|
| 1 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site complete all as specified and directed and making good disturbed surface of walls in cement mortar (1:3) all as specified and directed. |
| 3 | Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf and removing from site all as specified and directed |
| 4 | M & L for rolled mild steel work angle iron as in door frame (Chowkhats) / cooler stand and other similar work including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed. |
| 5 | S & F second class Hardwood 35 mm thick, factory made, plain framed, panelled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed. |
| 6 | S & F Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels commercial type on both side and both faces is covered with approved pattern with Decorative coloured laminate on both face type 1 of 0.9 mm thick and all around side faces covered with 7-10mm thick 1st class hard wood liping duly polished complete all as per specified and directed. |
| 7 | M&L for factory made Second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (incl sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 incl glass and wiremesh complete all as specified and directed. |
| 8 | S & F for for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour sheet PVC Sheet rinforced with M.S square tube,fixing in opening as per specification & Drawing complete all as specified and directed. |
| 9 | S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed. |
| 10 | S & F in repair Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge, including required wiremess and sheet glass(Plain/figured) etc in complete window, including holes, cutting holes for hold fast,neccesary fittings and making good in PCC 1:2:4 type B-1, including synthetic enamel paint two coat over a coat of zinc chrome red oxide primer incl glass and wiremesh etc complete all as specified and directed. |
| 11 | S & F for fixed type ventilators aluminium powder coated of frame size 50.80x25.40mm, 1.5mm thick half portion will be fixed with 4mm thick frusted glass and half portion will be fixed with louvers with 4mm thick frusted glass with rubber gasket and aluminium beading, aluminium grill with fixing arrangement (weight of grill not less than 2.50Kg/sqm) aluminium wire mesh 0.45mm dia to be fixed over louvers portion only including necessary cutting holes on wall and fixing arrangements complete all as per sample kept in GE office. (AL section thickness 1.50mm) |
| 12 | S & F for Solid PVC moulded Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing using single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed. |
| 13 | S & F for factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam (Nut Brown colour ) PVC sheet on the front face & 2mm prelam (Nut Brown colur ) PVC sheet on back face, and fixing inthe frame at site as per specification and drawing on page 161 of SSR (Part -II ) 2020 complete all as specified and directed. |
| 14 | M&L for preparing the new wooden surface & applying two coats of synthetic enamel paint (1st grade) over one coat of pink primer over 10Cm width or girth complete all as spd & directed. |
| 15 | M&L preparing new steel or iron surfaces of any description, exc 10cm in width or girth and two coats of synthetic enamel Paint over a coat of red oxide primer complete all as specified and directed |
| 16 | M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in fixing of hold fast and other similar work complete all as specified and directed. |
| 17 | S & F for in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples fixed all as specified and directed |
| 18 | Hacking out old broken glass (any thickness, size quality or description) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new one and S & F for 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed. |
| 19 | S & F sheet glass, ordinary quality 5.5mm thick fixed in repairs with oil putty size of glass not exc 0.50 Sqm in each pane for steel or wooden windows/doors fixed with wooden beadand pin tacked complete all as specified and directed. |
| 20 | S & F for mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed. |
| 21 | M&L mild steel 300mm ordinary rat tail rod patttern springs includding roller and roller plate complete all as specified and directed. |
| 22 | M&L in repairs mild steel 300mm ordinary rat tail rod patttern springs includding roller and roller plate complete all as specified and directed. |
| 23 | S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 24 | S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed. |
| 25 | S & F in repair aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed. |
| 26 | S & F for aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed. |
| 27 | S & F for in repair aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed. |
| 28 | S & F for butt hinges 100mm size stainless steel complete all as specified |
| 29 | S & F for in repair butt hinges 100mm size stainless steel complete all as specified |
| 30 | Taking down plaster of any description including raking out joints, hacking for key scrubbing down with water on wall / ceiling complete all as specifid and directed |
| 31 | M& L for 15mm thick rendering in cement mortar (1:6), on stone masonary surfaces finished even and smooth complete all as specified and directed |
| 32 | M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over 1 mm thick wall putty all as specified & directed. |
| 33 | Taking down of aluminium door and window (n. exc 4 sqm) from existing frame and replace the glass joining cleat/ glazing clips & rubber neoprene packing of glass and refix the glass in panel, incl refixing the loose stile of door and window with reqd aluminium cleats, new glass etc, complete and refix the panel shutter with frame complete all as specified and directed. |
