|
| 1 | Supply, installation, erection, testing, and commissioning of pumpsets and allied works |
| 2 | 1.01 Supply, Installation, Erection, Testing, Commissioning and fitting charges for all accessories of horizontally mounted submerged Centrifugal Non clog pump set of Compact Unitary Mono-block submerged Single/multi stage, Volute type casing with suitable radial type impellers on common shaft for pump and motor ,Anti friction bearing with life time greasing, protection features with sensors to monitor temperature, Mechanical seal leakage ,etc.(The pump should be confirming to HIS/IS standards).The MOC of pump, casing-cast iron, impeller -SS CF8M,Shaft-SS-316,Suction Strainer -SS and other as per IS standard. The motor should be suitable for 3 Phase,415V /-10%,50Hz /- 5%,AC supply submersible motor having Class F /H insulation, Air filled and IP-68protection confirming to IS 325 or latest standards suitable for day night operation. The pump discharge capacity of 200 cubic metre /hour against duty point head of 48 mtrs, Working Head Range 22 - 56m, Speed 1450RPM(N) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. The pump should be painted with three coats of suitable anti corrosive paint over priming coat. The electrical works for the pumpset should be completed as per KSEB Rules and Regulations and the contractor is responsible for arranging permissions and certificates from the electrical inspectorate. The suction side of the pumpset should be provided with an additional Steel grill for preventing foreign particles inside the inlet side of the pump casing. - 1 Nos, 1.02 Supply and erection of 60HP Auto Transformer starter (ATS) with suitable incomer and contactors including 24 KVAR Capacitor with required indications ,metering and protections for single phasing ,overload, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board - 1 Nos,1.03 Supply and laying additional termination cable of 1.1Kv 3.5 core 95sqmm Aluminium conductor XLPE insulated ;steel armoured UG cable as per relevant IS 7098 with support for cable - 40 metre,1.04 Providing earthing as per the ISI specification with earth electrode of 2.10m class be GI pipe of dia not less than 40mm with necessary funnelling arrangement with necessary masonry work and 38mm RCC cover slab for brick masonry - 4 each,1.05 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. - 2462.37 kg, supported with suitable concrete foundation.1.06 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 250 mm diameter Class II - 1 Nos,1.07 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 200 mm diameter Class II - 1 Nos,1.08 MS Pipes 200mm - Manufacturing supplying and fitting 200mm dia MS pipe of various length with shell thickness 8mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site. - 30 metre,1.09 MS Flanges for 200mm pipe - Manufacturing supplying and fitting 200 mm dia MS Flange having shell thickness 10mm depth 60mm with suitable bolt holes fixing the flange in position with required welding around the flange pipe joint grinding for smoothing the welded portion, including painting with red oxide primer etc. complete as directed by departments officers. - 16 joint,1.10 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 200 mm diameter Class II - 1 Nos,1.11 Supplying and fixing Pressure Gauge 0-16 kg/cm2 with psi 160mm Dia, Bottom Mounting, 1/2 '' BSP, Case: SS with Case vent, Window: Safety Glass, Dial: White Aluminium, Pointer: Black Aluminium, Dry Case, Accuracy: 1 % of FS.Units/Pkg: 1 to the delivery line of pumpsets - 1 Nos,1.12 Providing and fixing MS bolts including nuts and washers with Two coats of priming coat complete . - 69 kg,1.13 Supplying 2 Ton Chain pully unit for lifting submersible motor pumpset - 1 Nos,1.14 Supplying 20mm steel rope for lifting pumpset - 30 metre,1.15 Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work - 102.259 sqm,1.16 Suitable Mobi Start arrangement for pumpset- 1 Nos,1.17 KSEB Service Connection Charges to Punchavayal Pump House - 1 Nos |
| 3 | 2.01 Supply, Installation, Erection, Testing, Commissioning and fitting charges for all accessories of horizontzlly mounted submerged Centrifugal Non clog pump set of Compact Unitary Mono-block submerged Single/multi stage, Volute type casing with suitable radial type impellers on common shaft for pump and motor ,Anti friction bearing with life time greasing, protection features with sensors to monitor temperature, Mechanical seal leakage ,etc.