Tender For Beautification Of Children Park Locate At Jalsar Pond Under Deoghar District, Deoghar-Jharkhand

TDR : 55433828

Tender Notice
BOQ

19 Days Left

Deoghar , Jharkhand

Tender Brief : Tender For Beautification Of Children Park Locate At Jalsar Pond Under Deoghar District

Document Fees
₹ 10000 /-

EMD
₹ 649000.0 /-

Tender Value
Refer document

Submission Date
01-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.
2	Filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).
3	Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
4	Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
5	Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
6	Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
7	Providing designation 112mm thick reinforced designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.
8	Providing randam rubble stone masonry in CM (1:6) in foundation and plinth with hammer dressed stone of less than 0.03 M3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening raking out joints to 20 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
9	Providing randam rubble stone masonry in CM (1:6) in superstructure including cost of screening of materials scaffolding raking out joints to 20 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
10	Providing Ashlar stone masonry in CM (1:6) in foundation and plinth with chisel dressed stone, cut to required size and shape and clean coarse sand of F.M. 2 to 2.5 including cost of screening, carriage of materials, raking out joints to 20 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
11	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
12	Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart)
13	Direction and Place Identification Signs upto 0.9 sqm Size Board.(Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with area not exceeding 0.9 sqm fixed over back support frame of min 35 x 35 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)
14	Direction and Place Identification Signs with size more than 0.9 sqm size Board.(Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with area exceeding 0.9 sqm fixed over back support frame of min 40 x 40 x 5 mm Angle mounted on two nos. of mild steel circular pipe 65 NB, 3.2mm thickness and 4.5m meter total height firmly fixed to the ground by means of properly designed foundation with M 25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)
15	Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. Rate per cum for grading-I Material
16	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)
17	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)
18	Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
19	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
20	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)
21	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
22	Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
23	Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform
24	Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)
25	Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
26	Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
27	Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases
28	Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges
29	providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)
30	providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.
31	10 mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}
32	12 mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})
33	16 mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})
34	Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate / square as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)
35	Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.)
36	Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.
37	Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
38	Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
39	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece
40	Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .
41	Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.
42	Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.
43	Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
44	Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
45	Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
46	Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.
47	Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)
48	Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
49	Providing two coat of oil bound distemper of approved shade and make over a primer coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding, washing floors and taxes all complete as per building specification and direction of E/I.
50	Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.
51	Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.
52	Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.
53	Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.
54	Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.
55	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
56	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80 x 1.25 mm M.S. laths with 1.25 mm thick top cover.
57	Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
