|
| 1 | Earth work in excavation in foundations, trenches, pits, areas including dressing of sides and ramming of bottom wherever, required, lift upto 1.5 M, getting out excavated earth, disposal of surplus excavated earth upto a lead of 10 M: |
| 2 | a) Soft/loose/hard/dense soil |
| 3 | b) Ordinary rock /Hard rock without blasting |
| 4 | Surface dressing of the ground including removing inequalities not exceeding 15 cm deep and disposal of rubbish anywhere within plant area in soft/loose soil. |
| 5 | Filling available material vis. earth/sand/moorum/farm yard manure/stone aggregate etc., and spreading, levelling the same, watering and consolidation wherever required in pits, trenches, sides of foundations, flower beds/lawns, planted areas etc. as per directions of Engineer-in-Charge |
| 6 | Transportation of surplus earth, material, store items, garbage, plant construction debries, plants, saplings etc., anywhere in factory area including loading, unloading to work site, dump yard as per the directions of Engineer-in-Charge,excluding spreading and levelling thedisposed off materials: |
| 7 | a) By truck / tractor trolley / hand cart on the basis of measured work |
| 8 | By engaging tractor trolley of size 2.95 x 1.75 x 0.53 mtr including driver and 4 (four) number of labour with tools and fuel for transportation of materials on the basis of per day ( 8 hrs.) working |
| 9 | Supplying and stacking at site of following materials :Coarse sand,Fine sand,Moorum,Stone aggregate of approved quality |
| 10 | Providing and laying cement concrete in foundation, footing, sub bases of pavements, floors, beds excluding cost of centring and shuttering complete : |
| 11 | 1:4:8 (1 cement:4 coarse sand: 8 graded stone aggregate 40 mm nominal size) |
| 12 | 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate |
| 13 | Making plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20/12.5 mm size) parapet/banni upto 50 x 50 mm including centering and shuttering complete |
| 14 | Providing and laying reinforced cement concrete work excluding centering, shuttering and reinforcement in a) Foundations, footings, rafts, columns, pedestals,plinth beams, manhole chambers,flooring,pavements etc. |
| 15 | i) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20/12.5 mm size) |
| 16 | ii) 1:1.5:3 (1 cement : 1.5 coarse sand ; 3 graded stone aggregate 20/12.5 mm size) |
| 17 | Providing and laying cement concrete in foundation, footing, sub bases of pavements, floors, beds excluding cost of centring and shuttering complete : |
| 18 | i) 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20/12.5 mm size) |
| 19 | ii) 1:1.5:3 (1 cement : 1.5 coarse sand ; 3 graded stone aggregate 20/12.5 mm size) |
| 20 | Cutting , bending, hoisting and fixing in position reinforcement for RCC work at all heights and depths (mild/ tor steel). |
| 21 | Providing, fixing and removing centring and shuttering including strutting, proping etc. complete:a) In foundations, footings, bases of columns, rafts, pavements etc. |
| 22 | Providing, fixing and removing centring and shuttering including strutting, proping etc. complete b) In super structure i.e. in columns, beams, cantilivers,shelves, slabs, landing, vertical/horizontal fins etc. |
| 23 | c) Making pockets upto 200x200x200 mm in RCC/PCC |
| 24 | d) -do- in Brick/stone work |
| 25 | Brick work with local bricks of class designation 50 in foundations and plinth in 1:6 mortar (1 cement: 6 coarse sand). |
| 26 | Brick work with local bricks of class designation of 50 insuper structure in 1:6 mortar (1 cement : 6 coarse sand). |
| 27 | Half brick masonary with local bricks of designation 50 infoundation and plinth in 1:4 mortar (1 cement : 4 coarse sand). |
| 28 | Randum Rubble Masonary with hard stone in foundation and plinth including levelling up with cement concrete 1:6:1220/12.5 mm size) at plinth level in cement mortar 1:6 ( 1 cement : 6 coarse sand).(1 cement : 6 coarse sand : 12 graded stone aggregare |
