|
| 1 | Dismantling timber scantling of sectional area above 40 sq cm and over in section, in any position framed / unframed work all as specified and directed. |
| 2 | Dismantling boarding ,any description, fixed in any position with nails all as specified and directed |
| 3 | Material and labour for Second class hard-wood in scantlings clean sawn fixed in position as required at site framed / unframed complete all as specified and directed. |
| 4 | Supply and fixing of 40 mm thick 2nd class hard wood Boarding, fixed with nails in any situation (except flooring and skirting) clean sawn with butt joints complete all as specified and directed. |
| 5 | Material and labour for preparing surface of wood and wood based materials, new or old ,of any description and girth, not otherwise described and treated with two coats of Creosote oil produced from the distillation of coal tar of approved make complete all as specified and directed. |
| 6 | Material and labour for filling of firing range butt with approved selected screened earth of required grading as per the site requirement approved by Engineer in charge brought from out side of MD land, in layers not exc 15cm thick, spread, leveled and rammed including watering as directed. |
| 7 | Demolition of cement concrete un reinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing to dumping areas earmarked inside INA complete all as specified and directed. |
| 8 | Demolition of cement concrete un reinforced of any description and in any position not otherwise specifically provided for and removing to dumping areas earmarked inside INA complete all as specified and directed. |
| 9 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition and removing to dumping areas earmarked inside INA complete all as specified and directed. |
| 10 | Material and labour for PCC 1:3:6 Type C-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed. |
| 11 | Material and labour for 100 mm thick plain Cement concrete 1:4:8 Type D- 2 using 40 mm graded stone aggregate as in sub base, sub floors etc complete all as specified and as directed. |
| 12 | Material and labour for 100 mm thick plain Cement concrete 1:2:4 Type B-1,using 20mm graded stone aggregate as in hard standing, floors/ pavings etc surface finished even and fair without using extra cement complete all as specified and as directed. |
| 13 | Material and labour for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete al as specified and directed. |
| 14 | Material and labour for Providing, cement concrete 1:2:4 Type B-1 using 20 mm graded stone aggregate in in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, at any height complete all as specified and directed. |
| 15 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 16 | Material and labour for reinforced Pre-cast cement concrete 1:2:4 Type B-1 using 20 mm graded stone aggregate as in cover slabs for man holes, drains, water throughs etc with plain fair faces including use of necessary form work and setting in cement mortar 1:4 complete all as specified and directed. Note: Reinforcement shall be measured and paid separately. |
| 17 | Material and labour Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, ending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 18 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water,etc.complete all as specified and directed. |
| 19 | Material and labour for Rendering 15mm thick in CM 1:4 on any faces of brick work or concrete surfaces finished even & smooth without using extra cement all as specified and directed. |
| 20 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removing to dumping areas earmarked inside INA complete all as specified and directed. |
| 21 | Material and labour for Pre-cast cement concrete block masonry 1:3:6 Type C1 (using 20 mm aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar (1:6) all as specified and directed. |
| 22 | Material & Labour for Finishing walls with Premium Acrylic Smooth exterior emulsion paint with Silicone additives of required shade on new work (Two or more coats applied @ 1.43 ltr/10 sqm or as per manufacturers instructions) over and including priming coat of exterior primer applied as per manufacturers instructions including preparation od surfaces complete all as specified and directed. |
| 23 | Material & Labour for Finishing walls with one coat of Premium Acrylic Smooth exterior emulsion paint with Silicone additives applied as per manufacturers instructions (including applying additional coats wherever required to achieve even shade and colour) of required shade on old work including preparation of surfaces complete all as specified and directed. |
| 24 | Material and labour for preparation of old decorated surfaces and applying one coat of interior premium acrylic emulsion paint of any colour on wall of concrete or plastered surface as per manufacturers instructions including filling depressions / holes etc wherever required with wall care putty and necessary scaffoldings all as specified and directed. |
| 25 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed. |
| 26 | Material and labour Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 27 | Supply and fixing of welded steel wire mesh having weight n.exc 4 Kgs/Sqm fixed on to MS frame with welded joints complete all as specified and directed. |
| 28 | Material and labour for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 29 | Material and labour for preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. Please Enable Macros to View BoQ information |