58	Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin-Charge. 80 mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.
59	Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement
60	Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement
61	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand): 25 mm thick
62	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
63	40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. Red sand stone
64	40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. White sand stone
65	Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
66	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes.
67	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
68	Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
69	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primerapplied @ 2.20 kg/ 10 sqm)
70	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
71	Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kg/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litre/10 sqm, complete as the direction of Engineer -in-Charge.
72	Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in-charge: Profile B, Fixing with adjustable lugs with split end tail to each jamb
73	Providing & Fixing decorative high pressure laminated sheet of plain I wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick
74	Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm f or Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc.
75	After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.
76	Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed>45 m/sec as per IS 875-Part 3 (ii) Sites with structure height more than 20 m for all wind speeds
77	Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).
78	Providing and fixing Float glass panes of nominal thickness 4 mm (weight not less than 10 kg/sqm) as per design approved by Engineer-in-Charge.
79	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish, Size of Tile 600 x 1200 mm
80	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
81	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red. Area of slab over 0.50 sqm.
82	Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade.
83	Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).
84	Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately).
85	Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size ) over 75mm bad by dry brick ballast 40mm nominal size well rammend and consolidated and grouted with fine sand including finishing the top smooth.
86	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
87	75 mm diameter
88	110 mm diameter.
89	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
90	Single tee without door 75x75x75 mm
91	Single tee without door 110x110x110 mm
92	Bend 87.5° 75 mm
93	Bend 87.5° 110 mm
94	Shoe (Plain) 110 mm
95	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
96	75 mm
97	110 mm
98	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work, Exposed on wall
99	25 mm nominal dia Pipes
100	32 mm nominal dia Pipes
101	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
102	15 mm nominal dia Pipes
103	20 mm nominal dia Pipes
104	Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.
105	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
106	For fixed portion, Powder coated aluminium (minimum thickness of powder coating 50 micron)
107	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
108	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)
109	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia
110	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.100 mm nominal size dia
111	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge.
112	Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge
113	Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge
114	Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \\"V\\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge
115	Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of : 200 mm dia
116	Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp
117	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).
118	Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm
119	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) &
120	900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick
121	Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.
122	Group A
123	Group C
124	Power Plug wiring in PVC Conduit (2X4 Sq.mm) :-Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.
125	S/F Ceiling Rose :- Supplying and fixing 2 pin 5 amp. ceiling rose on the existing junction box/ wooden block including connection etc. as required.
126	Supplying and fixing batten/ angle holder including connection etc. as required.
127	Supplying and fixing of 9/10 Watt LED Bulb including connection etc. as required.
128	Supplying and fixing of 15/16 Watt LED Bulb including connection etc. as required.
129	S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270 V AC, 50Hz. Luminarie shall be confirm to IS:10322 part 5/ section-5 and shall be complete with all neccssary accessories as required. 150/160 W LED Flood light.
130	S.I.T.C of following rating surface mounted LED tube light fitting suitable for 230V 50Hz, single phase supply etc. complete as required. 20W / 22 W LED tube
