|
| 1 | Dismantling of existing structures like culverts, bridges, retaining walls and other sturcture comprising of masonry, cement concrete wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable materials and stacking the serviceable materials with all lifts and lead of 1000m as per Technical Specification Clause 202 etc. complete & as per direction of the Engineer-in-Charge. |
| 2 | Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site by mechanical means, spreading, grading to required slope and compacting to meet requirement of table 300-2 & clause 305 of MoRTH specifications for Road & Bridge works (4th revision) etc complete as per specification & direction of Engineer-in-Charge. |
| 3 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement as per MORD technical Specification Clause 301 and direction of the Engineer in Charge (excluding cost of excavation and transportation to site). |
| 4 | Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m etc complete as per specification & direction of Engineer-in-Charge. |
| 5 | Construction of granular Sub base by providing close grade granular sub-base grading-III material as per table-100-1. spreading in uniform layers with motor grader om prepared surface,mixing by mix in place method with rotavator at OMC and compacting with vibratory roller to achieve the desired density complete as per clause 401 of MOSRT&H specifications for road and Bridges work. |
| 6 | Providing , Laying, spreading and compacting graded stone aggregates in Wet Mix Macadam as per specification including premixing material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site laying in uniform layers with paver in sub-base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406 of MORTH specifications for road & bridge works (4th revision) including cost conveyance required as directed by Engineer-in-Charge. |
| 7 | Construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub-base, with 43 grade cement or any other type as per Clause 1501.2.2, M30 (grade) coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the form work as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars near approaches to bridges and culverts (expansion joints), admixtures as approved, curing of concrete slabs for 14 days, curing compound and water finishing to lines and grade as per drawing and Technical Specification Clause 1501. |
| 8 | Earth work in excavation of fondation in hard soil within the initial lead & lift including dressing & levelling the bed & depositiong the excavated earth away from the site etc. all complete as per the direction of Engineer in Charge. |
| 9 | Filling sand-Supplying & filling good clean river sand of approved quality including watering to complete saturation & ramming complete with all leads & lifts including cost, conveyance, royalty & taxes of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge. |
| 10 | PCC M-15 grade in foundation bed using 40mm to 10 mm size crushed stone aggregates mixed by concrete mixer laying in layers and compacting by vibrator & all leads and lifts as per approved drawing & technical specification and as per section 1700& 2100 of MORTH specification for road and bridge works (latest revision) including cost conveyance etc required as directed by Engineer-in-charge. |
| 11 | Foundation |
| 12 | Sub-Structure |
| 13 | Plain Cement Concrete M20 nominal mix) in levelling course below open foundation of Head walls as per drawings & Technical Specification Clause 802,803,1109,1202,1203 of MoRD |
| 14 | Drain Bed |
| 15 | R.C.C work of M-25 grade with 20mm and down grade black hard granite stone chips including cost, conveyance, royalty & taxes of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge. |
| 16 | Deck Slab |
| 17 | Hunch |
| 18 | Supplying, fitting and placing HYSD bar reinforcement complete as per drawings and technical specification Clauses 1000 and 1200 of MoRD and as per direction of the Engineer-in-Charge. |
| 19 | Providing Weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 of MORD specification for Rural roads and as per direction of Engineer-in- charge. |
| 20 | Providing and laying reinforced cement concrete NP3 pipe for culverts jointing with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1100 of MoRD & as per direction of Engineer-in-Charge. |
| 21 | 1000 mm dia HPC |
| 22 | White washing two coats on parapet walls and tree trunks including preparation of surface by cleaning scraping etc. as per MORD technical specifications Clause 1915 as per direction of the Engineer in charge. |
| 23 | Construction of R.C.C. railing of M 30 grade in cast-in-situ with 12 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900 and 1208.3 |
| 24 | Providing and laying of Filter Media with Stone Crushed aggregates of 45mm size satisfying the requirements laid down in clause 2504.2.2. of MORTH Specifications to a thickness of not less than 600mm with smaller size towards the soil and bigger size. |
| 25 | R.C.C M-30 grade in wearing course using 20mm and down grade BHGCB chips of approved quality from approved quarry including hoisting lowering and laying in position in layers with proper packing and ramming by means of vibrator to proper slope and level including watering and curring with cost conveyance royality of all materials required for the work including all labour,T&P for the work etc complete in all respect as per the specification and direction of Engineer-in-charge. |
| 26 | Providing and laying boulder appron for bed protection & pitching on slopes with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301 & 1302 |
| 27 | Reinforced cement concrete M15 grade Kilometer stone/ local stone of standard design as per IRC:8 fixing in position including painting & printing etc. as per the drawing &technical specification clause 1703 of MoRD and as per direction of Engineer-in-Charge. |
| 28 | Ordinary Kilometer stone |
| 29 | 200 mm Stone (Precast) |
| 30 | Guard post |
| 31 | Providing and fixing of typical TRIP informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 of MoRD and as per direction of the Engineer-in-charge. |
| 32 | Providing and fixing of typical Citizen Information board as per MORD specification and drawing. Three MS plates of 50 x 5 mm. thick, back plate duty welded with 75 mm dia steel tubes back on edges as per drawings. The upper and lowe plate will be welded with MS flat iron frame of 50mm x 5 mm. The steel tubes dully embeded in cement concrete M-15 grade blocksw of 600mm x 600 mm x 750 mm below ground level. All MS will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with redimixed synthetic enamel paint of superor quality in required shade and colour. All selection of framed posts and steel tubes will be painted with primer and two coats of epoxupaint as per drawing Clause 1701 and Annexure - 1700.1. |
| 33 | Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701 and as per direction of EIC |
| 34 | Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 of MoRD and as per direction of Engineer-in-charge. |
| 35 | 800 mm X 600 mm rectangular |
| 36 | 90 mm equilateral triangle |
| 37 | Maintenance |
| 38 | Maintenance Cost of Projects Road for the 1st Year |
| 39 | Maintenance Cost of Projects Road for the 2nd Year |
| 40 | Maintenance Cost of Projects Road for the 3rd Year |
| 41 | Maintenance Cost of Projects Road for the 4rth Year |
| 42 | Maintenance Cost of Projects Road for the 5th Year Please Enable Macros to View BoQ information |
