|
| 1 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed. |
| 2 | M & L for Providing, cement concrete 1:3:6 Type C1 using 20mm graded aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates etc as specified and directed. |
| 3 | M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length bent to shape required incl cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and as directed. |
| 4 | Demolition of Brickwork or stone/ boulder masonry, built in cement- mortar or lime-mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 5 | M&L for old size brick work with fly ash bricks straight or curved on plan to any radius half brick thick wall built in CM (1: 4). |
| 6 | M&L old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1: 6 complete all as specified. |
| 7 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar. |
| 8 | M&L for 16-18 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including hole for gas pipe in pre-cast slab as well as stone slab in cooking platform complete all as specified. |
| 9 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete. |
| 10 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. |
| 11 | M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding in cement mortar (1:6) complete all as specified and as directed. |
| 12 | M&L for Coloured Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and incl 10mm thick plaster in cement mortar (1:4) complete all as specified and directed. |
| 13 | Taking down cement plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified. |
| 14 | M&L for rendering 10mm thick in CM (1:6) on Brick/ Conc surface finished even and fair on internal surfaces of wall complete all as specified. |
| 15 | M&L for rendering 5 mm thick in CM 1:3 on concrete surface in ceiling complete all as specified. |
| 16 | M&L for preparation of new/old plastered surface and applying two coat of interior acrylic emulsion on walls over a coat of primer incl 1 mm thick wall care putty complete all as specified and directed. |
| 17 | M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth complete all as specified & as directed |
| 18 | Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe complete all as specified & as directed |
| 19 | Supplying and laying of CPVC pipes 16 mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 20 | Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20 mm bore pipe complete all as specified & as directed |
| 21 | Supplying and laying of CPVC pipes 20 mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 22 | S&F in repair 15 mm bore long body bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified & as directed |
| 23 | S&F in repair 15 mm bore angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified & as directed |
| 24 | S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & as directed |
| 25 | S&F in repair single lever sink mixer with table mounted with 235 mm long swivel spout and 450 mm long braided connection pipe fixed to iron pipe 15 mm bore complete all as specified and directed Make : cera Cat Part No. F1016551 or equivalent in make as specified and directed |
| 26 | S&F in repair Kitchen rack plate of stainless steel of size 75 x 60cm all as per sample kept with GE office |
| 27 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) Area not exc 1.5 Sqm each all as specified. |
| 28 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) Area exc 1.5 Sqm but n exc 4.00 Sqm each all as specified. |
| 29 | Dismantling boarding any desccription fixed in any position with nails or any other means complete all as specified and directed |
| 30 | S&F 105 x 60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and fixed |
| 31 | M&L for preparation of new steel primed surface and applying two coats of synthetic enamel paint over steel surface complete all as specified and directed. |
| 32 | M&L PCC (1:2:4) type B-1, using 20mm graded stone aggregate as in bed block and filling in door frames complete all as specified & as directed |
| 33 | S&F 30 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 34 | S&F 30mm thick plain WPC factory made glazed Skeleton door shutters (conforming as per IS-4020) with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door to be panelled with SS mosquito mesh and XTN aluminium mesh for additional strength and safety purpose. Door should be fixed with SS hinges and SS screws. Door should be water prrof, termite proof, fire retardant and having screw holding capacity complete all as per manufacturers specification & drawings & as directed by Engr-in-charge.Note- Stainless steel wire mesh shall be measured and paid separately. |
| 35 | S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples. |
| 36 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified & as directed |
| 37 | S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified & as directed |
| 38 | S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & as directed |
| 39 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & as directed |
| 40 | M&L for preparation of old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified. |
| 41 | M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified. |
| 42 | M&L for preparation of old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified. |
| 43 | S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. |
| 44 | M&L MS Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 45 | S&F Powder Coated aluminium frame for doors, windows, ventilators powder coated (thickness of powder coating not less than 50 micron) with one or more rebates including jointing cleat for fixing etc complete all as specified and directed. |
| 46 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note:-1. The rate is inclusive of all fixings of builders hardware such as hinges, bow handles, locking arrangements rubber beading for fixing of glass etc complete all as directed by Engr-in-Charge. 2. Glass and wiremesh shall be measured and paid separetely |