131	Supplying and fixing of 16\\" (400mm) Wall mounted fan with all necessary accesories as required.
132	S/F Modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc as required.
133	Supply, Installation, Testing and Commissioning of following size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of stranded length (upto 30 cm) with 1.5 1.5 sq.mm FR PVC insulated, copper wire suitable for 230 V 50 Hz, single phase supply etc. complete as required. 1200 mm (48\\") BLDC, 5 Star rating 32 W Ceiling Fan.
134	S/F light plug point with modular type accessories :-Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc, as required.
135	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch, connection painting etc, as required.
136	Supplying and fixing 20 amps 240V, SPN industrial socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps \\"C\\" curve, SP MCB insheet steel enclosure on surace or in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc.
137	Supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.
138	4/5 module (78mm x 140mm x 50mm)
139	6 module (78mm x 205mm x 50mm)
140	8/9 module (78mm x 230mm x 60mm)
141	12 module (135mm x 205mm x 60mm)
142	Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.
143	Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in surfacce/ recessed PVC conduit as required.
144	2 x 1.5 Sqmm + 1x1.5 sq.mm earth wire
145	4 x 10 sq. mm + 2 x 6 sq.mm earth wire
146	2 x 4 sq. mm + 1 x 4 sq.mm earth wire
147	2 x 2.5 sq. mm + 1 x 2.5 sq.mm earth wire
148	4 x 6 Sqmm + 2x6 sq.mm earth wire
149	S/F modular type switch/socket :- Supplying and fixing following modular tyep switch/socket on the existing modular plate & switch box including connections etc. as required.
150	5/6 amps, one way switch
151	5/6 amps, 3 pin socket outlet
152	Earthing with G.I. earth pipe 4.5mtr. long 40 mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.
153	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc., as required.
154	Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping and with 2 stes of G.I. nut bolt & spring washer spaced at 50 mm)
155	Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
156	Earthing with G.I. earth plate 600mm x 600mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.
157	P/F G.I. lightning conductor tape in horizontal run :-Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (horizontal run).
158	P/F G.I. lightning conductor tape in vertical run :-Providing and fixing G.I tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (vertical run).
159	Layrng earth tape for lightning conductor :-Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
160	Supply of following sizes and core PVC/XLPE insulated, PVC sheathed armoured electrical cable with aluminium conductor for working voltage upto 1.1 KV etc as required.
161	70 sq.mm, x 3.5 core
162	95 sq.mm, x 3.5 core
163	16 sq.mm, x 4 core
164	10 sq.mm, x 4 core
165	Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size not exceeding 35 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
166	Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 35 sq.mm. but not exceeding 95 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.
167	Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 95 sq mm but not exceeding 185 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
168	1.1 KV Cable End Termination :- Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.
169	3.5 X 70 sq. mm (38mm)
170	3.5 X 240 sq. mm (62mm)
171	4 x 16 sq.mm (28mm)
172	4 x 10 sq.mm (25mm)
173	Supplying and fixing following way three pole & neutral ,sheet steel, MCB distribution board, 415 volts, onsurface /recess, complete with tinned copper bus bar, neutral bus-bar, earthbar ,dinbar, interconnections, powder painted including earthing etc. as required. 6 Way (4+18) Double Door, Horizontal type
174	S/F 'B' series, S.P. MCB :-Supplying and fixing 6 amps to rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as required.6/32 amps, single pole \\"B\\" series
175	Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10kA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connection, testing & commissioning etc. as required.
176	50/63 amps. TPN.
177	40 amps. TPN.
178	6/32 amps, SPN
179	Supplying and fixing following rating four pole, (three phase and neutral) 415 volts, residual circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connection, testing & commissioning etc. as required.
180	16/25 amps.
181	40 amps
182	S.I.T.C. of following rating approval make LED Bollard fitting with cylindrical shape of height 600 to 850mm power input-8/9 watt with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, confirming to IS:10322 part 5 etc all complete as required. (excluding plinth charge)
183	S.I.T.C. of following rating approval make LED Bollard fitting with cylindrical shape and inverted cone shape head of height 600 to 850mm power input-8/9 watt with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, confirming to IS:10322 part 5 etc all complete as required. (excluding plinth charge)
184	S.I.T.C of following rating LED Street lighting luminarie with pressure die cast housing and thoughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC, 50 Hz. Luminarie shall be confirmed to IS: 10322 part-5/section-3 and shall be complete with all necessary accessories as required.
