|
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 2 | Demolishing brick work, manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.All kinds of soil. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 3 | Dismantling old plaster or skirting/Dado raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 4 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer in charge. 1:3:6 or richer mix Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 5 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 6 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles 10 mm to 25 mm |
| 7 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of G.S. Sheet |
| 8 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 9 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead. Of area 3 sq. metres and below.Including supply of all material, labour, T&P etc required for proper completion of the work |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:3:6 (1 Cement :3 coarse sand : 6 graded stone aggregate 40 mm nominal size). Including supply of all material, labour, T&P etc required for proper completion of the work |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - in kerbs, steps and the like at or near ground level. 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 12 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 14 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand). Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in in Cement mortar 1:6 (1 cement : 6 coarse sand). Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 17 | Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement :4 coarse sand)Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 18 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 19 | Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level,including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at window sills, ceiling level and the like with Cement mortar 1:6 (1 cement : 6 coarse sand)Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 20 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position. Sal wood.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 21 | Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc 300x16mm .Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 22 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc.150x10 mm .Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 23 | Providing and fixing ISI marked oxidised M.S.handles conforming to IS:4992 with necessary screws etc. 100 mm . Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 24 | Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. 100x58x1.90 mm . Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 25 | Providing and fixing ISI marked M.S. pressed butt hinges bright finished 50x37x1.50 mmIncluding supply of all material, labour, T&P etc required for proper completion of the work. |
| 26 | Providing and fixing ISI marked oxidised M.S. single acting spring hinges 150mmIncluding supply of all material, labour, T&P etc required for proper completion of the work. |
| 27 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised. Twin rubber stopper. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 28 | Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory. With 2nd class teak wood beading 62X19 mm.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 29 | Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory. With 12 mm mild steel U beading.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 30 | Renewing glass panes, with putty and nails wherever necessary Float glass panes of thickness 4 mm.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 31 | Refixing old glass panes with putty and nails.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 32 | Renewal of old putty of glass panes(length) Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 33 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.C.C. Work Using Mild Steel and Medium /Tensile Steel Bars. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 34 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 35 | Providing and fixing G.I. chain link fabric fencing 25x25mm made of G.I. wire of dia 3 mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4mm.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 36 | Providing and fixing curtain rods of 1.25 mm thick 25 mm dia.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 37 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less than sq.m 275gm/m |
| 38 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m² |
| 39 | Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 40 | Micro Alloyed Cement concrete(M-40 and above grade)work for Repair Work Stair's and old structure,Including labour T&P etc. for proper completion of work.Including supply of all material,labour, T&P etc. Required for proper completion of work. |
| 41 | 12 mm cement plaster of mix 1:6 (1 cement : 6 coarse sand). Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 42 | 12 mm cement plaster of mix 1:4 (1 cement : 4 coarse sand) . Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 43 | Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. 18 mm thick. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 44 | Providing and fixing glass strips in joints of metre terrazo/ cement concrete floors. 40 mm wide and 4 mm thick. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 45 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 46 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 47 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour OTwo coats.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 48 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour One coa.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 49 | Lettering with black Japan paint of approved brand and manufacture.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 50 | Re-lettering with black Japan paint of approved brand and manufacture. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 51 | Hire charges of welding machine with single phase with welder, helper and electrodes etc. for repair and welding of gates, door, window etc. for 8 hrs. in a day complete with all material labour, T&P etc. required for proper completion of work.(As per previous approved Argreement/copy attached) |
