|
| 1 | Demolition of cement concrete in floors and pavings n exc 15 cm thickness (below or above ground level) and of any description and in any position not otherwise specifically provided all as specified and directed by Engineer-in-Charge. |
| 2 | M&L for 50mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floor and finished even and smooth without using extra cement complete all as specified and directed. |
| 3 | M&L for 40 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) and finished the surface even and smooth without using extra cement with glass dividing strip as in floor including demoliation of existing flooring, complete all as specified and directed. (Note: Glass dividing strip shall be measured and paid for separately). |
| 4 | M&L for providing glass dividing strip 3mm thick and 38 mm wide inserted in position, conform to design in PCC flooring complete all as specified and directed. |
| 5 | Dismantling of asbestos cement corrugated or semi corrugated sheets in roof covering of any gauge and thickness complete all as specified and directed. |
| 6 | M&L for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roofs; walls etc fixed with L-type or J type or cranked hook bolts with bitumen washers complete all as specified and directed. |
| 7 | All as per Srl item No 06 above but except sheets. |
| 8 | M&L for 6mm thick asbestos cement, two piece adjustable plain wing ridge, fixed with L-type or J type or cranked hook bolts with bitumen washers complete all as specified and directed. |
| 9 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 10 | M&L for exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with celulose fibre for fixing over and including GI powder coated grid work of size 605mm X 605mm, with main tee of size 32mm X 23.5mm x 1.5mm thick, cross tee of size 25mm x 23.5mm x 1.28mm and angle of size 23.5mm X 23.5mm x 1.2mm fixed on wall, all powder coated finish on exposed faces of tee and angle, hung from ceiling using 2mm dia. G.I. suspension wires and 'J' bolts, washers, nuts spaced at 1200 mm both ways including making niches for fans/ light all as specified and as directed. complete all as specified and directed. |
| 11 | M&L for 6mm thick plain AC building boards fixed to timber frame work/ fillet with screws in ceiling flat or sloping complete all as specified and directed. |
| 12 | Dismantling timber scantlings 40 sqcm and over in section, in any position of framed work complete all as specified and directed. |
| 13 | M&L for 2nd class hard wood plain fillet square, rectangular or triangular exc 6 sqcm but n. exc 13 sqcm in section, clean sawn, secured with screws complete all as specified and directed. |
| 14 | M&L for timber scantling of second class hard wood, clean sawn, framed work as in ceiling fixed with nails complete all as specified and directed. |
| 15 | S&F in repair steel work in tubular trusses incl special shaped washers etc using ERW or induction but welded tubes conforming to IS 1161- 1979 grade St-240 complete all as specified and directed. |
| 16 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws including dismantling of existing steel sheet complete all as specified and directed. |
| 17 | S&F galvanised, corrugated mild steel sheeting 0.63mm thick with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws and washers in roofs, wall etc with grade of zinc coating 275 including dismantling of old sheeting, any gauge, thickness complete all as specified and directed. |
| 18 | M&L preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with one coat of creosote oil complete all as specified and directed. |
| 19 | M&L for glazed ceramic coloured tiles of size 450x300x7mm thick on and including 10mm thick screed bed in CM (1:4) set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado including taking down existing tiles with bedding for complete all as specified. |
| 20 | M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles on 15 mm thick screed bed in CM 1:6 including taking down existing tiles with bedding complete all as specified. |
| 21 | M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles on 15 mm thick screed bed in CM 1:6 including taking down existing tiles with bedding complete all as specified. |
| 22 | M&L for vitrified coloured ceramic tiles 9 to 10 mm thick joint free (square/ rectangular) area of each tile not exceeding 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles on 15 mm thick screed bed in CM 1:6 including taking down existing tiles with bedding complete all as specified and directed. |
| 23 | S&F machine cut kota stone slab flooring 18 to 20mm thick over cement screed base 15mm thick in 1:4 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) complete all as specified and directed. |
| 24 | M&L for green marble work 14-16 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 incl dismantling of existing marble with screed complete all as specified and directed. |
| 25 | Demolition for stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc incl removal of debries from premises complete all as specified and directed. |
| 26 | M&L for 75mm thick cement cocnrete 1:3:6 type C-1(using 20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand (all by weight) complete all as specified and directed. |
| 27 | M&L for flush pointing to brick tiles laid flat in roof or pavings in CM 1:3 incl racking out joints/ pointing complete all as specified and directed. |
| 28 | Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. |
| 29 | M&L for brick work with fly ash bricks straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 30 | M&L for brick work with fly ash bricksbricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 31 | M&L for repairing of RCC projections, chajjas, roofs, facia etc. by chipping off existing loose, damaged concrete and welding mesh and applying two coats of polymer modified cementitious mortar on epoxy bond coat on dry sub strate & free from debries / dust surfaces of concrete including form work complete all as specified and directed by the manufacturer. (Cost of form work shall be deemed to be included in unit rate quoted by the Contractor). |