185	45/48 W LED Street light
186	70/72 W LED street light
187	Supply, Installation, Testing and Commissioning of following size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of stranded length (upto 30 cm) with 1.5 1.5 sq.mm FR PVC insulated, copper wire suitable for 230 V 50 Hz, single phase supply etc. complete as required. 1200 mm (48\\") Ceiling fan
188	Supply, Installation, Testing and Commissioning of 9 Mtr. height Octagonal Hot - Dip galvanized pole( BOP - 9031) with top dia 70 mm, bottom dia 130 mm & made of 3 mm thick sheet, base plate dimensions 200 X 200 X 16 mm ( Lx BxT) including suitable sizes of foundation bolt all complete as reqd. (Without Arm)
189	Supply, Installation, Testing and Commissioning of 1 m single arm suitable for 70mm top
190	Supply, Installation, Testing and Commissioning of 1 m double arm suitable for 70mm top
191	Installation, Testing & Commissioning of the 9 Mtr. Octagonal PoIe & light fitting with the help of suitable tool and plants, and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10 T/mtrs sq. but excluding wire and MCB.
192	Supply and installation of 12mtr. High mast in one section Construction S355 grade as per BS-EN 10 025 Top Dia 100mm, bottom dia 360mm, plate thickness 3mm, 12 side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike Lighting protection, maximum wind speed 47m/ s as per IS : 875 (Part-III) with 6 nos foundation bols of PCD 445mm TS 600/ 24mm dia/850 mm long. Luminaries carriage : Material for 40 NB ERW Class B - M.S. Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded, 2 sections having carrying capacity upto 8 luminaries. Trailing Cable : 5 core 2.5sq.mm. PVC flexible copper conductor Winch/Power Tool : Double drum, SWL 350 kg with 0.75HP 6 pole single speed integral motor Rope : Grade AISI 304, 7/19 construction, dia 5mm, BLC 1450 x 2 having 2 nos of continues rope. Aviation obstruction light: twin dome aviation obstruction lights LED type as required. (But excluding Feeder Pillar).
193	Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. Not less than 350 gms.) with extra socket all complete as per specification and direction of E/I.
194	Providing and fixing 15mm size C.P. Brass piller cock (weight not less than 350gms). C.I. Body brass spindle pillar cock of approved quality as per specification and direction of Engineer-in charge. C.I. Body brass spindle
195	Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I. 15 mm dia
196	Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.
197	Horizontal non-return valve32 mm dia weight not less than 600 gms.
198	Vertical non-return valve 25 mm dia weiqht not less than 375 gms.
199	Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580 mm long. with 10.00 lit. Low level PVC Cistern.
200	Supplying fitting and fixing 40mm high vitreous white glazed earthen E.W.C. With 'P' trap of parry hindustan or any other approved I.S.S. Make including supplying and fixing 15 litres C.I. Mosquito proof low down flushing cistern of approved make with complete fittings With C.I. handle and R.S. or bracket with telescope flush pipe with brass coupling and plumbers joints spindle stop cock of approved uality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved pain over a coat of red oxide priming all complete as per specification and direction of E/I. E.W.C. With 'S' trap. 10.00 lit. Low level PVC Cistern.
201	Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms. 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.
202	Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I.150 mm dia RCC spun pipe, Upto 3.0 metre depth of invert below G.L.
203	Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I.150 mm dia
204	DT : Basic rates for 125/115 mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.Drilling upto 30 mtr. Depth below G.L.
205	HYDT :-Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.
206	From 0.00 Metre to 50.00 Metre
207	From 51.0 Metre to125.00 Metre
208	Supplying submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 +- 10%, 3PH, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/ Noryl Impeller) up to 20 stages (2 HP)
209	Supplying fitting and fixing of FR PVC insulated 3 core 4 sq.mm copper wire.
210	Supply fitting and fixing of G.l. Pipes (TATA mark or equlvalent) as per IS-1239 (part-01) 2004 ISI Marked / Medlum Quality all complete job as per direction of E/I. 40 mm dia.
211	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm
212	Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of Hindustan \\"Parry\\" or any other approved I.S.S. Make with 5 liters capacity C.I. Automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. bracket, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm P.V.C./Alkthene pipe 450 mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I. Flat back or standing corner (600 mm x 350 mm)
213	Supplying materials and labours for constructing inspaction chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimention having 250mm wall thickness in cement morter (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 36kg.) alongwith earth work in excavation and 80 mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.
