 304) railing madeof Hollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required) andfitting the same with necessary stainless steel nuts and boltscomplete, i/c fixing the railingwith necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of requiredsize, on the top of the floor or the side of waist slab with suitablearrangement as per approval of Engineer-incharge, (for paymentpurpose only weight of stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 31 | Providing and fixing aluminium work for doors, windows,ventilators and partitions with extruded built up standard tubularsections/ appropriate Z sections and other sections of approvedmake conforming to IS: 733 and IS: 1285, fixing with dashfasteners of required dia and size, including necessary filling up thegaps at junctions, i.e. at top, bottom and sides with required EPDMrubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engincer-in-charge.(Glazing, pancling and dash fasteners to be paid for separatcly)21.1.2 For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provision for fixingof fittings wherever required including the cost of EPDM rubber /neoprene gasket required (Fittings shall be paid forseparately)21.1.2.2 Powder coated aluminium (minimum thicknessof powder coating 50 micron) |
| 32 | Hacking of CC flooring including cleaning for surface etc.complete as per direction of the Engincer-in-Charge. |
| 33 | Providing and fixing on wall face unplasticised Rigid PVCrain water pipes conforming to IS : 13592 Type A, includingjointing with seal ring conforming to IS : 5382, leaving 10 mm gapfor thermal expansion,(i) Single socketed pipes.12.41.2 110 mmdiameter |
| 34 | Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for unplasticised Rigid PVC rainwater pipes conforming to IS : 13592 Type A, including jointingwith seal ring conforming to IS : 5382, leaving 10 mm gap forthermal expansion. 12.42.1 Coupler!2.42.1.2 110 mm |
| 35 | Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for Unplasticised Rigid PVC rainwater Pipes conforming to IS : 13592 Type A, including jointingwith seal ring conforming to IS : 5382, leaving 10 mm gap forthermal expansion.12.42.5 Bend 87.5°12.42.5.2 110 mm bend |
| 36 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal Stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includesJointing of pipes & fittings with one step CPVC solvent cement, Rmtrenching, refilling & testing of joints complete as per direction ofEngineer in Charge. External work 18.9.1 15 mm nominal dia Pipes |
| 37 | Providing and laying cement concretelike at or near ground level excluding the cost of centering,shuttering and finishing.4.4.1 1:144:3 (1 Cement: 1% coarse m3seni) derived from natural sources : 3 graded stoneaggregate 20 mm nominal size derived from natural sources) |
| 38 | Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade :13.62.1 Twoor More coats on new work over an under coat of suitable shadewith ordinary paint of approved brand and manufacture |
| 39 | Removing dry or oil bound distemper, water proofing cementpaint and the like by scrapping, sand Papering and preparing the m2surface smooth including necessary repairs to scratches etc.complete. |
| 40 | Cleaning and desilting of gully trap chamber, includingremoval of rubbish mixed with earth etc. and disposal of same, all Eachas per the direction of Engincer-in-charge. |
| 41 | Cutting holes of required size in brick masonry wall forfixing of exhaust fan including providing and fixing 300 mm diaPVC pipe conforming BIS-12818 and making good the same etc.complete as per direction of Engincer-in-charge. |
| 42 | 9.1 Providing wood work in frames of doors, windows, clerestorywindows and other frames, wrought framed and fixed in positionwith hold fast lugs or with dash fasteners of required dia & length m3(hold fast lugs or dash fastener shall be paid for separately).9.1.1Second class teak wood |
| 43 | Providing and fixing panelled or panelled and glazed shuttersfor doors, windows and clerestory windows, fixing with butt hingesof required size with necessary screws, excluding panelling whichwill be paid for separately, all complete as per direction of Engineer.in-charge. (Note:- Butt hinges and necessary screws shall be paid m2separately)9.5.1 Second class teak wood9.5.1.2 30 mm thick shutters Please Enable Macros to View BoQ information |