| 52 | Supply Beldar/mazdoor/mali (unskilled) for full day as per requirement for attending miscellaneous works as per direction of the enginner in charge for proper completion of the work in emergency withT&P as required. |
| 53 | Attending minor type of repair for full day by engaging and supplying one suitable Beldar/mazdoor for carrying simple type of repairing of all work including all T&P etc. complete but excluding cost of material.(As per approved analysis) |
| 54 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 55 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I)non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 56 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1stquality conforming to IS :15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 57 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete Size of Tile 60x60 cm. Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 58 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 59 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 60 | Finishing walls with Acrylic Smooth exterior paint of required shade Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 61 | Engaging & operation of one tractor along with one driver & trolley having hydrulic jack arrangement,including cost of fule lubricants and repair maintenance etc.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 62 | Providing and fixing soil, waste and vent pipes: 100mm dia.Sand cast iron S&S pipe as per IS: 1729.(As perIncluding supply of all material, labour, T&P etc required for proper completion of the work. |
| 63 | Providing and fixing soil, waste and vent pipes: 75mm dia.Sand cast iron S&S pipe as per IS: 1729.(As per Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 64 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983. Kitchen sink without drain board, 470x420 mm bowl depth 178 mm.(As per Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 65 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.(Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 66 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :3 mm thick including supply of all material labour T&P etc, also including treatment to expansion/construction joints.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 67 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed.1 Earth work in excavation in all kinds of soils. (Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 68 | Cleaning grass, and removel of the rubbish upto a distance of 50 m outside the peripherery of the area clearedIncluding supply of all material, labour, T&P etc required for proper completion of the work. |
| 69 | Providing and fixing aluminium work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).Anodised aluminium (anodised transparent or dyed to required shade according kilogram to IS: 1868, Minimum anodic coating of grade AC 15) Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 70 | Providing and fixing glazing in aluminium door, window, ventilator shutters and With float glass panes of 4.0 mm thicknessIncluding supply of all material, labour, T&P etc required for proper completion of the work. |
| 71 | Providing and fixing double action hydraulic floor spring of approved brand and With stainless steel cover plateIncluding supply of all material, labour, T&P etc required for proper completion of the work. |
| 72 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. Including Supply of all material labour, T&P etc required for proper completion of the work |
| 73 | Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick Anodized (AC 15 ) aluminium tubular handle bar Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 74 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.(Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 75 | With float glass panes of 5.50 mm thickness.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 76 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc.Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 77 | Providing and fixing aluminium work for doors, windows, ventilators and partitions For fixed portion.Anodised aluminium (anodised transparent or dyed to required shade according kilogram to IS: 1868, Minimum anodic coating of grade AC 15)Including supply of all material, labour, T&P etc required for proper completion of the work. |
| 78 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work |
| 79 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work |
| 80 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover |
| 81 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1 : 4 (1cement : 4 coarse sand) 25 mm thick |
| 82 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average)thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge |
| 83 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts,bolts, fasteners etc.). |
| 84 | Engaging & operation of one no.Hydraulic excavator cum loader machine (preferably JCB)having capacity 75 BHP with one operator an one helper, including cost of fule lubricants and repair maintenance etc. for removal of slip/landslide/excavation in dry and wet condition, complete in all respect as per direction of I/C. |
| 85 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 86 | Relaying pitching on slopes laid over prepared filter media as per drawing and technical specifcation Clause 1302 Stone/Boulder(excluding cost of stone). |
| 87 | Eproxy bonding of new concrete to old concrete including all cost of material,labor, and T&P etc required for proper completion of worK |
| 88 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 89 | Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete |
| 90 | Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 ≥45 MPa and adhesive bond strength Class R3 ≥1.5 MPa. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage For sealing cracks and faulty construction joints, routed out/making U-shape groove size 25x25mm and then primed the area with integral crystalline slurry @0.05kg/running metre and while the surface is tacky filled the groove upto surface with crystalline mortar @1.50kg/running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05kg/running metre per coat. |
| 91 | Applying of rapid setting intergel crystalline cementitous PENPLUG or equivalent for treatment of seapage/ leakage.Including supply of all material,labour and T&P etc required for proper completion of work required. |
| 92 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and water jet pressure etc. and disposal of debris. 50mm average thickness.Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge. |