214	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
215	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
216	Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
217	Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm
218	Fine dressing of the ground
219	Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
220	Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
221	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
222	Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light, watering with sprinkler and maintenance for 30 days or more till the grass establish properly as per direction of officer-in-charge.
223	Providing & laying of Selection no. 1 Doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same and maintenance for 30 days or more till the grass establish properly, as per direction of the officer-in-charge.
224	Providing, stacking and Displaying Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of Bucket type cement pot and as per direction of the officer-in-charge.
225	Providing, stacking and Displaying Araucaria cookie plant, having ht. 90 cm to 120 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 25 cm size of earthen pot/plastic pot and as per direction of the officer-in-charge.
226	Providing and Displaying plants Allyssum white in full bloom well developed Fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
227	Providing and Displaying plants Petunia hybrid different variety in different colour well developed with fresh and healthy foliage in full bloom in 25 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.
228	Providing and Displaying plants Dahlia double kenya variety in different colour well developed with 3 to 4 flowers in half bloom, good foliage stacked with Green painted Bamboo sticks, 45 to 60 cm height in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
229	Providing and Displaying plants Dianthus dwarf in different colour fresh & healthy bloom in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
230	Providing and Displaying plants Marigold jaffri orange/ yellow/ Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
231	Providing and Displaying plants Missbranthemum in different colour well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.
232	Providing and Displaying plants Nasturtium in different colour well developed with fresh & healthy foliage with full bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge..
233	Providing and Displaying plants Verbina in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
234	Supply and stacking of plant Cassia biflora of height 60-75 cm. with 4-5 branches in poly bags of size 25 cm as per direction of the officer-in-charge.
235	Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
236	Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.
237	Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.
238	Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.
239	Carriage of materials including loading at source, unloading at works site and stacking properly, labour, etc. all complete as per direction of E/I.
240	Stone Chips
241	Bricks
242	Stone Metal
243	Non Schedule
244	Outdoor Feeder Panel ( for street light and High mast): Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 , 6 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.
245	Incomer : 1 No. 100A/FP/16kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. Outgoings: MCB 40 A, TPN, 10kA - 6 nos. for highmast, street lights & bollard lights, 40 amp 4P Duty contactor,0-24hrs Timer switch with bypass arrangement100 amp 415 V heavy duty three phase with neutral busbar chamberIndicator switch, selector switches, CT, PT, RYB Lamps and Voltmeter, Ammeter etc
246	Supply and installation of Cast Iron Powder Coating Garden Bench approved quality as per specification and direction of E/I.
247	Supply and installation of jumping jack jhula approved quality as per specification and direction of E/I.
248	Supply and installation of Air Walker/ Stroller Double approved quality as per specification and direction of E/I.
249	Supply and installation of Air Walker/ Stroller Single approved quality as per specification and direction of E/I.
250	Supply and installation of Chest Press Double approved quality as per specification and direction of E/I.
251	Supply and installation of Double Surf Board approved quality as per specification and direction of E/I.
252	Supply and installation of Single Surf Board approved quality as per specification and direction of E/I.
253	Supply and installation of Leg Press approved quality as per specification and direction of E/I.
254	Supply and installation of Parallel Bar approved quality as per specification and direction of E/I.
255	Supply and installation of Three Wheel Shoulder Builder/ Arm Wheel approved quality as per specification and direction of E/I.
256	Supply and installation of Two Wheel Shoulder Builder/ Arm Wheel approved quality as per specification and direction of E/I.
257	Supply and installation of Triple Twister (Three standing) Twister approved quality as per specification and direction of E/I.
258	Supply and installation of Gazebo approved quality as per specification and direction of E/I.
