|
| 1 | Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of entire debris as ordered outside MD land complete all as directed. |
| 2 | Demolition of cement concrete (unreinforced )in any description and in any position not otherwise specifically provided forcomplete all as specified and and removal of debris as ordered outside MD land complete all as directed. |
| 3 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed. |
| 4 | Demolition of brickwork , block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed. |
| 5 | Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed. |
| 6 | All as per item 5 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each |
| 7 | Taking down shutter of any description exc 1Sqm but not exc 2 Sqm each and stacking at site where directed. |
| 8 | All as per item 7 here-in-above but exceeding 1 Sqm but not exceeding 2 Sqm each -do- |
| 9 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 10 | Dismantling single layer mangalore pattern roof tiles including ridges laid and set in cement mortar complete all as directed. |
| 11 | Dismantling ceiling boarding of any description fixed in any position with nails incl cover fillets/aluminium snap grid. |
| 12 | Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed. |
| 13 | Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved. |
| 14 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in coping and on roof/benching over chajja etc complete all as specified and as directed. |
| 15 | M&L for Brick work with well burnt best quality locally available bricks, old size bricks, straight or curved on plan to any radius built in any description in cement mortar 1:6 complete all as directed |
| 16 | M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed. |
| 17 | Refixing shutters of any description in the same opening incl taking down and resecuring or easing and adjusting all as specififed not exc 1 sqm each |
| 18 | Refixing shutters of any description in the same opening incl taking down and resecuring or easing and adjusting all as specifife exc 1 sqm but not exc 2 sqm each |
| 19 | S&F Second class hard wood factory made kiln - seasoned, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixed in position complete all as directed. |
| 20 | S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed. |
| 21 | S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats. |
| 22 | S&F 40 mm thick Flush shutters, solid core construction, with block board core & plywood face panels both faces are covered with decorative face veneer conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fitted to chowkats all as specified |
| 23 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm width stuck inside with solvent cement for stiles and single sides prelam PVC sheet and stile & rails having one side feathered edge and on other side 10mm (90°) bent edges & as gap insert for top rail & bottom rail; Panelling to be fitted in the M.S. frame welded/ sealed to the styles & rail with suitable PVC sheet beading, and joint together with solvent cement, all as specification and drawing. |
| 24 | S&F 100 mm long Butt hinges, extruded aluminium ally with galvanished mild steel hinge pin anodised and fixed type B-21 |
| 25 | S&F mild steel butt hinges medium weight cold rolled 100 mm size |
| 26 | S&F mild steel butt hinges medium weight cold rolled 75 mm size |
| 27 | S & F 100 mm size aluminium anodised barrel tower bolt of extruded section . |
| 28 | S&F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) & fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. |
| 29 | S&F mild steel sliding door bolt plate type black jappaned with bright bolt not less than 12 mm dia with and including 6 bolts and nuts four o bolt plate and two on staple 250 mm long |
| 30 | S&F mild steel butt hinges heavy weight cold rolled 125mm size |
| 31 | S & F 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt. |
| 32 | S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised. |
| 33 | S & F in hasp and staple of size 125 mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hing plate and fixed with screws. |
| 34 | S&F powder coating anodised aluminium section for shutter/frame for door, window and ventilator complete all as specified. |
| 35 | S& F in repair stain less steel decorative curtain rod of 25 mm bore inluding 2 nos steel finale and bracket 02 nos etc and fixed to wall with plastic rowl plug and steel screw complete all as specified and directed. |
| 36 | S&F powder coating Anodised aluminium window and ventilator shutters, sliding type two or three tracks without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, aluminium fittings like locking system complete all as specified and directed by Engineer-in-Charge.(Thickness of powder coating not less than 50 micron) complete all as specified and as directed. |
| 37 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails complete all as directed. |
| 38 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails for wooden door/ window & for steel / aluminium widor/door with iron staples/aluminium bedding complete all as directed. |
| 39 | S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as completed |
| 40 | S & F rolled mild steel framed work as in doors or gates of angle or other section confirming to Fe 410 - W, with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete. |
| 41 | S&F Anodised aluminium snap grid frame work size 605x605 mm for false ceiling incl Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long all as specified & directed by Engr -in-charge |
| 42 | M &L Roof tiles, Mangalore pattern, interlocking at side joints, laid dry all as completed |
| 43 | M&L or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 all as specified |
| 44 | M & L Non asbestos fibre cement building boards 4 mm thick (one side embosed design), fixed or laid/ inserted to Aluminium grid frame work in ceiling with clips all as specified and directed. |
| 45 | M&L in repair for 18/19 mm thick prelaminated particle board, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in cup board shutters, partitions, shelves, cupboard drawers, pelmet boxes and similar work including taking down olds shutters/shelves. |
| 46 | M&L for external teak wood lipping, 6mm thick fixed with nails for particle board of 18/19 mm thick |
| 47 | M&L for repairing of RCC projection, chajja, facia, column etc by necessary preparation (i.e. scraping, cutting, chiseling, dusting and cleaning exposed reinforcement surface of damaged/ loose surface and applying one coat of cement slurry and filling the surface with plain cement concrete (1:1.5:3) reinforced with welded mesh and make good by15mm thick plaster with cm (1:4) and including scaffolding /formwork etc upto double storey height complete all as specified and directed by engineer in charge. |
| 48 | M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed. |
| 49 | M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of floor/ foot path etc and finished the surface complete all as directed. |
| 50 | M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed. Please Enable Macros to View BoQ information |
| 51 | M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed. Please Enable Macros to View BoQ information |