| 47 | M&L for 4.8 mm thick sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed. |
| 48 | M&L for 4.8 mm thick frosted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed. |
| 49 | S&F 140mm Floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring complete all as specified and directed. |
| 50 | S&F 300mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 51 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 52 | S&F Rolled MS Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) Fe 410 -W (Gde- E-250) quality A complete all as specified and directed. |
| 53 | Providing and fixing 18mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powcler/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being Termite/borer proof, water/moisture proof and Fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel hinges shall be paid separately) |
| 54 | Providing and fixing 12 mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for backing of cup boards and bathroom/kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In-Charge. |
| 55 | Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. |
| 56 | S&F magnetic catcher of size 20 mm X 50 mm suitable for cupboard shutter complete all as specified and directed. |
| 57 | Supply only 75 mm dia oval shape Stainless Steel handle fancy type polished bright finish complete all as specified and directed. |
| 58 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-charge. |
| 59 | Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in-charge (For payment purpose only weight of Stainless steel basket shall be considered including weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) complete all as specified and directed. |
| 60 | Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. |
| 61 | M&L wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, in modular electrogalvanised box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required One light point controlled by one way modular switch 6 Amps including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site & including chases cutting making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.Note :- Modular boxes and cover plate and accessories shall be measured and paid seperately |
| 62 | All as per item No 61 above but cable 2.5 sqmm FRLS for one 5 pin 5 Amp socket outlet point on an independent board. |
| 63 | All as per item No 61 above but cable 2.5 sqmm FRLS for one 5 pin 5 Amp socket outlet point on the same board with other switch. |
| 64 | All as per item No 61 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 4 sqmm. |
| 65 | Supply & fixing switch modular flush type 6 amps, single pole, one way complete all as specified and directed. |
| 66 | Supply & fixing socket modular flush type suitable for 6 amp, 2/3 pin combined 2 module complete all as specified and directed. |
| 67 | Supply & fixing switch modular flush type 16 amps, single pole, one way complete all as specified and directed. |
| 68 | Supply & fixing socket modular flush type suitable for 6/16 A, 2/3 pin combined 2 module complete all as specified and directed. |
| 69 | S & F Modular metal flush box 1/2 module complete all as specified and directed. |
| 70 | S & F Modular metal flush box 3 module complete all as specified and directed. |
| 71 | S & F Modular metal flush box 6 module complete all as specified and directed. |
| 72 | S & F modular metal flush box 8 modules (Horizontal) complete all as specified and directed. |
| 73 | S & F modular white cover plate 1 module complete all as specified and directed. |
| 74 | S & F modular white cover plate 2 module complete all as specified and directed. |
| 75 | S & F modular white cover plate 3 module complete all as specified and directed. |
| 76 | S & F modular white cover plate 6 module complete all as specified and directed. |
| 77 | S & F modular white cover plate 8 (Horizontal) modules complete all as specified and directed. |
| 78 | S&F lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 79 | S&F LED retrofit lamp of capacity 12 watt, B-22 holder base with polycabonate body and aluminium heat sink warm white complete including taking down old/ unserveciable CFL/bulb complete all as specified and directed. |
| 80 | S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed. |
| 81 | S& F LED tube light fittings of 18 wattage including rawl/plug ,making connection with and including 23/0 0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr fixed to wall firmly , complete all as specified and directed. |
| 82 | Taking down existing Exhaust fans including louver shutter and electrical connection and depositing to MES store and S&F of new exhaust fan heavy duty exhaust fan 300 mm sweep ,single phase 240 volt including making holes and electrical connection through wire of 3 core 23/0.0076 copper conductor marking MES No with paint complete all as specified and directed. |
| 83 | S&F of new wall fan heavy duty , single phase 240 volt including electrical connection through wire of 3 core 23/0.0076 copper conductor marking MES No. with paint complete all as specified and directed. |
| 84 | Supply, installation, commisioning and testing of wall mounted electric chimney, noise level not more than 58db, auto clean, motion senser control, operation mode exhaust type, size of chimney 600x500x140, push button control type 3 stage speed setting single phase 220 Volts AC, 150 watt 1200cum/Hr with energy saving LED lamp with baffle filter with all accessories required to install the elctric chimney including core cutting of walls for PVC hose pipe duly coveredwith aluminium cladding and making connection through wire of copper conductor complete all as specified and directed.Make :- Bosch/Faber/Elica/Hindware/Siemens Please Enable Macros to View BoQ information |