259	Supply and installation of Fountainapproved quality as per specification and direction of E/I.
260	Supply and installation of Statue Ashoka Pillar approved quality as per specification and direction of E/I.
261	Supply and installation of Statue ELEPHANT approved quality as per specification and direction of E/I.
262	Supply and installation of SUN ENERGY INDIA ENTERPRISES 12 Watt WHITE-LED BASED SOLAR STREET LIGHTING SYSTEM With 30 Ah Battery Capacity
263	Supply & delivery of FOH Speaker with following specification:-2-Way Loudspeaker System with 1 x 15” LF, Rotatable waveguide for vertical or horizontal orientation, Bi-Amp/Passive Switchable, Frequency Range : 34 Hz - 20 kHz, Coverage Pattern : Horizontal 90 degree, Vertical 50 degree, Bi-amp/Passive switchable: 2 kHz, Transducer Power :LF (4000 W peak) , HF (400 W peak), Nominal Impedance: 8 ohms, Maximum SPL HF:141 dB peak , Passive mode:130 dB peak, System Sensitivity (1W @ 1m): Passive mode: 96 dB SPL, Grille: Powder coated 14 gauge perforated steel, with acoustically transparent black foam backing, should support Suspension from ceiling with all accessories.Make: JBL/ Martin/ Meyer or Equivalent.
264	Supply & delivery of FOH Speaker with following specification:-2-Way Loudspeaker System with 1 x 15” LF, Rotatable waveguide for vertical or horizontal orientation, Bi-Amp/Passive Switchable, Frequency Range : 34 Hz - 20 kHz, Coverage Pattern : Horizontal 120 degree, Vertical 60 degree, Bi-amp/Passive switchable: 2 kHz, Transducer Power :LF (4000 W peak) , HF (400 W peak), Nominal Impedance: 8 ohms, Maximum SPL HF:141 dB peak , Passive mode:130 dB peak, System Sensitivity (1W @ 1m): Passive mode: 96 dB SPL, Grille: Powder coated 14 gauge perforated steel, with acoustically transparent black foam backing, should support Suspension from ceiling with all accessories.Make: JBL/ Martin/ Meyer or Equivalent.
265	Supply & delivery of Subwoofer with following specification :-High Power Subwoofer 2 x 18\\", Frequency Range: 28 Hz – 1 kHz, Power Rating :9600W Peak, Maximum SPL 30 to 500HZ =142 dB Peak, Sensitivity 30 to 500HZ =102 dB Peak, Nominal Impedance: 4 ohms, Input Modes: Drivers Parallel / Drivers Discrete.Make: JBL/ Martin/ Meyer or Equivalent.
266	Supply & delivery of Front Fill Speaker with following specification:- 2‐Way Loudspeaker, Shall have Frequency Range: 58 Hz - 20 kHz (-10 dB), Frequency Response: 68 Hz – 19 kHz (±3 dB) , Coverage Pattern- 120° x 60° , System Sensitivity (dB-SPL, 1W @ 1m)-92 dB, Maximum SPL: 113 dB, Nominal Impedance: 8 Ohms, Power Handling (Programme):500W.Make: JBL/ Martin/ Meyer or Equivalent.
267	Supply & delivery of Delay Fill Speaker with following specification:- 2-Way Loudspeaker System with 1 x 12” LF, Frequency Range (-10 dB): 36 Hz – 20 kHz, Frequency Response(±3 dB): 43 Hz – 18 kHz ,Coverage Pattern: 120° x 60°, Crossover Modes: Bi-amp/Passive switchable ,Passive Crossover Frequency: 1.5 kHz ,Transducer Power Rating: LF: 4000 W peak,HF: 400 W peak, Bi-amp mode SPL LF: 128 dB peak, HF: 141 dB peak ,Passive mode SPL: 129 dB peak, System Sensitivity (1W @ 1m) Passive mode: 95 dB SPL ,Low Frequency Driver: 1 x 12 in driver with 50.8 mm (2 in) dual voice coil ,High Frequency Driver: 1x (1.5 in) compression driver, (1.5 in) voice coil, Enclosure: Trapezoidal with 15 degree side angles ,Suspension Attachment: 15 points (10MM), Grille: Powder coated 14 gauge perforated steel, Input Connector: NL4 Neutrik Speakon and CE-compliant covered barrier strip terminals.Make: JBL/ Martin/ Meyer or Equivalent.
268	Supply & delivery of Amplifier with following specification :- Multichannel Digital Network Based Power Amplifier with Power output 4 x 600W @ 4 Ohms / 8 Ohms,Eight-channel Audio amplifier , 8x 600W at 4 and 8 Ohm, 70Vrms and 100Vrms output on all Eight channels, THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel, bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ 45 port, 1 Ethernet R 45 port for monitoring and configuration , Should have Limiters, Input/output EQ, Delay, Matrix Mixer, Speaker Line Monitoring, Damping Factor (20 Hz to 100 Hz) : >1000Approved Make: Crown/ Labgruppen/ Powersoft or Equivalent.
269	Supply & delivery of Amplifier with following specification :- Multichannel Digital Network Based Power Amplifier with Power output 4 x 1250W @ 4 Ohms / 8 Ohms,Eight-channel Audio amplifier , 8x 600W at 4 and 8 Ohm, 70Vrms and 100Vrms output on all Eight channels, THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel, bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ 45 port, 1 Ethernet R 45 port for monitoring and configuration , Should have Limiters, Input/output EQ, Delay, Matrix Mixer, Speaker Line Monitoring, Damping Factor (20 Hz to 100 Hz) : >1500.Make: Crown/ Labgruppen/ Powersoft or Equivalent.
270	Supply & delivery of Amplifier with following specification :- Power Amplifier, Input Channels : 2 or better Power output: 3000 watts 2 ohm stereo per ch, 2100 watts 4 ohm stereo per ch, 1200 watts 8 ohm stereo per ch, 4200 watts 8 ohm bridge-mono, 6000 watts 4 ohms bridge-mono or better, Sensitivity (for full rated power at 4 ohms): 1.4V RMS or better, Frequency response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB or better, S/N Ratio (below rated 1 kHz power at 8 ohms): 103 dB or better, THD: <0.5% or better, Damping factor (20 Hz to 1 kHz):> 500 or better, Crosstalk (below rated power): 20 kHz - 1 kHz: >70 dB or better Input impedance(nominal):20k ohms balanced,10k ohms unbalanced or better, Maximum input signal: +22 dBu typical or better.Make: Crown/ Labgruppen/ Powersoft or Equivalent.
