|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 5 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 6 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor II level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately). |
| 10 | Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 15 mm wide and 15 mm deep groove |
| 11 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 12 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 13 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 14 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 15 | Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer- ncharge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage |
| 16 | Providing and fixing Victorians type of Garden bench both side of arm of Garden bench made of flora cast iron and having of back height of minimum 700 mm seating height of 375 mm (approx) . The length of bench be 1500mm and minimum overall weight is not less than 90KGS. |
| 17 | Providing & Fixing of 2 mm thick 0.30x0.15 Mt. Stainless steel plates on benches with name of Hon`ble area MLA and tighted with aluminium riviting on existing benches. |
| 18 | Providing and fixing of FOUR SEATER ARC SWING make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/KOOCHIE/HUGO or equivalent as approved by Engineer-in-Charge. size 6.5m x 1.5m (21.3ft x 5ft) (Product Area) with all necessary fixing arrangements. The technical specification of item as following:-• . Certificate: ISO9001:2015 Color: Multicolor for optional or customized & according to RAL shade. Packaging: Safety 3 layer packaging like 1st EPE Foam 2nd HDPE Film and 3rd is Stretch wrap. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. |
| 19 | Providing and fixing of DOUBLE ARC SWING make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/KOOCHIE/HUGO or equivalent as approved by Engineer-in-Charge. Product Area : 3.2m x 1.5m (10.5ft x 5ft) • Safe Play Area : 4.2m X 2.5m (13.8ft X 8.2ft) • Ideal For : 4-14 Years • Friends at a time : 2 Technical Specification: •Arc swimg frame :6000mm long 80NB Pipe bent in Single Piece & welded together with a flange 5mm thick & ISA of 40x40x5mm to form a strong frame. The 80NB pipe is hot dip galvanized pipe conforming to IS 1239 with GI thickness of 60μ. Height of the frame is 2700mm. •Top pipe : 50NB Top Pipe with two Arc Swing Flanges welded at both its ends. Pipe can withstanding torsional stress created due to swinging motion. . All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. |
| 20 | Providing and fixing of Multi seater See- Saw make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/KOOCHIE/HUGO or equivalent as approved by Engineer-in-Charge. • Product Area : 0.5m X 3m (1.6ft X 9.8ft) • All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. |
| 21 | Providing and fixing of Double WAVE SLIDE 2.1 MTR.. make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/KOOCHIE/HUGO or equivalent as approved by Engineer-in-Charge. • All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines. |
| 22 | Providing & Fixing of ANIMAL MGR make of Arihant : • Product Area : 2.1m Dia (7 ft Dia.) • Safe Play Area : 3.1m Dia (10.2 ft Dia.) • Ideal For : 3-12 Years • Friends at a time : 5 Technical Specification:•MGR frame : MGR Frame made from 40NB pipes welded together with bottom end over a circular plate meant for assembling bearing assembly. : All metal pipes are Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness upto 60micron. •Pipe Materials or Class: Light Duty ('A' Class) & Medium Duty ('B' Class) Series of pipes only. Wall thickness of pipe varies according to class / series of pipe used. |
| 23 | Providing and fixing of TRIPLE WAVE SLIDE 2.1 MTR. make of Arihant. The amazing triple wave slide is made up of FRP. At a time three children can enjoy sliding. The slide entry is mounted on 80 NB and 80 x 20 NB nylon clamp. The ladder frame is made in 20 NB and 25 NB powder coated GI pipes. The triangular steps are made in 16 SWG GI sheets. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer. Please Enable Macros to View BoQ information |