| 29 | 15 mm thick cement plaster 1:6 ( 1 cement : 6 fine sand). |
| 30 | 12 mm thick cement plaster 1:6 (1 cement : 6 fine sand). |
| 31 | 12 mm thick cement plaster 1:3 (1 cement : 3 fine sand)finished with a floating coat of neat cement. |
| 32 | 6 mm thick cement plaster 1:3 ( 1 cement : 3 fine sand). |
| 33 | Repair of plaster in patches of area 2.5 sq.m. and underm including cutting the patch in proper shape preparing and plastering the surfaces complete including disposal of rubbish to dumping yard with cement mortar 1:4 (1 cement : 4 fine sand). |
| 34 | Providing and laying white glazed/Vetrified tiles of min. thickness 5 mm on skirting, sides of steps, dados on 12 mm thick cement laster 1:3 (1 cement : 3 fine sand) and jointed with white cement slurry. |
| 35 | Providing and laying 25 mm thick kota stone in floor or in skirting over 20 mm thick cemenr sand morter (1 cement :4 coarse sand) including grinding polishing etc complete. |
| 36 | Only fixing of single layer monolithic cement concrete blocks in true line and level on ground level,as per directions of Engineer-in-Charge. Pavement bocks shall be supplied by NFL free of cost at its stores. |
| 37 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position: a) Second class Teak wood |
| 38 | b) Sal wood/or equivalent as approved by Engineer-in-Charge |
| 39 | Providing and fixing flush door shutters, decorative type, core of block board construction with frame of 1st class hard wood and well matched 1st class teak 3 mm ply veneering with vertical grains or cross bands and face veneers on both face of shutters : |
| 40 | a) 35mm thick including anodised MS butt hinges with necessary screws. |
| 41 | Providing and fixing glazed/wire gauge shutters for doors, windows,clerestory windows using 7.5 kg/sq.m. ( 3 mm thick) glasspanes/wire gauge including black enamelled M.S. butt hinges withnecessary screws: a) Second class teak wood 35 mm thick |
| 42 | Providing and fixing 12 mm thick, 150 mm wide pelmet of 19 mm block board and 12mm thick commercial ply on top with 20mm dia. M.S. conduit pipe, curtain rod including fixingwith 25x3 mm M.S. flat 10 cm long and plugs etc. complete. |
| 43 | Providing and fixing M.S. conduit curtain rods 20 mm dia. |
| 44 | Providing and fixing/replacing M.S. fittings of doors windows with necessary screws (bright finished or black enamelled) : |
| 45 | a) M.S. sliding door bolt 16 mm dia. x 300 mm long |
| 46 | b) M.S. tower bolt barrel type 150 x 10 mm |
| 47 | c) M.S. handle 100 mm /Hasp and staple 100 mm |
| 48 | d) M.S. casement stay 300 mm |
| 49 | e) M.S. window fastener 100 mm |
| 50 | f) M.S. butt hinges 100 mm x 58 x1.90 mm |
| 51 | Providing and fixing/replacing M.S. fittings of doors windows with necessary screws (bright finished or black enamelled) : |
| 52 | a) Sliding door bolt 16 mm dia. 300 mm long |
| 53 | b) Tower bolt 150 x 10 mm |
| 54 | c) Handle 100 mm/Hasp and staple 100 mm |
| 55 | Renewing old putty of glass panes (length) |
| 56 | Providing and fixing plywood plain lining with necessary screws/nails (no deductions for opening upto 0.25 Sq.M. shall be made) complete with : |
| 57 | a) Teak ply of approved brand (4 mm thick) |
| 58 | b) Commercial ply of approved brand (6 mm thick) |
| 59 | c) Commercial ply of approved brand : i) 12 mm thick water proof ply |
| 60 | Providing and fixing/replacing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 61 | Providing and fixing/replacing aluminium hanging floor door stopper anodised transparent or dyed to required colour & shade with necessary screws etc. complete. |
| 62 | a ) Providing and fixing/replacing bright finished hydraulic door closer (best make of approved quality) with necessary accessories & screws etc. complete : Right/Left/Universal type |