271	Supply & delivery of DSP with following specification :- 12 x 8 Networked Digital Signal Processor DSP with 4 Analog Inputs (with 48v Phantom Power per Channel), 4 Analog Outputs, Configurable Signal Processing, Rich Palette of Processing and Logic Objects, 48 Channel, Low Latency, Fault Tolerant Digital Audio Bus, Clear Front Panel LED Indication, Bi-Directional Locate Functionality, 12 Control Inputs and 6 Logic Outputs for GPIO Integration, Soundweb London Interface Kit for Third Party, Control System Integration HiQnet Device, Configuration, Control and Monitoring from Software, 12-48VDC or PoE+ Powering Options, (12VDC Power Supply Included), Rack Mount, Surface Mount and Desk Mount.Make: BSS/ BiAmp/ Symetrix or Equivalent.
272	Supply & delivery of DSP Expander with following specification :- 4 Analog Inputs (with 48v Phantom Power per Channel), 4 Analog Outputs, Configurable Signal Processing, Rich Palette of Processing and Logic Objects, 48 Channel, Low Latency, Fault Tolerant Digital. Audio Bus, Clear Front Panel LED Indication, Bi-Directional Locate Functionality, 12 Control Inputs and 6 Logic Outputs for GPIO, Integration, Soundweb London Interface Kit for Third Party, Control System Integration (Documentation), HiQnet Device, Configuration, Control and Monitoring from Software, 12-48VDC or PoE+ Powering Options, (12VDC Power Supply Included), Rack Mount, Surface Mount and Desk Mount.Make: BSS/ BiAmp/ Symetrix or Equivalent.
273	Supply & delivery of Equlizer with following specification:-Dual Channel 31-Band Equalizer, Shall have Dual 31-band, 1/3-octave Constant Q frequency bands with Switchable boost/cut ranges of ±6 or ±12 dB , Front panel bypass switch , ±12 dB input gain range , 4-segment LED ladders for monitoring output levels, XLR and TRS Inpts and Outputs Frequency Response of <10Hz to >50kHz ,Dynamic range of greater than 108dBApproved Make: dbx/ BSS/ Klark Teknik or Equivalent.
274	Supply & delivery of Digital Mixing Console with following specification :- Digital mixer with 32 mono mic inputs, 4 line inputs, 4 Stereo Lexicon Effects engines, 20 sub-group / aux busses, Mic Input to Line Output +0/-1dB, 20Hz – 20kHz, Mic Input E.I.N. 126dBu (150Ω source), 4 Fx Busses & 8 Matrix Busses, Delay on inputs and outputs, Colour touch screen interface.Make: Soundcraft/ Yamaha/ Allenheath or Equivalent.
275	Supply & delivery of Interconnects & Connectors:- Interconnects & Connectors consiting of XLR,Speakons, TRS etc . Approved Make: Neutrik / Amphenol / MX or Equivalent.
276	Supply & delivery of Speaker Cable:-Speaker cable - 2 X 2.5 sq.mm & 2 x 4.0 sq. mm (Lot) Make: Krystal / Finolex / Sommer or Equivalent.
277	Supply & delivery of Bracket for FOH & Front Fill, Delay Fill Etc:- racket for FOH & Delay Speakers Make: Customised or Equivalent.
278	Supply & delivery of Equipment Rack:- 36U Equipment Rack Make: Comrack / Valrack / President or Equivalent.
279	Supplying, installing, testing and commissioning of Dome camera 1/2.8\\" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 50m IR, 0.001Lux, 1920x1080@30fps, 512 GB SD card slot, IP67, IK10, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal HousingMake : Pelco/ Birdeye/ Axis or Equivalent.
280	Supplying, installing, testing and commissioning of Bullet camera 1/2.8\\" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 80m IR, 0.001Lux, 2592x1944@30fps, 2MP@60fps, 512 GB SD card slot, IP67, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing.Make : Pelco/ Birdeye/ Axis or Equivalent.
281	Supplying, installing, testing and commissioning of PVC Junction Box
282	Supply, Installation, Testing & Commissioning of 43\\" Commercial display built in Android OS
283	Supply, Installation, Testing & Commissioning of Server Grade Machine with Minimum 3 Ghz Processor, 8 GB RAM, 1 TB Hard disk along with necessary as required.
284	Supply of Surveillance Hard Disc Drive 6TB, Make : Seagate/ WD/ Toshiba or Equivalent.
285	Supply, installation testing and commissioning of 32 channel NVR with 1080p real-time live view H.265/H.264 MJPEG dual codec decoding Up to 12 MP resolution preview & playback max 320 MBPS incoming bandwidth support 4 SATA HDDs up to 32TB, supports ﬁsheye video de-warping in local and web user interface, supports visual or auditory notiﬁcations(a ﬂashing light, bell, or siren) complete with UL certiﬁcation
286	Add GST 18 %
287	Add Labour cess 1% Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Jharkhand Tenders

Services Tenders

Space Planning And Designing Tenders

Gardening Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Beautification Of Children Park Locate At Jalsar Pond Under Deoghar District, Deoghar-Jharkhand

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Beautification Of Children Park Locate At Jalsar Pond Under Deoghar District, Deoghar-Jharkhand

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us