| 93 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 94 | Supply & Instalation of VISTA classic or equivalent vertical blinds of diiferent colour as approved Including supply of all material,labour and T&P etc required for proper completion of work. |
| 95 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 96 | Centering and shuttering including strutting, propping etc. and removal of Suspended floors, roofs, landings, balconies and access platform |
| 97 | Providing and fixing of 40 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts, G.l. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1 cement : 3 coarse sand). 1.00 mm thick with zinc coating not less than 275 gm/m² |
| 98 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete |
| 99 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required |
| 100 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on walls PN - 16 Pipe, 20mm OD (SDR-7.4) |
| 101 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on wallsPN - 16 Pipe, 25mm OD (SDR-7.4) |
| 102 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on walls PN - 10 Pipe, 50 mm OD (SDR-11) |
| 103 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work PN - 16 Pipe, 20mm OD (SDR-7.4) |
| 104 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work PN - 16 Pipe, 25mm OD (SDR-7.4) |
| 105 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work PN - 10 Pipe, 50 mm OD (SDR-11) |
| 106 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work PN - 10 Pipe, 75 mm OD (SDR-11) |
| 107 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work PN - 10 Pipe, 110mm OD (SDR-11) |
| 108 | Providing and fixing PPR Unions Including supply of all material, labour, T&P etc required for proper completion of the work. PPR Union 20mm |
| 109 | Providing and fixing PPR Unions Including supply of all material, labour, T&P etc required for proper completion of the work. PPR Union 25mm |
| 110 | Providing and fixing PPR Unions Including supply of all material, labour, T&P etc required for proper completion of the work. PPR Union50 mm |
| 111 | Providing and fixing PPR Unions Including supply of all material, labour, T&P etc required for proper completion of the work. PPR Union75 mm |
| 112 | Supplying and fixing Bib cock with Flange Jagaur make model KUP-35037M or equivalent including T&P etc. require for proper completion of work |
| 113 | Supplying and fixing Wash basin Full Pedsatal with fixing accessaries set,size 620X480X185 mm of Jagaur make model FNS-WHT-40801 or equivalent including T&P,labour etc. require for proper completion of work |
| 114 | Supplying and fixing Single Piece -WC with PP soft close slim seat cover,Hinges,Fixing accessaries set,size 360X640X685mm of Jagaur make model SLS-WHT-6851P180PP or equivalent including T&P,labour etc. require for proper completion of work. |
| 115 | Supplying and fixing Urinal basin ,Fixing accessaries set,size 355X340X535mm of Jagaur make model SLS-WHT-6851P180PP or equivalent including T&P,labour etc. require for proper completion of work. |
| 116 | Supplying and fixing Pillar cock with Flange Jagaur make model KUP-35011 or equivalent including T&P etc. require for proper completion of work. |
| 117 | Supplying and fixing Angular Stop cock with Flange Jagaur make model CQT-23053 or equivalent including T&P etc. require for proper completion of work |
| 118 | Supplying and fixing Connection Pipe with Flange Jagaur make model ALD-803AB or equivalent including T&P etc. require for proper completion of work |
| 119 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 120 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds Using R4 series with frame (64 mm & above) x (45 mm & above) & sash (44 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height above 1.8m) |
| 121 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system, adjustable nylon rollers with SS 304 body Using R4 series with frame (64 mm & above) x (45 mm & above) & sash (44 mm & above) x (85 mm & above). (Height above 2.5 metre) |
| 122 | Sealing of cracks/porous concrete by injection process through nipples/Grouting complete as per Technical specification. |
| 123 | Removal of defective concrete, cleaning the surface thoroughly, applying the shotcrete mixture mechanically with compressed air under pressure, comprising of cement, sand, coarse aggregates, water and quick setting compound in the proportion as per clause 2807.1., sand and coarse aggregates conforming to IS: 383 and table 1 of IS: 9012 respectively, water cement ratio ranging from 0.35 to 0.50, density of gunite not less than 2000 kg/cum, strength not less than 25 Mpa and workmanship conforming to clause 2807.6. |
| 124 | Providing and inserting nipples with approved fixing compound after drilling holes for grouting as per Technical specifications including subsequent cutting/removal and sealing of the hole as necessary of nipples after completion of grouting with Cement/Epoxy |
| 125 | Providing & Injecting the existing holes with two componenets fast reacting hydrophilie foam water reacting flexible foam sika injection101H or equivalent.Including of all material,Labour,T&P etc require for proper completion of the work. |
| 126 | Providing and applying injection with two component hydrophobic polyurethane resin sika 201CE or equivalent having specific gravity 1.05 and viscosity of 100 mm Mpa complete as per direction of Engineer in charge.Including of all material,Labour,T&P etc require for proper completion of the work. |
| 127 | Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 128 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 129 | Painting with aluminium paint of approved brand and manufacture to give an even shade One or more coats on New work |
| 130 | Painting with aluminium paint of approved brand and manufacture to give an even shade One or more coats on old work |
| 131 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 Sqm Including Supply of all material labour, T&P etc required for proper completion of the work |
| 132 | Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.63 mm thick with zinc coating not less than 275 gm/m² |
| 133 | Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504.Including supply of all material, labour, T&P etc required for proper completion of the work. Please Enable Macros to View BoQ information |
