|
| 1 | Demolition of cement concrete (unreinforced) in ground floors and paving’s n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed. |
| 2 | M&L for water proofing treatment of sunken floor of WCs bathroom etc by applying of the following specification:-(i) Cleaning of sunken floor surface with mechanical means i.e wire brush/air blower etc and remove all loose/unsound material dirt dust etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite industries Ltd in the ratio 1:2:4 (one part of acrylic polymer: two part of water and four part of cement) (iii) First layer of cement slurry @0.444 kg/sqm mixed with acrylic based modified cementious composite compound @0.222 litre/sqm and allow it to air dry for 4 hour (iv) Second layer of cement slurry @0.222 kg /sqm mixed with acrylic based dified cementious composite compound @0.111 litre/sqm and allow it to air dry for 4 hour followed with water curing for 48 hours (v) 200 micron thick polythen film shall be pasted with help of adhesive over treatment. Note: Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. Testing of all traps and joints and sunken slab shall be done as per IS-1742 before filling and tiling work as directed by Engineer-in-Charge. |
| 3 | M&L for plain cement concrete 1:5:10 type E-2 (using 20 mm graded broken bricks aggregate ) as in foundation and mass concrete complete all as specified and as directed by Engineer-in-Charge |
| 4 | M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors as directed by Engineer-in-Charge. |
| 5 | Supply and laying 32 mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed. |
| 6 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each or as directed by Engineer-in-Charge. |
| 7 | Taking up or down steel tubing 15mm bore and connections including cleaning for re-fixing or removing from site to store complete as directed by Engineer-in-Charge. |
| 8 | Dismantling of cast iron or reinforced concrete drain pipe, jointed in cemented mortar and taking out of trenches or in vertical position of internal dia 100 mm & less all as directed by the Engineer-in-charge. |
| 9 | S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, as directed by Engineer-in-Charge. |
| 10 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with Sqm suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site as per specification & drawing as directed by Engineer-in-Charge. |
| 11 | S&F 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed as directed by Engineer-in-Charge |
| 12 | S&F 300 mm long aluminium alloy anodized sliding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast aluminium alloy as directed by Engineer-in-Charge |
| 13 | S&F for 100 mm long butt hinges, medium weight stainless steel as directed by Engineer-in-Charge |
| 14 | S&F aluminium handles, cast type, anodized, of size 150mm as directed by Engineer-in-Charge. |
| 15 | S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as directed by Engineer-in-Charge. |
| 16 | S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup , screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge. |
| 17 | S&F in repair 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, and screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge. |
| 18 | S&F in repairs 20 mm dia gun metal globe or gate valve with iron wheel head screwed both ends for iron pipes as directed by Engineer-in-Charge |
| 19 | S&F in repair brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union as directed by Engineer-in-Charge. |
| 20 | S&F in repairs PVC connection 15 mm size with nuts of length 450 mm as directed by Engineer-in-Charge. |
| 21 | S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length. 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated. screwed down high pressure, with or without lettered 'Hot' or 'Cold with long screwed shanks and fly nuts, screwed for iron pipe PVC connection 15 mm size with nuts of length 450 mm complete all as specified and as directed by Engineer-in-Charge. |
| 22 | S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including PVC 'P' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish and as directed by Engineer-in-Charge. |
| 23 | S&F in repairs PVC valve less, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets all as directed by Engr-in-charge. |
| 24 | S&F in repair 5.5 mm thick, 600 X 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with CP brass screws and cup washers as directed by Engineer-in-Charge. |
| 25 | S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long all as directed by Engr-in-charge |
| 26 | S&F PVC (SWR) gully traps of size 125/110 mm, setting and jointing with solvent cement and complete and as directed by Engineer-in-Charge. |
| 27 | S&F PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors as directed by Engineer-in-Charge |
| 28 | S&F PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints fixed in walls as directed by Engineer-in-Charge |
| 29 | S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors as directed by Engineer-in-Charge |
| 30 | S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints but fixed in walls as directed by Engineer-in-Charge |
| 31 | S&F in repair for PVC (SWR), junction single, (Single T) with door 110 mm dia equal or unequal as directed by Engineer-in-Charge |
| 32 | All as per item No. 31.00 here-in-above, but 75 mm dia as directed by Engineer-in-Charge. |
| 33 | S&F in repair for PVC (SWR) door bends 110 mm dia as directed by Engineer-in-Charge |
| 34 | All as per item No.33.00 here-in-above, but 75 mm dia as directed by Engineer-in-Charge. |
| 35 | S&F in repair for PVC (SWR) Cowl 110 mm dia as directed by Engineer-in-Charge |
| 36 | S&F in repair for PVC (SWR), 75mm dia of floor trap, with grating including jointing with solvent cement and complete and as directed by Engineer-in-Charge. |
| 37 | S&F in repair CP tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and all as specified and directed by Engineer-in-Charge |
| 38 | S&F in repair CP grating 100 mm dia all as specified and as directed. |
| 39 | S&F in repairs stainless steel plate rack 0.56mm thick of standard pattern of size 750x600x250 mm complete as directed by Engineer-in-Charge |
| 40 | S&F in repair sink made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32mm bore and of Each suitable length, all as directed by Engr-in-charge. |
| 41 | S&F in repair 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) as directed by Engineer-in-Charge. |
| 42 | Cutting chases stone concrete blocks pinning in making good to facing where required and pointing in CM 1:3 to ends or edge of landing steps cills sunshades shelves lintels etc and cutting chases for concealed water tubing making good not exceeding 10 cm girth for stone walls as directed by Engineer-in-Charge. |
| 43 | M&L for joint free nonskid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge. |
| 44 | M&L for glazed ceramic tiles, coloured, 450x300x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone or brick masonry surfaces as directed by Engineer-in-Charge. |
| 45 | M&L for granite (of any type ) tiles 20 mm thick machine cut in skirting /dado over and including 10 mm thick rendering in CM 1:4 on stone masonry surfaces jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed by Engineer-in-Charge |
| 46 | S&F MS powder coated louvers with including arrangement of fixing glass pinhead as per size & louvers ventilators (Glass shall be measured separately ) complete all as specified and as directed |
| 47 | M&L for taking down cement or cement lime plaster any description incl racking out joints, hacking for key , scrubbing down with water etc including removal of debrish from the MOD land complete all as specified and directed. |
| 48 | M& L for 15 mm thick rendering on block masony or concrete surfaces in CM 1:6 on internal walls at any height, finished even and smooth without using extra cement and all as specified. |
| 49 | M& L for 10 mm thick rendering on ceiling surfaces in CM 1:3 on finished even and smooth without using extra cement and all as specified. |
| 50 | M&L for 15mm thick rendering on block masonry of concrete surface in CM 1:4 on external wall at any height, finished even and smooth without using extra cement complete all as specified and directed. |
| 51 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted including removing existing nails, if any, any Nos and filling the disturbed surface/holes making smooth surface as directed |
| 52 | M&L for preparation of new surface of ceiling and applying two coat of applying two coats of oil emulsion distemper white or tinted over a coat of primer complete all as specified and directed |
| 53 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer, white or tinted, upto 20 m height from ground leven all as directed. |
| 54 | S&F in repair Stainless steel curtain rod with and including fancy type SS fixing brackets, stops rollers etc complete all as directed by Engr-in-charge. |
| 55 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 56 | M&L for Vetrified Ceramic tiles(light shade) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cm 1:6 Complete all as specified and directed. Please Enable Macros to View BoQ information |