| 32 | M&L for rendering 15mm thick ready mix mortar of approved makes on brick or concrete surfaces of walls, finished surface even and fair including taking down cement plaster of any description, complete all as specified and directed.(Note : WPC shall be measured and paid for separately). |
| 33 | M&L for rendering 12mm thick ready mix mortar of approved makes on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement including taking down cement plaster of any description, complete all as specified and directed. |
| 34 | M&L for rendering 5mm thick ready mix mortar of approved makes on ceiling finished surface even and smooth without using extra cement including taking down cement plaster of any description, complete all as specified and directed. |
| 35 | M&L for preparation of newly plastered surface and applying two coats of cement base paint on wall complete all as specified and directed. |
| 36 | M&L for preparation of new plastered surface and applying two coats of oil bound distemper on wall over a coat of primer and 1 to 1.5mm thick acrylic damp proof wall care putty complete all as specified and directed. |
| 37 | M&L for preparation of new plaster surface, plain AC sheets and applying three coats of white wash on ceiling complete all as specified and directed. |
| 38 | M&L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour with mechanical sander having RPM of 1500 - 2700 rpm with internal dust extraction system for clean environment and preparation of old plastered/scrapped surfaces of wall/ceiling by filling cracks by external wall putty/crack fill paste and applying exterior water proof wall care putty @ 1 Kg (undiluted) per sq mtr of average thickness 1mm to 2mm over the prepared plastered wall/ceiling surfaces, one or more coats and grinding the putty surfaces with mechanical grinder for make the surface even and smooth for receiving primer and Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as directed by Eng-in-charge. (Note: Paint using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed make). |
| 39 | M&L for preparation of newly plastered surfaces on wall/ roof projections including facia, cornices, chajja etc and applying exterior water proof wall care putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1mm to 2mm over the plastered wall/ceiling surfaces, one or more coats and grinding the puttied surface with mechanical grinder for make the surface even and smooth for receiving primer and applying Two or more coats of 100% Premium acrylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/ 10 sqm diluted with water as per manufacturers instructions over and including priming coat of exterior waterproof primer applied @ 0.9 litre (Undiluted) / 10 sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:-Paint to be applying with using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed. |
| 40 | M&L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and applying one coat of white wash complete all as specified and directed. |
| 41 | M&L for preparation of old plastered surface of walls by brooming down, making good holes, cracks etc applying one coat of white wash on complete all as directed by Engr-in-charge. |
| 42 | S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of priming and two coats of synthetic enamel paint and taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (Note: Wire cloth, glass, shall be measured and paid for separately). |
| 43 | S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1(using 20mm graded crushed stone aggregate) for hold fasts, including one shop coat of priming and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. (Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately ). |
| 44 | S&F anodised aluminium door shutters, aluminium section weighing not less than 1.00kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos of 150mm long in each door, hinges, anodised aluminum snap beading screws etc. including taking down old existing shutters complete all as specified. |
| 45 | S&F anodised aluminium window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 no.) suitable handle (1 no.) of 150mm long including taking down old existing shutters complete all as specified. |
| 46 | S&F anodised aluminium frame for doors, windows, ventilators, with one or more rebates including joining cleat for fixing etc. including taking down old existing frame complete all as specified |
| 47 | S&F aluminium anodised grill of 5mm thick (transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design / pattern with approved standard section and fixed to the existing window frame with suitable aluminium channel and CP brass / stainless steel screws @ 200mm centre to centre including cutting the grill to proper opeing size for fixing and operation of handles and fixing approved anodised aluminium standard section alround the opeing complete all as specifed and directed. |
| 48 | S&F 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 1.00 sqm in each pane in aluminium door or window shutter complete all as specified and directed |
| 49 | S&F in repair 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 1.00 sqm in each pane in aluminium door or window shutter with rubber packing, anodised aluminium snap beading complete all as specified and directed |
| 50 | S&F of 4mm thick aluminium composite pannel (ACP) sheet for aluminium door/window complete all as specified and directed. |
| 51 | S&F in repair 4mm thick aluminium composite pannel (ACP) sheet for aluminium door/window complete all as specified and directed. |
| 52 | S&F in repairs mortice lock, aluminium vertical type size 100mm 4 levers complete all as specidfed and directed. |
| 53 | Petty repair to existing in built aluminium door, locks, hinges including making/ adjusting the lock/glass/ shutter serviceable complete all as per existing pattern as directed by Engineer-in-Charge including provision of duplicate keys as required. |
| 54 | S&F in repair aluminium (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 55 | Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed. |
| 56 | Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter from the chowkats) complete all as specified and directed. |
