|
| 1 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground wlthin 50 metres lead. (Cha.-17 S.I No. 21, SOR 2023-24) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge.All kinds of soil. ( Item No. 2.6.1 DSR-2023) |
| 3 | Extra lead up to 4 km. Cartage of Ballast, Kankar, Coal, Grit or Sand etc, including loading and unloadrng but excluding stackings on pucca roads (Ch.-3, Item No. 4 SOR-2023-24) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) . (SI.No-4.1.8 DSR 2023) |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) (SI.No-6.1.1, DSR 2023) |
| 6 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) (SI.No-13.4.1, DSR 2023) |
| 7 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). (SI.No-4.10, DSR 2023) |
| 8 | Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with mortar grader surface, mixing by mix in place method with rotavator at OMC, & compacting with vibratory power roller to achieve the desired density, complete as per clause Table - 400-2 S.N. 4.2 (C) MORT&H specification no- 401 grading size 53.00-26.50 mm @ 35 %, 26.50 - 4.75 mm @ 45 % and 2.36 mm & below @ 20 %. |
| 9 | Supply Laying of 80 mm I Shaped (Zigzag) rubber moulded gray precast Interlocking tiles of thickness 60 to 100mm (Compressive strength not less then 30Mpa and weight 4.50kg) Including 25mm thick local sand base levelling and dressing of surface to required level and slope, filling joints with local sand all complete work. (Cha.-20 S.I No. 17 E, SOR 2023-24 |
| 10 | Supply Laying of 60 mm I Shaped (Zigzag) rubber moulded Coloured Interlocking tiles of thickness 60 to 100mm (Compressive strength not less then 30Mpa and weight 4.50kg) Including 25mm thick local sand base levelling and dressing of surface to required level and slope, filling joints with local sand all complete work. (Cha.-20 S.I No. 17 E, SOR 2023-24 |
| 11 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (SI.No-10.25.2, DSR 2023) |
| 12 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) (SI.No-13.46.1, DSR 2023) |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work (SI.No-13.61.1, DSR 2023) |
| 14 | S/F of reinforced cement concrete bench complete with fixing as per directed by E/I as per given approved design and drawing all complete. (6'x4' size including fixing with cement concrete). Appd. Rate |
| 15 | Providing, & applying Priming Coat with bitumen emulsion(5581) on prepared surface of grangular base Including cleaning of road surface and spreading primer @ 0.70 kg/sqm. using mechanical means. Rates including of biturnen emulsion. (As per MORTH 502, MORT&H 2024 Rates taken from intergrated SOR dated on 1-11-2024 |
| 16 | Providing, & applying Tack coat with bitumen emulsion SS1 using emulsion pressure distributor @ 0.25 kg/sqm on the prepared grangular/ old painted surface, cleaned with mechanical broom Including all Taxes material, labour, T& P etc. required for proper completion of work. Rates including of (As per MORTH 503 MORT&H 2024 Rates taken from intergrated SOR dated on 1-11-2024) |
| 17 | Providing and laying Dense Graded Bituminous Macadam with higher capacity batch type HMP, using crushed stone aggregates of specified grading, premixed with Bituminous binder(VG-30) @4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density as per MORTH specification clause No. 505 (MORT&H 2024 Rates taken from intergrated SOR dated on 1-11-2024 |
| 18 | Providing and laying Bituminous concrete with higher capacity batch type hot mix plant using crushed stone aggregates of specified grading, premixed with Bituminous binder (VG-30) @5.4% by weight of total mix and filler, transporting the hot mix to work site, laying with paver finisher with sensor control to required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achleve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge, as per MORT & H specification clause no. 507. MORT&H 2024 Rates taken from Intergrated SOR dated on 1-11-2024) |
| 19 | Supply and fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body and lenses suitable for 75 watt to 90 Watt and Confirming to IP 66 Protection having company LOGO engraved complete in all respect including labour.CAT-AAA8250-9900 system lumens high power LED with lenses, > 110lm/W, PF>0.95, THD<10% at full load, CRI>70, potted driver set (Not circuitory), phase to phase protection at 440 V & > 300V auto cut and re-start feature, with 5 year warrantee. (S.I. No. 1423 / 2018) |
| 20 | Supply and laying of 10 sq. mm 4 core aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (S.I. No. 501(h) / 2018) |
| 21 | Supply and Wiring of submains with two nos. of 2.5 sq. mm. FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material labour and T & P required for proper completion of the work as directed at site by Engineer in charge. (SI. No. 289 / 2018) |
| 22 | Supply and fixing of 1 mtr. 40 mm. dia. G.I. pipe bracket with pole cap suitable for 9 mtr. S.T. pole all complete required for proper completion of work as per direction of E./Ic. (As per S.I. No. 641, 642 / 2018) |
| 23 | Supply & erection of \\"D\\" clamps of 50 mm x 6mm flat iron on steel tubular poles / steel rail poles with bolts, nuts etc. complete in all respects including painting with aluminium paint. (S.I. No. 623 / 2018). |
| 24 | Supply & fixing of 75 mm x 90 mm shackle insulator /100 mm x 65 mm pin insulator including G.I. Bolts / spindle nuts etc. complete in all respect. (S.I. No. 620 / 2018). |
| 25 | S&F of 100 Amp. 415 V metal clad TP HRC type switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. Cat. B. (S.I. No. 324 / 2018). Please Enable Macros to View BoQ information |