| 63 | Providing and fixing/replacing wooden cleats of size 100 x 75 x 50 mm to doors and windows with approved fittings including removal of old cleats where necessary includingpainting, polishing or bees waxing to match the existing shade: Ist class kail wood cleats with iron hinges and screws. |
| 64 | Proving and fixing/replacing heat resistant sun control film one side silvered and the other side transparent for fixing on window panes as per site requirement at all heights,including cleaning of surfaces complete. Imperfections like bubbling, crip, joints etc. in film fixed in one pane shall not be allowed as per directions of Engineer-in-Charge. Before start of worka sample shall be got approved. The film shall be of non-reflective range of GARWARE or equivalent quality. |
| 65 | Providing and fixing sunmica of approved quality with proper adhesive (fevicol etc.) including making surface wherever required. |
| 66 | Providing and fixing 19 mm thick block board non decorative type with core of 1st class hard wood and well matched commercial ply veneering with vertical grains or cross bands and face veneers on both faces. |
| 67 | Providing and fixing galvenised MS wire gauge of average width of aperture 1.18 mm with wire of dia. 0.56 mm in doors,windows or at any other place including necessary nails, screws etc. complete. |
| 68 | Supplying and applying antitermite solution on the existing wood work i.e. door frames,wall panelling,door shuterrs etc. |
| 69 | Providing and fixing Asbestos cement 6 mm thick sheet roofing at any height and fixing with GI - J or L hooks, bolts and nuts 6/8 mm dia., G.I. plain & bitumen washers complete excluding the cost of purlins, rafters and trusses, at any pitch. |
| 70 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required |
| 71 | Dismantling of A.C./GI sheet roofing at any height including removal of ridges,hips,valleys and gutters etc., and stacking the material within 50 metres lead and disposal of unserviceable material in dump yard within plant area. |
| 72 | Rectification of AC/GI sheet roofing at any height by replacing damaged bitumen/GI washers and tightening the existing bolts, nuts & sealing all the holes with tarplastic compound to give full water proofing to the roof including all labour, tools tackles etc.and fixing of scaffolding wherever required at all heights (All ther materials required for the work shall be given free by NFL). |
| 73 | Fixing of AC sheets 6 mm thick/translucent sheets/GI Sheet in roofing/wall cladding at any height by providing and fixing G.I. - 'J' or 'L' hooks and nuts 6/8 mm dia. including plain andbitumen washers complete (only A.C. sheets/transluscent sheet/GI sheets will be supplied by NFL free of cost). |
| 74 | Supplying and applying Tarplastic Water proof putty ofapproved brand and manufacture, wherever required as per directions of Engineer-in-Charge. |
| 75 | Providing non asbestos high impact Polypropylene reinforced cement 6 mm thick corrugated sheets roofing upto any pitch and fixing with polymer coated J or L hooks bolts and nuts 6/8 mm dia. G.I. plain and Bitumen washers or with self drilling fasteners and EPDM washers etc. complete including cutting to size and shape wherever required. |
| 76 | Providing and fixing on wall face unplastcized Rigid PVC pipes conforming to IS 13592 Type A including jointing with seal ring leaving 10 mm gap for thermal expansion Single socketed pipes. (i) 75 mm diameter |
| 77 | (ii) 110 mm diameter |
| 78 | Providing and fixing on wall face unplastcized PVC moulded Fittings/acessories for unplastisized PVC rain water pipes conforming to 13592 Type A including jointing with seal ringleaving 10 mm gap for thermal expansion :-Coupler /Bend/Shoe i) 75 - 110 mm |
| 79 | Providing and fixing/replacing white vitreous china water closet squatting pan (Indian type) Orissa pattern W.C. pan size 580x440 mm. |
| 80 | Providing and fixing/replacing white vitreous china pedestal type (European type/wash down type) water closet pan. |