| 57 | Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter from the chowkats) complete all as specified and directed. |
| 58 | S&F pressed steel frame for doors with one or more rebate including necessary lugs, hinges, lock strike, plate etc complete of size 105mmx60mm including filling PCC 1:3:6 type-B-1(using 20mm graded crushed stone aggregate) as in the frames including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and directed. |
| 59 | All as per Srl item No ___ above but size 125mm x60mm. |
| 60 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, as per specification & drawing complete all as specified and directed. |
| 61 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, as per specification & drawing complete all as specified and directed. |
| 62 | S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 63 | S&F 2nd class hard wood glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) ; fitted to chowkats complete all as specified and directed. |
| 64 | S&F factory made WPC door frames of size 45 x 70mm, single extruded comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specification of the manufacturer and as specified and directed by Engineer-in-Charge. |
| 65 | S&F 30 mm thick factory made snatural fiber composite door shutter with CNC cutting of required size having minimum 40% high strength plant derived fibers, consisting of thermoset polymers, non-toxic additives ( minimum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum, modules of elasticity (3-4), screw withdrawal strength of 1800 N (Face) & 900 N (Edge), having interlaminar shear strength and thermal stability complete all as per specification of the manufacturer as as specified and directed by Engineer-in-Charge. |
| 66 | S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 67 | S&F in repairs for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 68 | M&L for preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. |
| 69 | M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 70 | M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 71 | S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc. 0.50 Sqm each complete all as specifiwd and directed. |
| 72 | S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares nexc 0.50 Sqm each including hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed. |
| 73 | S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs,including roller and roller plate, fixing through welding/bolt in metal/wooden frame or necessary alternative arrangements to be done complete all as specified and directed. |
| 74 | S&F aluminium anodized barel tower bolt of extruded section 150mm long complete all as specified and directed. |
| 75 | S&F aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed. |
| 76 | S&F 100mm size medium weight mild steel butt hinge fixed with metal surface through bolt or screw or welding complete all as specified and directed. |
| 77 | S&F aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. |
| 78 | S&F in repairs, 20mm dia anodised aluminium alloy harrison rails (curtain rod ) including brackets, stops, rollers etc fixed to wall with screws, PVC plug complete all as specified and directed. |
| 79 | S&F in repair 18/19 mm thick one side prelaminated colour WPC board for cup board shutter and frame & fixed at site complete alll as spcecified and directed. (Note : Board edges properly fnished with strip on band or edges). |
| 80 | S&F in repair self closing box type hinges 35mm of 0 crank (KH-001) or 8 crank (KH-002) openableat 110 degree for kitchen cabinet shutters, complete all as specified and directed. |
| 81 | S&F in repair 100mm size stainless steel handle for kitchen cabinet shutters, complete all as specified and directed. |
| 82 | S&F ball bearing runners 45mm Telescopic (KTS-20) full extension load capacity 50 Kgs, complete all as specified and directed. |
| 83 | S&F chromium plated stainless steel wire basket (storage basket) pull out type for large utensils, size 480 x 500 x 150 mm of Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. |
| 84 | S&F chromium plated stainless steel wire basket (cup and saucer basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. |
| 85 | S&F chromium plated stainless steel wire basket (plate basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. |
| 86 | S&F chromium plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. |
| 87 | S&F chromium plated stainless steel wire basket (grain trolley) pull out type, size 480 x 500 x 200 mm grade 304 with necessary sliding frame structure, fixing clips etc fixed in repair complete all as specified and directed. |
| 88 | S&F chromium plated stainless steel wire basket (bottle pull out) pull out type two shelf size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc fixed in repair complete all as specified and directed. |
| 89 | S&F in repair continuous (piano) hinges, mild steel , bright finish or electro galvanised of 40mm width of flaps complete all a sspecified and directed. |
| 90 | S&F in repair 75mm size hasp and staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 91 | S&F in repair 7-8 mm thick PVC hollow wall panelling consisting of wood grain printed pvc sheet inclusive of solvant cement and fixing at site on PVC frame formed by sticking high density EPS, flame retardent (TF) grade, heavy duty with tipper strip weather proof, water proof, termite proof including all C and U type PVC section with matching of panelling fixing at border of panelling and complete all as specified and directed. |
| 92 | Supply & fix 1000 litres capacity rotational moulded polyethylene triple layered water storage tanks white ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I, including 20mm bore ball valve high prssure of PTMT, with epoxy coated aluminium rod & high density plastic ball, dismantling of existing water tanks complete all as specified and directed. |
| 93 | Supply & fix 500 litres capacity rotational moulded polyethylene triple layered water storage tanks white (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I, including 20mm bore ball valve high prssure of PTMT, with epoxy coated aluminium rod & high density plastic ball, dismantling of existing water tanks complete all as specified and directed. |
