|
| 1 | Supply, installation, testing and commissioning of MNRE approved off Grid Solar Panels for running of motor pumps with 25 years of Linear Generation warranty, Work includes designing of solar panel area and MS frame and foundation on ground/roof of Pump house or CWR, showing arrangement of panel in available space, installation of PV module on MS frame as per approved design and drawings. Mounting structure shall be suitably design to withstand wind velocity up to 150km/hr. The work shall be executed as per detailed technical specifications, approved drawing and direction of Engineer in Charge. Note: There shall be 5 year service warranty for solar panel and mounting structure and suitable provision shall be included in tender document. |
| 2 | Providing, installation, testing and commissioning of AC submerssible pump sets with inbuilt or individual solar pump controller with Maximum power point tracking (MPPT) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day.Solar pump shall be of Stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope .Pump controller shall have Adequate protection against dry operation of motor pump set, and against hails and storms. Full protection against open circuit, accidental short circuit and reverse polarity should be provided. A good reliable on/off switch be provided. The cable shall be ISI marked three core PVC flat submersible cable as per IS 694:1990 or amended up to date ( standard insulation) and conductor as per class 5 of IS 8130:1980 or amended up to date.The duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of Engineer in charge. |
| 3 | 5.5 KW (7.5 HP ) |
| 4 | Supply, installation, testing and commissioning of Remote monitoring unit on off grid solar controller for remote ON/OFF, parameter setting, monitoring and troubleshooting through mobile etc. complete. Web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of Engineer. |
| 5 | Supply & Fixing of ISI marked three core PVC flat submersible cable as per IS 694:1990 or amended up to date and conductor as per class 5 of IS 8130:1980 including making connection etc. 3 core 6 mm2 |
| 6 | Providing & Lowering in tubewell ISI marked GI Pipe “B\\" class as per IS:1239 or amended up to date threaded and double flanged (welded) on both ends and two number 25x3mm flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect.50 mm dia |
| 7 | Supply & Fixing M S clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. |
| 8 | 180 Cm. high fencing with angle iron post 55x55x6mm placed at every 3 Mtr. apart 45Cm. in ground embedded in cement concrete 1:3:6 (30x30x60 Cm.) corner and every tenth post to be strutted with 55x55x6mm. angle iron provided with 6 horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with G.I. staples including earth work in excavation etc. complete. |
| 9 | Earthwork in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms,lift upto 1.5 Mtr. Including taking out the excavated soil and depositing and refilling of Jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 Mtrs. All Kinds of soils |
| 10 | Providing and laying cement concrete including curing compacting etc complete, using stone aggregate of 20 mm Nominal size in foundation plinth , excluding the cost of shuttering using (M-10 Grade 1:3:6) [1 Cement : 3 coarse Sand : 6 Grade Stone Aggregate] |
| 11 | Providing and laying cement concrete including curing compacting etc complete, using stone aggregate of 20 mm Nominal size in foundation plinth , excluding the cost of shuttering using (M-15) Grade Mix 1:2:4[1 Cement : 2 coarse Sand : 4 Grade Stone Aggregate] |
| 12 | Providing and laying in position specified grade of cementconcrete for all RCC structural elements upto plinth levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.M20 grade Nominal Mix / Design Mix |
| 13 | 4.6.1 Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix. |
| 14 | Centering and shuttering with plywood or steel sheet including strutting , propping , bracing bothway and removal of formwork for foundation in basement raft , footing ,strap beams , bases of columns , etc. upto plinth level |
| 15 | Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for :Walls (any thickness) including attached pilasters,buttresses plinth and string course. |
| 16 | Add extra for shuttering in circular work (in respectivecentering and shuttering items) |
| 17 | Providing and fabricating reinforcement for R.C.C. workincluding straightening, cutting, bending, placing in positionand binding (including cost of binding wire) all complete up tofloor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IScode) |
| 18 | P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. |
| 19 | 50 mm nominal bore |
| 20 | Providing, lowering, laying and jointing in trenches, standard lengths HDPE ISI marked Pipes as per IS-4984: 1995 (amended upto date) with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe by electro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (Tee, bend etc.), satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of Engineer-in-charge of following class and diameter. (excluding earth work) . Note : Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately.Supply may be in coil or straight length in 6 M/12 M. |
| 21 | 90 mm HDPE (PE-80 PN-6) For connection of tubewell |
| 22 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in trenches for water supply pipe lines, shoring and strutting if required as per required gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site etc. complete for lifts up to 1.5 depth and strata as specified. The work also includes depositing and refilling of trench with watering & ramming /compacting in layers and disposal of surplus excavated soil as directed for lead up to 50 mtr. |
| 23 | In all type of soil |
| 24 | For HDPE pipe line |
| 25 | Providing, lowering, aligning, fixing in position in pipe line, CI D/F Sluice valves of approved make of following Pressure rating & dia complete, confirming to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/ FG200 Stem - SS 304 ,Body Seat ring, Wedge facing ring & Bushes - LTB2/ SS , Face to face dimensions as per IS 14846/2000 (amended up to date), All exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to IS:5660 and two coats of black Japan paint conforming toType B of IS 341or paint conforming to IS9862 or IS2932( Non-Toxic- suitable for drinking water) applied inside and outside, Flanges Drilled as per IS 1538.Nut-Bolt confirming to IS:1363 and IS: 1367/ CS/ galvanised steel.Insersion rubber of black EPDM 6mm thick . Suitable support structure as per directions of EIC. Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge. (80 MM dia)Note: Rates are exclusive of tail piece/ dismantling joints and earth work. |
| 26 | Manually Operated CI Sluice valve of Class PN-1.0 |
| 27 | 80 mm HW Please Enable Macros to View BoQ information |