| 81 | Providing and fixing/replacing 7.5 ltrs. low level P.V.C.flushing cistern with fittings complete. |
| 82 | Proving and fixing/replacing white vitreous china wash basin including making all connections but excluding the cost of fittings : flat back wash basin of size 630 x 450 mm. |
| 83 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 84 | Providing and fixing/ replacing C.P. brass waste for sink or wash basin : a) 32 mm-40 mm dia |
| 85 | Providing and fixing/replacing 32 mm dia G.I. flush pipe complete including cutting and making good the walls and floors wherever required. |
| 86 | Providing and fixing/replacing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick asbestos cement sheet ground fixed to wooden cleats with screws and washers. |
| 87 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling dismantling of wall and making good the same wherever required (internal/external work): |
| 88 | a) 15 mm nominal bore |
| 89 | b) 20 mm nominal bore |
| 90 | c) 25 mm nominal bore |
| 91 | d) 40 mm nominal bore |
| 92 | Dismantling G.I. pipes (external/internal work) including excavation and refilling trenches after taking out the pipes, including stacking of pipes within 50 mtrs. lead: a) 15 to 40 mm & Above nominal bore |
| 93 | Only laying G.I. pipe complete with G.I. fittings ( only pipe shall be supplied at NFL stores free of cost) : a) 15 mm to 25 mm |
| 94 | do- d) 40 mm to 150 mm |
| 95 | Providing and fixing brass ferrule C.I. mouth cover including boring and tapping the main: 20 mm nominal bore. |
| 96 | Providing and fixing/replacing plastic seat with lid for pedestal type W.C. pan with C.P. brass hinges, rubber buffers etc., complete: a) Black/White plastic seat with lid |
| 97 | Providing and fixing/replacing unplasticised PVC connection pipe with unions : 15 x 300 mm |
| 98 | Providing & fixing/replacing internal fittings complete set for : a) Low level flushing cistern including handle |
| 99 | Providing and fixing/replacing plastic floats for desert cooler / high level flushing cisterns , O.H.Tanks: a) For 15/20 mm |
| 100 | Providing and fixing/replacing G.I. fittings to G.I. pipe line i.e. Socket, elbow, Tee, plug, union, nipple etc. including necessary excavation-refilling/dismantling wall and makinggood the same wherever required : a) 15 -25 mm |
| 101 | do- -b) 40- 50 mm |
| 102 | Providing and fixing/replacing brass stop cock/ Bib cock of approved quality : a) 15 mm - 20 mmnominal bore |
| 103 | Providing and fixing/replacing C.I. push cock/lift cock/bib cock of approved quality : 15 mm nominal bore. |
| 104 | Providing and fixing/replacing ball valve (brass) of approved quality complete : a) 15 mm to 20 mm nominal bore |
| 105 | Providing and fixing/replacing C.P. pillar cock/bib cock of approved quality / make : a) 15 mm |
| 106 | do -b) 15 mm swan neck pillar cock for laboratory sink |
| 107 | Providing and fixing/replacing brass full way valve with C.I. wheel of approved quality (screwed end) : a) 15 mm- 25 mm |
| 108 | - Do-b) 40 mm - 50 mm |
| 109 | -Do ---c) 80 mm |
| 110 | Erection of safety showers including making all connections and commissioning the same(safety showers & fittings shall be supplied free of charge by NFL). |
| 111 | Providing and fixing 100 mm CP mild steel sheet grating for gully, floor and Nahani trap. |
| 112 | Repair/maintenance of water supply and sanitary fittings/fixtures including providing and fixing washers, jumper valves etc. wherever required for keeping the same in smooth operation without any leakage : a) High level/low level flashing cisterns of W.C./Urinalsb) Bib cock/stop cock/Pillar cock/Push cock/Lift cock and Ball Cock etc. of any size. c) Ball valve/Full way wheel valve any size ( d) Safety Showers |