| 94 | S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm - 210 gms / 25mm-455gms/ 40mm - 690 gms)complete all as specified. |
| 95 | S&F in repair stop valves or angle valve 15mm bore fancy type cast copper alloy, chromium plated with crutch or butterfly handle screwed down, high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified and directed. |
| 96 | S&F in repair bib tap cast copper alloy chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. |
| 97 | S&F in repair 15mm bore pillar tap, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long shank screwed for iron pipe complete all as specified and directed. |
| 98 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 99 | S&F in repair brass chromium plated shower rose fancy type 125mm size with swivel joints, including fixing to steel pipe or union with brass CP arm 225mm long, 15mm size complete all as specified and directed. |
| 100 | S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts ,white and plastic seat cover white with flat bottom and cover and mild steel chromium plated or aluminised hinging device, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed. |
| 101 | S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with integral foot rest, including connection to trap and flushing pipe and bedding in PCC 1:7:12 (type F-2 using 40mm graded stone aggregate) complete all as specified and directed. |
| 102 | S&F in repair, vitreous china wash hand basin, white flat back, size 550mm x 400mm including brackets, brass CP waste coupling, cutting for and pinning in ends of bracket complete all as specified and directed. |
| 103 | Supply and fix in repair vitreous China half stall type urinal , white, with brass CP spreader including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement paste, 32mm dia PVC flush pipe and discharge pipe, grating and union for discharge pipe,urinal spreader complete all as specified and as directed. |
| 104 | S&F in repair PVC low level duel flushing cistern 10ltr capacity, with syphonic action PVC float valve and 32mm bore PVC flush pipe etc complete all as specified and directed. |
| 105 | S&F in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash fitting of wash basin and sink all as specified and directed. |
| 106 | S & F in repair PVC connections 15 mm size with PTMT nuts, of length 600 mm complete all as specified and directed. |
| 107 | S&F in repair grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms) complete all as specified and directed. |
| 108 | S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed. |
| 109 | S&F in repair GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings including taking up or down existing pipe complete all as specified and directed. |
| 110 | S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings including taking up or down existing pipe complete all as specified and directed. |
| 111 | Dismantling of cast iron, PVC or SGSW pipes any bore , with any type of joints, fixed to wall, taking out of trenches , if required. |
| 112 | S&F PVC (SWR) pipes 110mm bore in any length with rubber ring joints laid in floors/ fixed to wall complete all as specified and directed. |
| 113 | S&F PVC (SWR) pipes 75mm bore in any length with rubber ring joints laid in floors/ fixed to wall complete all as specified and directed. |
| 114 | S&F PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed. |
| 115 | S&F PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed. |
| 116 | S&F 100mm bore PVC (SWR) branch piece, junction single (Single T), equal or unequal with access door complete all as specified and directed. |
| 117 | S&F 75mm bore PVC (SWR) branch piece, junction single (Single T), equal or unequal with access door complete all as specified and directed. |
| 118 | S&F PVC (SWR) vent cowl of size 110mm bore complete all as specified and directed. |
| 119 | M&L in repair PVC (SWR) floor trap plain with stainless steel grating including jointing with solvent cement 100mm dia of outlet complete all as specified and directed. |
| 120 | M&L in repair PVC (SWR) floor trap plain with stainless steel grating including jointing with solvent cement 75mm dia of outlet complete all as specified and directed. |
| 121 | S&F stack clamps (for 110mm bore pipe) out of 20x1.5mm galvanised mild steel flat incl stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 122 | S&F stack clamps (for 75mm bore pipe) out of 20x1.5mm galvanised mild steel flat incl stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 123 | S&F in repair 600mm x 450mm bevelled edge mirror 5mm thick of selected quality glass fancy type as approved by GE and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 124 | S&F in repair stainless steel L-type jet spray with 1m hose pipe for fitting in WC complete all as specified and directed by Engineer-in-Charge. |
| 125 | M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in roof padding averaging thickness of 50 mm using waterproofing compound as per manufacturer instruction by weight of cemen complete all as specified.(Note : Water proofing compound shall be measured and paid for separately). |
| 126 | M&L for 10 mm thick rendering on fair faces of concrete surfaces in CM 1:4 with water proofing compound as per manufacturer instructions by weight of cement on concrete surface complete all as specified and directed. (Note :- Water proofing compound shall be measured and paid separately). |
| 127 | Supply only integral water proofing compound. |
| 128 | M&L for PCC 1:2:4 type B1 (using 12.5mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 129 | M&L for APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in, including bitumen primer @ 0.40 kg /Sqm after cleaning surface and applying evenly a tack coat of Industrial bitumen 85/25 @ 1.60 Kg per sqm including finishing with two coats of aluminium base paint complete all as specified and as directed. |
| 130 | A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 95,991/- from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit. Please Enable Macros to View BoQ information |
