|
| 1 | Taking down chowkhat or frames n. exc. 1.5 sqm each with shutter without taking off shutter from the frame complete all as specified and directed. |
| 2 | Taking down chowkhat or frames exc. 1.5 sqm but n. exc. 4 sqm each with shutter without taking off shutter from the frame complete all as specified and directed. |
| 3 | Taking down shutters of any description exc. 1 Sqm each and n. exc. 2 Sqm each, complete all as specified and directed. |
| 4 | Taking down shutter from frame exc. 1 sqm but n. exc. 2 sqm each and refixing in same opening after resecuring or easing , and adjusting complete all as specified and directed by Engr-in-charge. |
| 5 | Dismantling of structural steel work including doors, gate but excluding framed truss etc. complete all as specifedand directed |
| 6 | S&F mild steel confirimg to Fe 410-W(Gde-E- 250)quality- A works as in doors or gates (ornamental) of angle or other sectons with gusset plates, rails, braces etc complete drilled, welded etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed |
| 7 | M&L for mild steel plain black sheet 1.25mm thick as in steel gates and similar work, cut to size, hole punched, including round headed screws or rivets and fixed to steel framingwith plain 40mm lap joints with riveted including bending or turning up mitred angles etc as required, complete all as specified and directed. |
| 8 | S&F of collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, including taking down of old unserviceable gate complete all as specified and directed. |
| 9 | S & F of 30 mm thick IInd class hard wood, glazed & skeleton window shutters, open rebated and prepared to receive glass, gauze etc, divided in to square, with plain, chamfered or rounded, mitred and rebated sash bars fitted with cut and mitred beads for securing glass, size of member of shutters shall be as specified in SSR Part-I 2009 section 8 clause 8.24(b), complete all as specified and directed. |
| 10 | M&L for preparation of new previously untreated steel and iron surfaces of any description not other wise described over 10 centimetre width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome complete all as specified and as directed. |
| 11 | S&F 35mm thick, factory made, plain framed, panelled shutter (Two panel) with IInd class hard wood rail & style, lock rail and panel of 9 mm BWP commercial ply or 12 mm thick vaneered particle board with commercial vaneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 12 | M&L for greasing and easing in position of mild steel gate of area exc. 2 Sqm and n.exc 20 Sqm each for full movement and for easy operation for shutters including taking down of old shutter complete all as directed by Engr-in-Charge. |
| 13 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note:- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. |
| 14 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (Note:- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 15 | S& F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 16 | S&F 12 mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for backing of cup boards and bathroom / kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing to wood or steel framing with stainless steel screws etc. complete all as per direction of Engineer-In- Charge. Note: stainless steel screws shall be paid separately |
| 17 | S&F of 4mm thick aluminium composite panel (ACP), ISI marked as in cladding, in wooden flush doors or WPC Doors and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 18 | Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of wood grain printed 5 mm PVC sheet reinforced with MS square tube and edgeswill be painted to match will printed sheet fixed in opening as per specification & drawings complete all as specified and as directed. |
| 19 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube top & bottom rail mild steel frame shall be covered with heat moulded wood grain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing complete all as specified and directed. |
| 20 | S&F of aluminium door / window / ventilator / partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc, including powder coated aluminium fittings such as stainless steel hinges, tower bolts, hooks & eyes, peg stays and handles, concealed star lock for aluminium window, Mortice lock vertical type size 100mm 04 lever for door, rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors including connected items, with and making good to the disturbed portion with its original specifications incl taking down existing members/frame any position complete all as specified and directed by Engr-in-Charge. |
| 21 | S&F of anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 22 | S&F for concealed star lock powder coated for aluminium window fixed as per manufacturers instructions complete all as specified & as directed. |
| 23 | S&F of aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified & as directed. |
| 24 | S&F in repairs to aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified & as directed. |
| 25 | S&F of 4 mm thick Sheet glass, ordinary quality, ground or obscured or frosted, on one side and glazing in wooden, Aluminium, steel frame in square of any size, including hacking out old glass (If any) complete all as specified and as directed. |
| 26 | S&F 4 mm thick Sheet glass, ordinary quality and glazing in wooden, Aluminium, steel frame in square of any size, including hacking out old glass (If any) complete all as specified and directed. |
| 27 | S&F of Aluminium anodized, barrel tower bolt of extruded section, length of bolt 20 mm complete all as specified and as directed. |
| 28 | Demolition of pre-cast concrete block masonary built in cement mortar including all quoins, arches, pillars etc. and pre cast concrete articles complete all as specified and directed. |
