|
| 1 | (G Schedule Amount) Please Fill BOQ2 Total Amount |
| 2 | (H Schedule Amount) Please Fill BOQ3 Total Amount |
| 3 | Providing & laying P.V.C. / XLPE insulated & P.V.C. sheathed Arroured Aluminium cable confirming to IS : 1554 P-I/IS : 7098 P-I of 1.1 KV with H4-Grade electrolytic aluminium conductor confirming to IS 8130of purity >99.6% round/flat strip armouring of cables, Inner/Outer sheath confirming to IS: 5831 in existing RCC/Hume stoneware/PVC pipe/open duct/cable trench/cable tray (with cable tie) including testing etc. as required of following size OEM must have it's own in house NABL accrediated laboratory for testing procedure as per IS: 10810. for additional technical parameters of product work refer annexure. 'A' attached with this BSR 10 Sq mm2 core |
| 4 | Supplying and drawing FR PVC insulated & Unsheathed flexible copper conductor as per PWD specification for electrical works with isi marked (IS:694) and as per IS 8130:2013 of 1.1 KV grade. Wire should be made from 99.90% Purity copper, class 5 stranding in acc. to IS: 8130/IEC 60228 for lower watt loss, oxygen free for less chances of oxidization insulation PVC type A/C/D flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with copper lugs of suitable size. Ferrules, testing etc. as required OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product/ work refer annexure 'A' attached with this BSR. 3 x 2.5 sq.mm |
| 5 | S&F follwing sizes (dia) of ISI marked virgin material MMS (IS: 9537 P-III) PVC conduit along with ISI Marked (IS: 3419-1988) accessories as required in recess including cutting the well, covering conduit and making good the same as required. For additional technical parameters of product/work refer Annexure 'A' attached with this BSR. 25mm |
| 6 | Decorative haritage pole in 4 Meter height. Pole upper section of length 3mtr is of dia 76mm and 1 meter bottom section of dia 114mm with decorative casting with base plate as per drawing. Provision for inside termination box with 4way connector & 1nos 6 AMPS MCB for local isolation with cover.Complete in all aspects with foundation bolts. |
| 7 | Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressure diecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beam angles, of high power LED of 3 to 5 watt each. Integrated potted driver as a unique BIS R number having efficiency more than 85% and in compliance to BIS certified and Trade mark certificate. The System level Luminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety .Power Factor >0.95 THD(I) <10%, driver current <=750mA. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector, Surge Protection Min >-4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hours with 70% of Initial Lumens maintained, CRI>70 and CCT 5700K ±355K. Manufactures Word Mark/Name Engraved/Embossing /Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. refer Annexure \\"A\\" attached with this BSR. High Power LED Flood Light Minimum lumen output 6200 Im Note: The colour of the flood light will be as per site requirement as pre approved by Engineer in charge. |
| 8 | Supplying, erecting and fixing in position specified precast RCC bench made of RCC grade M-30 consisting of 2 Nos. “L” shaped base support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in-charge. Every bench should have a manufacturer’s logo of appropriate size Engraved at suitable place. |
| 9 | P/F IP-65/IP-66 protected heritage look or ornamental cast iron deocorative light height 609mm and with polycarbonate acrylic side cover of Warm White 20 W LED-24 watt LED light or any other colour with polycorbonate cover as per site requirement as per approved by engineer in charge on existing bracket as per approved drawing and design. Approved by Engineer |
| 10 | Supply and fixing of round LED Rope/neon flex LED/Flexible strip type LED outdoor weaterproof Waterproof with IP65 rating, for superior life and withstanding harsh weather. Flexible, Slim & Compact. Applicable for bendable or angled patterns, or in continuous rows. Easy to form into any shape you want, adaptable to various places and locations. round LED Rope/neon flex LED/Flexible strip type LED having 3 to 6 watts/meter capacity and consisting suitable power adapter and driver complete with connection to operate system as and when etc as required. Colour of the rope light should be preferably yellow/ orange to be approved by Engineer incharge. All as per pre approved by Engineer incharge. Make Philips. Thaiai winro HPI, वल्स |
| 11 | P/F IP-65/ IP-66 protected facade light luminaries în up down pattern or any other pattern light as per site reqiurement of Warm White or any other colour light as per direction of engineer incharge 10 W to 12 watt LED to highlight particular object as per site requirement as per approved by engineer in charge as per approved drawing and design. Please Enable Macros to View BoQ information |