| 34 | Taking down pelmet/curtain rod any size with rod and bracket fixed to wall complete all as specified & directed. |
| 35 | S & F for 25mm dia stainless steel curtain rod heavy duty with a pair of decorative Curtain Finials/ knob & heavy Curtain Support Bracket for rod made of stainless steel, etc. complete all as specified & directed. |
| 36 | S & F for in decorative type knobs with bracket of stainless steel fixing at end of curtain rod complete all as spd & directed. |
| 37 | S & F in repair aluminium door shutters with frame of aluminium section including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mm x 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor door spring made up of 1.25mm thick aluminium alloy sheet foundation box for each shutter, etc and incl fitted with 5mm thick tinned glass in glazed shutter with brass mortice lock 100mm 2 levers, vertical type complete all as specified and directed |
| 38 | M&L in repair aluminium powder coated sliding window, ventilator three track including aluminium powder coated decorated grill sliding shutter 5mm thick tinted float glasses, necessary aluminium beadings fittings and other panels to prevent air from out side complete all as specified and directed and as per Chief Engineer Drg No CEBZ/TD/15/2011 |
| 39 | Repair to steel window / gate including necessary welding, reivting, easing drilling and replacement of unserviceable hanging device,glass pane,wiremmesh and making them in serviceable condition complete all as specified and directed. |
| 40 | Demolition of brick work or stone/boulder masonary built in cement mortar of any specification and in any position complete all as specified and directed. |
| 41 | M&L for walling random rubble masonary(but except stone) uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc complete all as specified and directed. |
| 42 | M&L for walling random rubble masonary uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc complete all as specified and directed. |
| 43 | M&L for brick work with flyash old size bricks, straight or curved on plan exc. 6mm mean radius, built in in cement mortar 1:6.complete all as specified and directed |
| 44 | S & F for for 18mm thick PVC board of one side prelaminated or digital finished and other side plain white colour to make kitchen cabinet shutter/drawer front shutters complete with and including all fittings and fixtures as per specifications complete all as specified and directed. |
| 45 | S & F for for 18mm thick PVC board both side plain white colour fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete with and inculding all fittings and fixtures as per specifications, complete all as specified and directed |
| 46 | S & F false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness(as per IS: 14862) of size 595x595 mm and any one of the desin (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length, and 15x32mm made from 0.30 mm thick sheet, and cross \\"T\\" of size 15x32mm made of 0.30 mm sheet, spaced between main \\"T\\" at 600mm c/c to form a grid of 600X600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixures,smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin,etc with dash fasteners,GI adjustable rods of 3mm dia with gavanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T-sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all height and dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 47 | Dismantling of ceiling board/lathing any thickness complete all as specified and directed |
| 48 | S&F 5 mm thick Hollow PVC wall paneling of any colour inclusive of solvent cement and fixing at site on including of 5 mm thick PVC sheet fillet of width 35 mm for wall paneling including dismantling of old existing wall paneling complete all as specified and directed. |
| 49 | M&L for aluminium partition in repairs using aluminium sections fitted with 5mm thick tinted glass in upper portion from 3' height as required as per site and 12 mm thick prelaminated particle board both side of standard quality of approved make, any type upto 3' height as required as per site from bottom using glazing clips including jointing cleat for fixing glazing clips, rubber packing anodised aluminium beading etc aluminium tower bolt, floor stoper and locking arrangement by providing latch lock of standard quality of approved make complete all as specified and directed |
| 50 | M & L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edges of stone slabs one edge, complete all as specified and directed. |
| 51 | Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed. |
| 52 | M&L for Glazed ceramic tiles coloured (450x300mm) x 7mm thick, in wall tile/vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat of tiles in CM (1:4) complete all as spd |
| 53 | M & L for Non-skid Ceramic tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured in white or coloured cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed. |
| 54 | S & F in repair sheet glass, ordinary quality 5.5mm thick fixed in repairs with oil putty size of glass not exc 0.50 Sqm in each pane for steel or wooden windows/doors fixed with wooden beadand pin tacked complete all as specified and directed. |
| 55 | S & F for Deco door seal 1.5\\" width gate bottom sealing strip draft excluder stopper with aluminium plate and nylon bristles for weather stripping, air sound slocking complete all as specified and directed. Please Enable Macros to View BoQ information |
| 56 | S & F for Deco door seal 1.5\\" width gate bottom sealing strip draft excluder stopper with aluminium plate and nylon bristles for weather stripping, air sound slocking complete all as specified and directed. Please Enable Macros to View BoQ information |