(The pump should be confirming to HIS/IS standards).The MOC of pump, casing-cast iron, impeller -SS CF8M,Shaft-SS-316,Suction Strainer -SS and other as per IS standard. The motor should be suitable for 3 Phase,415V /-10%,50Hz /- 5%,AC supply submersible motor having Class F /H insulation, Air filled and IP-68protection confirming to IS 325 or latest standards suitable for day night operation. The pump discharge capacity of 160 cubic metre /hour against duty point head of 40 mtrs, Working Head Range 22 - 47m, Speed 1450 RPM(N) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. The pump should be painted with three coats of suitable anti corrosive paint over priming coat. The electrical works for the pumpset should be completed as per KSEB Rules and Regulations and the contractor is responsible for arranging permissions and certificates from the electrical inspectorate. The suction side of the pumpset should be provided with an additional Steel grill for preventing foreign particles inside the inlet side of the pump casing. - 1 nos, 2.02 Supply and erection of 40HP Auto Transformer starter (ATS) with suitable incomer and contactors including 16 KVAR Capacitor with required indications ,metering and protections for single phasing ,over load, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board - 1 Nos,2.03 Supply and laying additional termination cable of 1.1Kv 3.5 core 70sqmm Aluminium conductor XLPE insulated ;steel armoured UG cable as per relevant IS 7098 with support for cable - 60 metre,2.04 Providing earthing as per the ISI specification with earth electrode of 2.10m class be GI pipe of dia not less than 40mm with necessary funnelling arrangement with necessary masonry work and 38mm RCC cover slab for brick masonry - 4 each,2.05 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. - 984.95 kg, supported with suitable concrete foundation.2.06 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 250 mm diameter Class II - 1 Nos,2.07 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 200 mm diameter Class II - 1 Nos,2.08 MS Pipes 150mm - Manufacturing supplying and fitting 150mm dia MS pipe of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site. - 20 metre,2.09 MS Flanges for 150mm pipe - Manufacturing supplying and fitting 150mm dia MS Flange having shell thickness 10mm depth 75mm with suitable bolt, holes, fixing the flange in position with required welding around the flange, pipe joint grinding for smoothing the welded portion including painting with red oxide primer etc. complete as directed by departments officers. - 16 joint,2.10 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 150 mm diameter Class II - 1 Nos,2.11 Supplying and fixing Pressure Gauge 0-16 kg/cm2 with psi 160mm Dia, Bottom Mounting, 1/2 '' BSP, Case: SS with Case vent, Window: Safety Glass, Dial: White Aluminium, Pointer: Black Aluminium, Dry Case, Accuracy: 1 % of FS.Units/Pkg: 1 to the delivery line of pumpsets - 1 Nos,2.12 Providing and fixing MS bolts including nuts and washers with Two coats of priming coat complete . - 46 kg,2.13 Supplying 2 Ton Chain pully unit for lifting submersible motor pumpset - 1 Nos,2.14 Supplying 20mm steel rope for lifting pumpset - 20 metre,2.15 Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work - 40.903 sqm,2.16 Suitable Mobi Start arrangement for pumpset- 1 Nos,2.17 KSEB Service Connection Charges to Manikkuni Pump House - 1 Nos |
| 4 | 3.01 Supply, Installation, Erection, Testing, Commissioning and fitting charges for all accessories of horizontally mounted submerged Centrifugal Non clog pump set of Compact Unitary Mono-block submerged Single/multi stage, Volute type casing with suitable radial type impellers on common shaft for pump and motor ,Anti friction bearing with life time greasing, protection features with sensors to monitor temperature, Mechanical seal leakage ,etc.(The pump should be confirming to HIS/IS standards).The MOC of pump, casing-cast iron, impeller -SS CF8M,Shaft-SS-316,Suction Strainer -SS and other as per IS standard. The motor should be suitable for 3 Phase,415V /-10%,50Hz /- 5%,AC supply submersible motor having Class9;F39;/H insulation, Air filled and IP-68protection confirming to IS 325 or latest standards suitable for day night operation. The pump discharge capacity of 185 cubic metre /hour against duty point head of 24 mtrs, Working Head Range 18 - 34m, Speed 1450RPM(N) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. The pump should be painted with three coats of suitable anti corrosive paint over priming coat. The electrical works for the pumpset should be completed as per KSEB Rules and Regulations and the contractor is responsible for arranging permissions and certificates from the electrical inspectorate. The suction side of the pumpset should be provided with an additional Steel grill for preventing foreign particles inside the inlet side of the pump casing. - 1 Nos, 3.02 Supply and erection of 30HP Auto Transformer starter (ATS) with suitable incomer and contactors including 12.5 KVA Capacitor with required indications ,metering and protections for single phasing ,over load, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board - 1 Nos,3.03 Supply and laying additional termination cable of 1.1Kv 3.5 core 50sqmm Aluminium conductor XLPE insulated ;steel armoured UG cable as