|
| 1 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep in any type of soil for foundation, laying pipe etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out complete all as specified and directed. |
| 2 | Returning filling in soft/loose soil including spreading levelling watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed. |
| 3 | Removing excavated material (Soils) to a distance not exceeding 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed. |
| 4 | M&L for construction of valve chamber (in replacement) 1200 x 1200 x 1200 mm (internal dimensions), 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in cement mortar (1:6), PCC bed (1:4:8) type D2 (using 40 mm graded crushed stone aggregate) 150 mm thick, cement plastering 15 mm thick in cement mortar (1:4) and applying two coats of synthetic enamel paint over a coat of primer to the steel surfaces including dismantling and removal of old unserviceble valve pit complete all as specified and directed. |
| 5 | All as per Item No 4.00 above but of size 900 x 900 x 900 mm (internal dimension). |
| 6 | M&L for CI fitting (in replacement), like cast iron bends (any type, radius and angle), tapers any type, (straight, bend, increasing, decreasing or double sockets etc.) tee pieces single branch, 'Y' junction, double branch, cross (all socket or spigot and socket) collars, caps and plug upto 150 mm bore for spigot and socket end pipes complete all as specified and directed. |
| 7 | M&L for CI fitting (in replacement) , like cast iron bends (any type, radius and angle), tapers any type, (straight, bend, increasing, decreasing or double sockets etc.) tee pieces single branch, 'Y' junction, double branch, cross (all socket or spigot and socket) collars, caps and plug etc from size 200 mm bore to 300 mm bore for spigot and socket end pipes complete all as specified and directed. |
| 8 | M&L for DI fitting (in replacement), like cast iron bends (any type, radius and angle), tapers any type, (straight, bend, increasing, decreasing or double sockets etc.) tee pieces single branch, 'Y' junction, double branch, cross (all socket or spigot and socket) collars, caps and plug etc from 80 mm bore to 300 mm bore for spigot and socket end pipes complete all as specified and directed. |
| 9 | Taking up or down existing GI tubing and connections including removal to store as sch of credit to contractor for following size of pipes complete all as specified and directed :-(a) 100 mm bore |
| 10 | (b) 80 mm bore |
| 11 | (b) 50 mm bore |
| 12 | (c) 40 mm bore |
| 13 | (d) 25 mm bore |
| 14 | (e) 20 mm bore |
| 15 | (f) 15 mm bore |
| 16 | Supply, fixing, laying & jointing galvanised iron water tubes 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, check nuts, caps, plugs etc.and clips, wall hooks etc. laid in trenches, on ground or fixing on wall and testing complete all as specified and directed of following sizes: -(a) 100 mm bore |
| 17 | (b) 80 mm bore |
| 18 | (c) 50 mm bore |
| 19 | (d) 40 mm bore |
| 20 | (e) 25 mm bore |
| 21 | (f) 20 mm bore |
| 22 | (g) 15 mm bore |
| 23 | Taking up cast iron water main from trenches carefully without any damage (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed for the following sizes:-(a) 200 mm bore |
| 24 | (b) 250 mm bore |
| 25 | Supply, laying and testing of centrifugally cast (Spun) ductile iron pressure pipe Class K-9 with spigot and socket end pipes suitable for tyton joints duly applied with zinc coating with finishing layer of bitumen on external surfaces and cement mortar lining with bituminous seal coat on internal surfaces complete confirming to IS-8329 (2000) including EPDM gaskets, complete all as specified and directed by the Engineer-in Charge of following sizes :- (a) 200 mm boreMake : Electro steel Casting Ltd/TATA Metaliks/ Jindal Ltd / SAW Pipes. |
| 26 | (b) 250 mm bore |
| 27 | Cutting existing CI pipes, laid in position for taking out branch connection by inserting new Tee, branches, coller etc. complete all as specified and directed for the following sizes:- (a) 80 mm bore |
| 28 | (b) 100 mm bore |
| 29 | (c) 150 mm bore |
| 30 | (d) 200 mm bore |
| 31 | (e) 250 mm bore |
| 32 | (d) 300 mm bore |
| 33 | Burning out lead joint and taking out spun yarn carefully for the following sizes of pipes :-(a) 80 mm bore |
| 34 | (b) 100 mm bore |
| 35 | (c) 150 mm bore |
| 36 | (d) 200 mm bore |
| 37 | (e) 250 mm bore |
| 38 | (f) 300 mm bore |
| 39 | M&L for run lead Joint for cast iron pipes spigot and socket ends and cast iron special fitting with caulked spun yarn and lead for following size:-(a) 80 mm bore |
| 40 | (b) 100 mm bore |
| 41 | (c) 150 mm bore |
| 42 | (d) 200 mm bore |
| 43 | (e) 250 mm bore |
| 44 | (f) 300 mm bore |
| 45 | M&L for cutting existing road /floor/plinth of any desription of width not exceeding 750 mm and depth not exceeding 0.45m, including necessary earth work excavation up to 1.00m depth and refilling the same after completion and making good the disturbed road surface with cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) complete all as specified and directed by the Engr-in-Charge. |
| 46 | S&F in replacement gun metal gate or glob valve with iron wheel head, screwed both ends for iron pipe with necessary GI fittings and testing complete including taking out old all as specified and directed of following sizes:-(a) 50 mm bore |
| 47 | (b) 40 mm bore |
| 48 | (c) 25 mm bore |
| 49 | (d) 20 mm bore |
| 50 | (e) 15 mm bore |
| 51 | S&F in replacement Sluice valve cast iron body, double flanged, ISI marked (IS-14846), heavy duty, class PN-1.6 gun metal, with rising spindle of solid forged bronze and operating handle, including rubber gaskets, nuts, bolts, washers etc including taking out old of sluice valve complete of the following sizes :-(a) 80 mm bore |
| 52 | (b) 100 mm bore |
| 53 | (c) 150 mm bore |
| 54 | (d) 200 mm bore |
| 55 | (e) 250 mm bore |
| 56 | (f) 300 mm bore |
| 57 | (g) 400 mm bore |
| 58 | M&L for servicing of sluice valve cast iron body/ Butterfly Valves by greasing/ oiling using T&P as required as per manufacture instructions & providing glands rope of superior quality and rubber gaskets/packing where necessary to stop any leakage of sluice valve of size 80 mm dia to 200 mm dia all as specified and directed. |
| 59 | All as per item No 19.00 above , but for bore size 250 mm to 400 mm dia. |
| 60 | S&F in replacement brass check nut as per existing size including opening head portion of the valve and refixing the same complete suitable for CI Sluice Valve of following sizes :-(a) 80 mm to 200 mm dia |
| 61 | (b) 250 mm to 400 mm dia |
| 62 | S&F in replacement butterfly valve gear operated epoxy coated cast iron body, PN 1.6, ISI marked SGI disc with integral seat of nitrle rubber including taking out old valve, of the following sizes :-(a) 80 mm bore |
| 63 | (b) 100 mm bore |
| 64 | (c) 150 mm bore |
| 65 | (d) 200 mm bore |
| 66 | (e) 250 mm bore |
| 67 | (f) 300 mm bore |
| 68 | (g) 400 mm bore |
| 69 | S&F in replacement air release valve 40 mm double action with two air outlets , ISI marked including jointing materials such as flanges, nuts, bolts, washers, rubber gasket and fixing up in cast iron pipe of any size complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 70 | S&F in replacement air release valve 40 mm double action with two air outlets , ISI marked including jointing materials such as flanges, nuts, bolts, washers, rubber gasket and fixing up in cast iron pipe of any size complete all as specified and as directed. Please Enable Macros to View BoQ information |
