|
| 1 | Demolition of concrete of any description and in any position above or below ground level and disposing off debris outside MD land, etc., complete all as specified and directed. |
| 2 | Demolition of brick work or stone masonary built in cement mortar including quoins, arches, pillars, etc., and precast concrete articles and deposing off the debris outside MD land, complete all as specified and directed. |
| 3 | Material and labour for plain cement concrete type D2 (1:4:8) using 40mm graded stone aggregate as in sub base, filling and mass concrete, etc., complete all as specified and directed by Engineer-in-Charge. |
| 4 | Material and labour for plain cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate as in top layers for hard standing, pavings, etc., finished with even and fair surfaces, without using extra cement, etc., complete all as specified and directed. |
| 5 | Material and labour for chequered cement concrete tiles (with grey cement and pigment) manufactured in rubber moulded finish of size not less than 300x300 of thickness 22 to 25mm, set, jointed and pointed in neat cement slurry over and including 20 mm thick cement mortar screed bed in cement mortar (1:6) as in floors including dismantling of old tiles complete all as specified and as directed. |
| 6 | Material and labour for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness, shape and size made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including dismantling of old paver block complete all as specified and as and directed by Engineer -in- Charge. |
| 7 | Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including dismantling of old kerb stone and removing debris to a distance exceeding 1.5 KM but not exceeding 5.0 KM from the site, etc., complete all as specified and as directed. |
| 8 | Material and labour for preparation of new concrete or cemented surfaces and applying two coats of plastic emulsion paint over a coat cement primer, etc., all as specified and as directed. |
| 9 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons, riser of steps, skirting, dado etc laid in any mortar complete all as specified. |
| 10 | Material and labour 18 to 20mm thick granite stone (of any type) work (table rubbed and polished) in floors, staircase treads and risers of steps, cooking platform, window sill/ jambs or in vertical surfaces, etc., laid using 15mm thick cement mortar (1:4) and pointed in white/coloured cement to match coloured tiles including rounding, grinding and mirror polishing complete all as specified and directed. NOTE:- Colour of granite shall be as approved by Engineer-In-Charge |
| 11 | Material and labour in repairs to stainless steel (Grade 304) railing made of hollow tubes, channels, plates, chains etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and including taking down existing railing of any descriptions etc all as specified and as directed. |
| 12 | Supplying and fixing signage board made of 4 mm thick Aluminium Composite Panel sheet fixed on stailness steel (Grade 304) frame including reflective vinyl printing and letter writing, cutting, fixing with stailness steel screws, including taking down old sheets, complete all as specified and directed by Engineer-in-Charge. |
| 13 | Material and labour for precast cement concrete solid block masonry with solid blocks using plain cement concrete, type C1 (1:3:6), (using 20mm graded stone aggregate), exceeding 10cm in width, set in cement mortar (1:6), etc., all as specified and directed. |
| 14 | Material and labour for walling of squared rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:4) complete all as specified and as directed. |
| 15 | Taking down cement plaster on brick/ stone masonry/ concrete surfaces of wall/ ceiling including raking out joints, hacking for key, scrubbing down with water, etc., and deposing off the debris outside MD land, complete all as specified and directed. |
| 16 | Material and labour for rendering 15mm thick in cement plaster (1:4) on fair faces of brick work or concrete surfaces, to be finished even and smooth without extra cement, etc., complete all as specified and as directed. |
| 17 | Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement based paint of approved tint over a coat of primer, complete all as specified and as directed. |
| 18 | Material and labour for flush pointing to squared rubble masonry coursed or uncoursed in cement mortar (1:3) complete all as specified and as directed |
| 19 | Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for, reinforcement cut through to facilitate demolition and deposing off the debris outside MD land as specified and directed. |
| 20 | Material and labour for precast reinforced cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in manholes/ drain covers, slabs, etc., set in cement mortar (1:4) including necessary form work, etc., complete all as specified and directed. |
| 21 | Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, culverts and similar work, flat and rough finished surfaces not exceeding 200mm thick (horizontal or sloping) etc., all as specfied and as directed. |
| 22 | Material and labour for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed |
| 23 | Material and labour for providing plain cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate as in kerbs of mud stops, borders, copings, etc,. rounded or chamfered on edges, all as specified and as directed. |
| 24 | Material and labour for plain cement concrete type B2 (1:2:4) using 40 mm graded stone aggregate as in surface channels and drains etc., complete all as specified and directed. |
| 25 | Extra for forming fair finished drain or channel 30 to 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc completed all as specified and directed. |
| 26 | Dismantling wrought iron or mild steel work of any description and in any position, etc., all as specified and as directed. |
| 27 | Supply and fix rolled mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde E-165, etc., all as specified and directed. |
| 28 | Material and labour for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint of approved tint over one coat of red oxide zinc chrome primer etc., all as specified and as directed. |
| 29 | Material and labour for preparation of old concrete or cemented surfaces and applying one coat of plastic emulsion paint of approved tint etc, all as specified and as directed. |
| 30 | Material and labour for preparation and cleaning of floor or concrete surfaces and applying one coat of terracotta paint, etc., complete all as specified and as directed. Please Enable Macros to View BoQ information |