per relevant IS 7098 with support for cable - 40 metre,3.04 Providing earthing as per the ISI specification with earth electrode of 2.10m class be GI pipe of dia not less than 40mm with necessary funnelling arrangement with necessary masonry work and 38mm RCC cover slab for brick masonry - 4 each,3.05 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. - 2462.37 kg, supported with suitable concrete foundation.3.06 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 150 mm diameter Class II - 1 Nos,3.07 MS Pipes 150mm - Manufacturing supplying and fitting 150mm dia MS pipe of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site. - 35 metre, 1.26 MS Flanges for 150mm pipe – Manufacturing supplying and fitting 150mm dia MS Flange having shell thickness 10mm depth 75mm with suitable bolt, holes, fixing the flange in position with required welding around the flange, pipe joint grinding for smoothing the welded portion including painting with red oxide primer etc. complete as directed by departments officers. - 18 joint, 1.29 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 150 mm diameter Class II - 1 Nos,3.08 Supplying and fixing Pressure Gauge 0-16 kg/cm2 with psi 160mm Dia, Bottom Mounting, 1/2 '' BSP, Case: SS with Case vent, Window: Safety Glass, Dial: White Aluminium, Pointer: Black Aluminium, Dry Case, Accuracy: 1 % of FS.Units/Pkg: 1 to the delivery line of pumpsets - 1 Nos,3.09 Providing and fixing MS bolts including nuts and washers with Two coats of priming coat complete . - 34 kg,3.10 Supplying 2 Ton Chain pully unit for lifting submersible motor pumpset - 1 Nos,3.11 Supplying 20mm steel rope for lifting pumpset - 30 metre,3.12 Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work - 102.258 sqm,3.13 Suitable Mobi Start arrangement for pumpset- 1 Nos,3.14 KSEB Service Connection Charges to Kolembetta Pump House - 1 Nos |
| 5 | 4.01 Supply, Installation, Erection, Testing, Commissioning and fitting charges for all accessories of horizontally mounted submerged Centrifugal Non clog pump set of Compact Unitary Mono-block submerged Single/multi stage, Volute type casing with suitable radial type impellers on common shaft for pump and motor ,Anti friction bearing with life time greasing, protection features with sensors to monitor temperature, Mechanical seal leakage ,etc.(The pump should be confirming to HIS/IS standards).The MOC of pump, casing-cast iron, impeller -SS CF8M,Shaft-SS-316,Suction Strainer -SS and other as per IS standard. The motor should be suitable for 3 Phase,415V /-10%,50Hz /- 5%,AC supply submersible motor having Class F /H insulation, Air filled and IP-68protection confirming to IS 325 or latest standards suitable for day night operation. The pump discharge capacity of 155 cubic metre /hour against duty point head of 22 mtrs, Working Head Range 13 - 27m, Speed 1450 RPM(N) or nearer, with 10meters of copper power cable and control cable, railing arrangement. The pump should be painted with three coats of suitable anti corrosive paint over priming coat. The electrical works for the pumpset should be completed as per KSEB Rules and Regulations and the contractor is responsible for arranging permissions and certificates from the electrical inspectorate. The suction side of the pumpset should be provided with an additional Steel grill for preventing foreign particles inside the inlet side of the pump casing. - 1 Nos, 4.02 Supply and erection of 25HP Auto Transformer starter (ATS) with suitable incomer and contactors including 10 KVAR Capacitor with required indications ,metering and protections for single phasing ,over load, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board - 1 Nos,4.03 Supply and laying additional termination cable of 1.1Kv 3.5 core 35sqmm Aluminium conductor XLPE insulated ;steel armoured UG cable as per relevant IS 7098 with support for cable - 20 metre,4.04 Providing earthing as per the ISI specification with earth electrode of 2.10m class be GI pipe of dia not less than 40mm with necessary funnelling arrangement with necessary masonry work and 38mm RCC cover slab for brick masonry - 4 each,4.05 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. - 344.73 kg, supported with suitable concrete foundation.4.06 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 150 mm diameter Class II - 1 Nos,4.07 Providing and fixing C.I. Non Return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 125 mm diameter Class II - 1 Nos,4.08 MS Pipes 125mm - Manufacturing supplying and fitting 125mm dia MS pipe of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site - 15 metre,4.09 MS Flanges for 125mm pipe – Manufacturing supplying and fitting 125 mm dia MS Flange having shell thickness 10mm depth 60mm with suitable bolt holes fixing the flange in position with required welding around the flange pipe joint grinding for smoothing the welded portion, including painting with red