| 113 | Providing and fixing PTMT (An Engineering thermoplastic) urinal spreader of approved quality, colour and make (prefereably PRAYAG INDIA SYMET) 15mm with size 95x60x100mm with 15mm BSP threads and shape as per BIS specifications and approx. weight of 60 gms. |
| 114 | Providing and fixing/replacing internal PVC fitting for low level flushing cistern including side inlet valve lever type, out flow valve, front lifting arrangement and acessories for LLC adaptor & overflow pipe plus ball ISI mark- Superflow make : a) Single/Double syphonic system. |
| 115 | Providing and fixing/replacing white vitreious chinal flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x256 mm size respectively with automatic flushing cistern with CI /MS brackets standard flush pipe and CP brass spreader with brass unions and GI clamps complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required. a) 1 Urinal basin with 5 Ltr. PVC automatic flushing cistern. |
| 116 | DO----b) Range of two urinals basin with 7.5 Ltr. PVC automatic flushing cistern. |
| 117 | Providing and fixing stainless steel sink without drainage board of approved quality and standard size including CP waste, fixing the same on brackets etc. complete :size - 460 x 915 mm, bowl depth 178 mm. |
| 118 | Providing and fixing stainless steel sink with drainage board of approved quality and standard size including CP waste, bowl depth 178 mm.fixing the same on brackets etc. complete : size 460 x 915 mm |
| 119 | Demolishing plain cement concrete work including disposal of material within 50 mtrs. lead. |
| 120 | Demolishing RCC work including stacking of steel bars and disposal of unserviceable material within 50 mtrs. lead. |
| 121 | Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 mtrs. lead in cement mortar. |
| 122 | Demolishing stone rubble masanory including stacking of serviceable material and disposal of unserviceable material within 50 mtrs. lead in cement mortar. |
| 123 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for new plaster including disposal of rubbish to the dumping ground within 50 mtrs. lead. |
| 124 | Renewing glass panes, with putty and nails or wooden fillets wherever necessary : a) Upto 3 mm- 4 mm |
| 125 | DO--d) Wired glass 5.5 mm |
| 126 | Repair/rectification/adjusting and maintenance of existing doors, windows, ventilators and their fittings including providing and fixing necessary screws/nails etc. for smooth functioning of these fittings : a) Doors including locking bolts/tower bolt/handles/hinges b) Windows including locking bolts/tower bolt/handles/hinges c) Pelmets / curtain rods d) Hydraulic door closer including Oiling & Greasing |
| 127 | DO-- e) Fixing/removing and re-erecting name plates/displayboards/ Notice boards on walls/door shutters |
| 128 | f) Mortise lock repair/providing & fixing handles |
| 129 | Cleaning of water tanks including removal of sludge, algae etc. ,washing, dis-infecting and again washing including removal & re-fixing of covers of overhead tank complete. |
| 130 | Inspection and making small repairs/rectifications of foundations, bolts of pumps, heavy equipments, floors etc. against vibration and other related minor maint. works ofwalls, floors, drains, outlet/inlet pipes, manholes, struc- tures, pedestals, tank foundations etc., and small seepages repair in toilet, roof and railing repairs, any other masonary related job. |
| 131 | Removal of chockage of following sanitary installations for smooth functioning: a) Floor trap/gully trap, water closet(European/Indian) wash basins, rain water pipes etc. |
| 132 | DO --b) Sewer lines from Manhole to Manhole |
| 133 | Cleaning of storm water drains in plant areas (with size measured at bottom of drain) including uprooting of rank vegetation, removal of small debries etc., and disposal of the same in dump yard/anywhere within plant area : |
| 134 | a) Small drain upto 0.5 Mtr. Width |
| 135 | b) Drain upto 1 Mtr. Width |
| 136 | c) Drain more than 1 Mtr. width including final outlets upto boundary wall irrespective of the width of the drain |