| 29 | S&F green marble 18-20mm thick, pre-polished, machine cut, jointing and pointing with white cement slurry including, pointed in white cement mortar 1:2 using marble dust with admixture or pigment to match with the marble shed as in steps, jambs, pillars, window cill & cooking platforms, laid over and including 20mm thick screed bed or bedding layer of mortar in CM 1:4 including dismantling of old stone slab / tiles & bedding layer etc. complete all as specified and directed. |
| 30 | Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc also splays between floors and beams, etc. for flat surface, fair finishes complete all as specified and directed |
| 31 | M&L for PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in coping, bed black / hold fast etc including nessesary form work etc. complete all as specified and directed. |
| 32 | Taking down cement plaster from old brick / stone masonry walls etc. including racking out joints, hacking for keys and scrubbing down with water complete all as specified and directed. |
| 33 | M&L for pre-cast cement concrete block masonry with solid blocks exceeding 10cm in width in type B1 (1:2:4) and setting in mortar (1:6) complete all as specified and as directed |
| 34 | Dismantling AC (Corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified and as directed |
| 35 | S&F of pre-painted galvalume aluminium zinc coating Gl based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws etc. complete as specified and as directed |
| 36 | S&F Pre-painted galvalume aluminum zinc coating Gl based corrugated steel sheet to be used as crimp curve 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed |
| 37 | Demolition of RCC as in slab, beam, chajja, old water tank (other than ground floor) beams staircases, and similar complete all as specified and directed by Engr-in- Charge |
| 38 | Separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately) complete all as specified and directed by Engr-in-Charge. |
| 39 | Material and labour for Reinforced cement concrete nominal mix type B-1. 1:2:4 as in beams, cantilevers, bressummers, lintels over 1.5m span, columns, pillars, Chajja, piers, posts and struts and similar works complete all as specified and directed by Engr-in-Charge. |
| 40 | M&L for rendering 5mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement including sagol finish complete all as specified and directed. |
| 41 | M & L for preparation of new or previously untreated plastered surfaces of walls and applying two coats of acrylic antifungal paint exterior grade paint plain or camouflage pattern on one coat of primer complete all as specified and as directed |
| 42 | M & L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening on plastered surfaces complete all as specified and directed. |
| 43 | M&L preparation of new plastered surface of ceiling and applying three coat of white wash on ceiling complete all as specified and directed. |
| 44 | S&F of Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.Note:-Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced including dismantling of rusted steel complete all as specified and directed. |
| 45 | S&F of 5mm dia and over up to and including 10mm dia additional main TMT steel bar or stirrups of designed diameter in various structural elements like column beams and foundations including drilling, bending, welding and fixing the bars with epoxy putty etc. (Steel provided on the basis of 1% of volume of concrete) complete all as directed by Engr-in-Charge |
| 46 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 47 | M&L for roof trusses (framed) trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle, channel or flat section) including distance pieces etc conforming to Fe 410 W Gde E-250 complete all as specified and directed |
| 48 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed. |
| 49 | S&F mild steel work, Grade Fe-410-0 or Fe- 310-0, as in flat iron holdfast) complete all as specified and as directed |
| 50 | M&L for providing and fixing IS: 12817 marked stainless steel butt hinges of size 100 x 58 x 1.90mm with stainless steel screws etc. Complete all as specified and directed. |
| 51 | S&F of mild steel butt hinges, heavy weight, cold rolled mild steel, and fixed 125 mm long, complete all as specified and directed. |
| 52 | S&F for 300 mm mild steel barrel tower bolts, stove enamelled black with bright bolts and fixed complete all as specified and directed. |
| 53 | S&F 300mm length of bolt, aluminium alloy, anodised, sliding door bolts with hasp staple (bolt type) anf fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy, complete all as specified and directed. |
| 54 | S&F 375 mm long mild steel sliding door bolt clip & bolt type stove enamelled black with bright bolt n.less then 12 mm dia and including a minimium of 6 bolt & nuts, four on bolt plate and two on staple plate complete all as specified and directed. |
| 55 | S&F aluminium (Extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed. |
| 56 | S&F double action floor spring spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main boady with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and directed. |
| 57 | S&F in repairs floor door stopper, over all length of cover plate 140 mm of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in door, complete all as specified and directed. |
| 58 | S&F in repair 3 mm thick translucent white acrylic plastic sheet fixed in wooden, Aluminium, steel frame in square of any size complete all as specified and directed. Please Enable Macros to View BoQ information |
| 59 | S&F in repair 3 mm thick translucent white acrylic plastic sheet fixed in wooden, Aluminium, steel frame in square of any size complete all as specified and directed. Please Enable Macros to View BoQ information |