oxide primer etc. complete as directed by departments officers. - 16 joint,4.10 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 125 mm diameter Class II - 1 Nos,4.11 Supplying and fixing Pressure Gauge 0-16 kg/cm2 with psi 160mm Dia, Bottom Mounting, 1/2 '' BSP, Case: SS with Case vent, Window: Safety Glass, Dial: White Aluminium, Pointer: Black Aluminium, Dry Case, Accuracy: 1 % of FS.Units/Pkg: 1 to the delivery line of pumpsets - 1 Nos,4.12 Providing and fixing MS bolts including nuts and washers with Two coats of priming coat complete . - 29 kg,4.13 Supplying 2 Ton Chain pully unit for lifting submersible motor pumpset - 1 Nos,4.14 Supplying 20mm steel rope for lifting pumpset - 10 metre,4.15 Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work - 14.316 sqm,4.16 Suitable Mobi Start arrangement for pumpset- 1 Nos,4.17 KSEB Service Connection Charges to Valiyavattam Pump House - 1 Nos |
| 6 | 5.01 Supply, Installation, Erection, Testing, Commissioning and fitting charges for all accessories of horizontally mounted submerged Centrifugal Non clog pump set of Compact Unitary Mono-block submerged Single/multi stage, Volute type casing with suitable radial type impellers on common shaft for pump and motor ,Anti friction bearing with life time greasing, protection features with sensors to monitor temperature, Mechanical seal leakage ,etc.(The pump should be confirming to HIS/IS standards).The MOC of pump, casing-cast iron, impeller -SS CF8M,Shaft-SS-316,Suction Strainer -SS and other as per IS standard. The motor should be suitable for 3 Phase,415V /-10%,50Hz /- 5%,AC supply submersible motor having Class F /H insulation, Air filled and IP-68protection confirming to IS 325 or latest standards suitable for day night operation. The pump discharge capacity of 125 cubic metre /hour against duty point head of 26 mtrs, Working Head Range 16 - 32m, Speed 1450 RPM(N) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. The pump should be painted with three coats of suitable anti corrosive paint over priming coat. The electrical works for the pumpset should be completed as per KSEB Rules and Regulations and the contractor is responsible for arranging permissions and certificates from the electrical inspectorate. The suction side of the pumpset should be provided with an additional Steel grill for preventing foreign particles inside the inlet side of the pump casing. - 1 Nos, 5.02 Supply and erection of 20HP Auto Transformer starter (ATS) with suitable incomer and contactors including 8 KVAR Capacitor with required indications ,metering and protections for single phasing ,over load, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board - 1 Nos, 5.03 Supply and laying additional termination cable of 1.1Kv 3.5 core 35 sqmm Aluminium conductor XLPE insulated ;steel armoured UG cable as per relevant IS 7098 with support for cable - 50 metre,5.04 Providing earthing as per the ISI specification with earth electrode of 2.10m class be GI pipe of dia not less than 40mm with necessary funnelling arrangement with necessary masonry work and 38mm RCC cover slab for brick masonry - 4 each,5.05 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. - 344.73 kg, supported with suitable concrete foundation.5.06 Providing and fixing C.I. Non return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 200 mm diameter Class II - 1 Nos,5.07 Providing and fixing C.I. Non Return valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 125 mm diameter Class II - 1 Nos,5.08 MS Pipes 125mm - Manufacturing supplying and fitting 125mm dia MS pipe of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site - 15 metre,5.09 MS Flanges for 125mm pipe – Manufacturing supplying and fitting 125 mm dia MS Flange having shell thickness 10mm depth 60mm with suitable bolt holes fixing the flange in position with required welding around the flange pipe joint grinding for smoothing the welded portion, including painting with red oxide primer etc. complete as directed by departments officers. - 18 joint,5.10 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 125 mm diameter Class II - 1 Nos,5.11 Supplying and fixing Pressure Gauge 0-16 kg/cm2 with psi 160mm Dia, Bottom Mounting, 1/2 '' BSP, Case: SS with Case vent, Window: Safety Glass, Dial: White Aluminium, Pointer: Black Aluminium, Dry Case, Accuracy: 1 % of FS.Units/Pkg: 1 to the delivery line of pumpsets - 1 Nos,5.12 Providing and fixing MS bolts including nuts and washers with Two coats of priming coat complete . - 23 kg,5.13 Supplying 2 Ton Chain pully unit for lifting submersible motor pumpset - 1 Nos,5.14 Supplying 20mm steel rope for lifting pumpset - 10 metre,5.15 Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work - 14.316 sqm,5.16 Suitable Mobi Start arrangement for pumpset- 1 Nos,5.17 KSEB Service Connection Charges to Padiyeri Pump House - 1 Nos Please Enable Macros to View BoQ information |
