|
| 1 | Exacavation in trenches n etc. 1.5m wide n exc 1.5m depth and getting out in hard / dense soil including trimming bottom surface to require level and slope complete all as directed by Engr-in-Charge.Note:- Taking up pipe with fitting, special valves etc. from trench shall be measured and paid separately. |
| 2 | Returning , filling in including spreading, levelling , watering & well ramming in layers n.exc 25cm including making good disturbed surface to original levels complete all as specified and directed |
| 3 | Removal of exacavation material to a distance n exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed |
| 4 | Deploying labour with tools for removing grass, shrubs, trimming branches of trees in water supply installation and water reservoir and shifting of debris to a distance of 50 mtr away from site complete all as directed by Engineer -in-Charge |
| 5 | Taking out cast iron / ductile iron water mains (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead for the following size of pipes:- Note :- Excavation and earth work required shall be measured and paid separately under relevant items.(a). 200mm bore |
| 6 | (b) 150 mm bore |
| 7 | (c) 100 mm bore |
| 8 | Supply, laying, jointing & testing DI-K9 class with spigot, socket and flanged, suitable for Push on rubber joint / fanged joint with internal cement mortor lining, and external zinc and black bitumen coated pipes in any lengths conforming to IS:8329-2000 including Rubber Gasket & joints as per IS:9523-2000 laid in trenches/ Road/ Ducts/ Footpath / on wall/ on floor locations complete all as specified and directed by Engr-in Charge for the following sizes of pipes:-(a). 200mm bore |
| 9 | (b) 150 mm bore |
| 10 | (c) 100 mm bore |
| 11 | Taking down existing DI specials and S&F of new DI specials such as bends (any type, radius, tapers) and any type (straight, bend, increasing, decreasing, or double socket ect), Tee pieces single branch 'Y' junction double branch, cross (all sockets or socket and spigot), collars caps and plugs ect for upto 250mm bore as in repair including complete all as specified and directed. |
| 12 | Burning out existing lead joints of CI pipes including cleaning and collecting old lead complete all as directed by engineer-in-charge for the following bore of pipes:-Note:- Excavation and earth work required shall be measured and paid separately under relevant items. (a) 150mm bore |
| 13 | (b) 100 mm bore pipe |
| 14 | (c) 80 mm bore pipe |
| 15 | M&L for run lead joints in position for spigot socket pipe and specials including provision of all jointing materials such as pig lead, lead spun yarn / joint etc. complete all as directed by engineer-in-charge for the following bore of pipes:-(a) 150mm bore |
| 16 | (b) 100 mm bore |
| 17 | (c) 80 mm bore |
| 18 | Taking down old unserviceable existing sluice valve and supply and fixing of new sluice valve in position (ISI marked) flanged and drill both ends cast iron body, heavy duty brass spindle type PN 1.6 with and including jointing rubber gasket, nut, bolts complete all as specified and directed by engineer-in-charge for the following size of sluice valve:-(a) 150mm bore |
| 19 | (b) 100 mm bore |
| 20 | (c) 80 mm bore |
| 21 | Demolition of unserviceable broken valve chamber of any size and M&L for construction of new wall chamber with brick masonry valve chamber 900mm x 900mm x 900mm (internal size) 15cm thick foundation using PCC (1:4:8) type D2 using (40mm graded stone augregates) 23cm thick brick walls built in CM (1:6) 10mm thick internal paster & external plaster in CM (1:4)on internal wall surface of chamber and external surface upto 15cm below the ground level finished even & fair 5mm MS sheet cover including 40 x 40 x 0.6mm angle iron frame fixed on 150mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in coping with and including necessary use and waste of form work with and including 25mm x 6mm flat iron hold fasts, handles, hinges with locking arrangement applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces including necessary returning, filling, including desposal of surplus soil etc. complete all as specified and as directed by Engr-in-Charge. |
| 22 | Taking down of old unserviceable existing ladder and S&F of new ladder at OHT and UG sumps as per existing specification with cross arms, baracings, supports, clamps and back plates fabricated from structural steel section including Nuts, Bolts, washers, welding, bending cold or hot, driiling holes for bolts in any shape or size las indicated or directed and inclusive of one coat of red oxide primer, one under coat and one finishing coat of paint complete all as specified and as directed. |
| 23 | M&L for PCC 1:2:4 type B2 ( using 40mm graded stone aggregate) for foundation, filling, mass conceret and thrust block for supporting pipe lines including necessary form work etc. Complete all as specified and directed by engr -in- charge. |
| 24 | Taking out unserviceable rusted steel water tubing (including all fittings) and connection including removal from site complete all as specified and directed for the following sizes of pipes:-Note :- Excavation and earth work required shall be measured and paid separately under relevant items.(a) 15 mm bore |
| 25 | (b) 20 mm bore |
| 26 | (c ) 25 mm bore |
| 27 | (d) 40 mm bore |
| 28 | (e) 50 mm bore |
| 29 | (f) 80 mm bore |
| 30 | Supply and laying GI tubing medium grade in trenches / wall / floors including all required fittings & fixtures as required at site complete all as specified and directed for the following sizes of pipes:-(a) 15 mm bore |
| 31 | (b) 20 mm bore |
| 32 | (c ) 25 mm bore |
| 33 | (d) 40 mm bore |
| 34 | (e) 50 mm bore |
| 35 | (f) 80 mm bore |
| 36 | S&F in repairs Cast Iron Body, ISI Marked Foot valve suitable for 80 mm dia pipe line including all fittings complete all as specified and directed by Engr -in- Charge. |
| 37 | S&F in repairs Cast Iron Body, ISI Marked, Flange end Foot valve suitable for 100 mm dia pipe line including nut, bolts, gasket and washers complete all as specified and directed by Engr -in- Charge. |
| 38 | S&F in repairs / replacment of 100 mm more CI non return valve, flanged type, ISI marked with by pass arrangement complete all as specified and dirrected. |
| 39 | S&F in repairs / replacment of 80 mm more CI non return valve, flanged type, ISI marked with by pass arrangement complete all as specified and dirrected. |
| 40 | Supply and fixing in repairs cast Iron Air Valves with double air Outlets, conforming to IS 14845 of 100 mm dia bore and fixing up in Cast Iron Water supply mains of sizes complete all as specified and directed. |
| 41 | S&F in repairs and replacement of Rotational Moulder PVC /HDPE water storage tank of capacity 2000 litres (Cylindrilcal Vertical with closed top) two layered with ISI marked hoisted including with all accessories (union, washer coupling etc) covers, connecting up pipes fixed in position complete all as specified in SSR Part-I and directed by Engr-in-Charge. |
| 42 | S & F in repairs / replacement of gunmetal globe or gate valve, with iron wheel head, screwed both ends for iron pipe confirming to latest relevant IS as required at site complete all as specified and directed for the following sizes:-(a) 15 mm dia valve |
| 43 | (b) 20 mm bore Valve |
| 44 | (c) 25 mm bore Valve |
| 45 | (d) 40 mm bore Valve |
| 46 | (e) 50 mm bore Valve |
| 47 | (e) 80 mm bore Valve |
| 48 | M&L for repairs to CI mechanical joints suitable for CI/DI pipe with all accessories such as CI sleave, CI outer rings,rubber gaskets,GI bolt,nut,washer ect all as directed by Engr-in-chrage and suitable for the following size of pipes:-(a) 150 mm bore |
| 49 | (b) 100 mm bore Please Enable Macros to View BoQ information |
| 50 | (b) 100 mm bore Please Enable Macros to View BoQ information |