| 137 | Sweeping of roof tops, against chocking of drain out pipes, roads, road junctions/turnings against slippage and other floor areas including collection of loose materials anddumping the same in dump yard within plant area. |
| 138 | Erecting/fixing in true line/level and plumb doors, windows, ventilators of steel or wood including chokhats upto 2.5 Sq. M. area including cartage of doors, windows, ventilators from stores to site of erection within NFL Estate. |
| 139 | Providing and laying marble stone flooring with 20 mm thick marble stone over 20 mm average thick base and jointed with cement slurry including providing and mixing pigmentsincluding rubbing and granite polishing complete in cement mortar 1:4 ( 1 cement : 4 coarse sand) ; a) Bundi grey marble / Adanga Pink marble. |
| 140 | Providing and fixing mat finish good quality ceramic tiles of any size,pattern and colour of minimum thickness 8 mm on vertical/horizontal surfaces on a bed of 12 mm thick cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with grouting / pointing in white cement mixed with pigment to match the colour of the tile. |
| 141 | Providing and fixing square mouth SW gully trap grade Acomplete with CI grating, brick masonry chamber with bricks of class designation 50 and water tight CI cover with frame of 300x300 mm size (inside), the weight of cover should not be less than 4.5 Kg. and frame should not be less than 2.7 Kg. as per standard design, 100x100mm P Type. |
| 142 | Providing and fixing Fire Retardant Transluscent sheets in any shade (fixing to match with asbestos cement corrugated sheets) of approved make, made of polyster fibre-glass reinforced 1.2mm thick fixed in roofing and or wall cladding with necessary fixtures e.g. galvanised bolts, nuts, hooks etc. all complete as directed by Engineer in charge (wt. of sheet shall not be 6 ounce per sq.ft.). |
| 143 | Cleaning of road berms, islands. divider strips or any other area and fine dressing the surface including cutting of grass/wild growth with spade/scratching the area including collection of fallen leaves/branches of trees/bushes and any other foreign material, and removingof cut grass / loose materials from site of work to dumping yard anywhere in NFL estate in connection with VIP visit. |
| 144 | Supplying and fixing of 40 mm thick rough chisel dressed Red Sand Stone flooring over 20 mm thick base with cement mortar 1 : 5 (1 Cement : 5 Coarse Sand) or Providing and fixing Red Stone Slabs on Top of drains as drain covers by joining the slabs with top of the drain wall with cement mortar 1 : 5 (1 Cement : 5 Coarse Sand) complete. ( Pointing of the joints of Red Sand Stone if required shall be paid separately ). |
| 145 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to matchthe shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).i. Light shade pigment using white cement |
| 146 | Cutting of Holes (CORE CUTTING) through Vibration less Core cutting method from the RCC roof slab /floor slab /walls of thickness upto 300 mm core diameter up to 200mm as per Directions of Engineer in Charge.All necessary cutting tools shall be under the scope of contractor. |
| 147 | Engaging Back Hoe Loader 3D excavator (JCB,CAT etc.) including driver, necessary tools,including fuel charges on the basis of per day ( 8 hrs.) working for miscellaneous works i.e. excavation,dressing,dismanteling, lifting etc.as per directions of Engineer-In-Charge. |
| 148 | Engaging Air compressor/concrete breaker(Tractor/JCB Mounted) 250 cfm including driver, necessary tools,including fuel charges on the basis of per day ( 8 hrs.) with two leads for pneumatic cutters / hammers for miscellaneous demolishing/dismantling jobs as per directions of Engineer-In-Charge. |
| 149 | PART B Please Enable Macros to View BoQ information |
| 150 | PART B Please Enable Macros to View BoQ information |
