|
| 1 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified. |
| 2 | M&L hardcore of gauge not exceeding 63 mm,Broken below sub base /plinth protection hard standing complete all as specified and directed. |
| 3 | M&L Broken stone or boulders hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 4 | M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in fdn filling mass concrete complete all as specified. |
| 5 | M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in fdn filling mass concrete complete all as specified. |
| 6 | M&L PCC 1:3:6 type C2 using 40mm graded stone aggregate as in fdn filling mass concrete complete all as specified. |
| 7 | M&L for forming embarkment including raising (or lowering ) earth spreading in layer n.exc. 30cm thick watering , ramming / rolling and finishing to requried size and slope etc n. exc 1.5 mtr high from base concrete complete all as specified. |
| 8 | M&L forgrit/sand cushioning below interlocking paver block inc spreading and levelling complete all as specified and directed. |
| 9 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc and getting out in soft/loose soil etc complete all as specified and directed |
| 10 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth under ground cable and pipe and getting out in hard/dense soil etc complete all as specified and directed |
| 11 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation n. exc. 10sqm on plan and getting out in soft/loose soil etc complete all as specified and directed |
| 12 | Excavation over area not exceeding 1.5m deep and getting out in soft/loose soil etc complete all as specified and directed |
| 13 | Rough Excavation not exceeding 1.5m deep and getting out in any typr of soil complete all as specified and directed |
| 14 | M&L for sand filling under floor or in foundation including watering and cconsolidating complete all as specified & directed. |
| 15 | M&L for Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified & directed. |
| 16 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), complete all as specified and as directed. |
| 17 | S&F factory made soild PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelam sheet as per specification and drawing given on MES schedule Part-II (2020) complete all as specified and directed. |
| 18 | S&F Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with particle board core, supplying & fixing in frame at site complete all as specified and as directed |
| 19 | S & F new 1 X 20W, 4 feet, LED light fittings wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation and integrated electric driver including 1 x 20 Watt LED Tube light etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size compete all as specified and directed. |
| 20 | Supply, installation, testing, commissioning of high mast complete motorized alongwith wiring from MCB to flood light fittings, foundation, excavation, return filling, RCC/PCC including form work, foundation bolts, nuts, washers, anchor plate and template etc as per following specifications :- (a) General specifications (i) Height of mast - 15 mtrs, (ii) Material of construction : BS EN 10025/IS 2062, (iii) Thickness of material - Top section 3mm, bottom section 4mm, (iv) Cross section of mast (number of sides)-20 sided polygon, (v) Length of individual section - Top sec : 8.35 mtrs, Bottom sec : 8.35mtrs, (vi) Diameter - Base dia : 460mm, top dia : 150mm, (vii) Types of joints - stress slip fit joints. (viii) Length of overlap-1.5 times the dia of intersection, (ix) Metal protection treatment - Hot dip galvanised as per IS 4759/IS 2629, (x) Thickness of galvanisation - average 70 microns, (xi) Size of door opening at base of mast - 1200mmx 300mm, (xii) Types of locking on door panel - Close fitting door with allen key locking with suitable reinforcement to avoid buckling at base of mast. (xiii) Lightening protection finial - GI single spike of length 1200mm, (xiv) Size of base plate - Dia : 670mm, Thickness : 30mm, (b) Dynamic loading as prevailing at site (i) Max wind speed : 180 Km/hr, (ii) Number of foundation bolts - 08 Nos, (iii) PCD of foundation bolts - 590mm,(iv) Dia of foundation bolts - M30, (v) Length of foundation bolts - 850mm (c) Lantern Carriage (i) Material of construction - 40 NB /ERW CKASS B-MS PIPE, (ii) Dia of lantern carriage ring-800mm (ID), (iii) Construction - 8 arms welded, (iv) Number of joints - 2 segments, (v) Load carrying capacity - 9 luminaries, symmerical |
| 21 | (d) Winch : (i) Number of drums per winch- double drum, (ii) Gear Ratio - 50:1, (iii) Capacity - SWL750 Kgs, (iv) Method of operation - Motor or manual, (v) Lubrication arrangements - Self Lubricating in permanent oil bath, (vi) Type of lubricant - SAE 90/140 (e) Stainless steel wire rope (i) Grade - AISI 316, (ii) Dia of SS rope - 6mm, (iii) Construction of SS Rope - 7/19, (iv) Number of SS Ropes - 03 Nos of 6mm for lantern carriage, 02 Nos of 6mm for double drum winch, (v) Thimbles and terminals - Provided, (vi) Breaking load capacity - 2350 Kgs per SS wire rope.(f) Trailing cable (i) Type - Flexible copper 5 core 2.5 sqmm FRLSH 02 Nos, (ii) Material - EPR insulated PCP sheathed/PVC, (iii) Make - IS approved, (iv) No of circuits per mast - Two(g) Power tool (i) Model - Integral, (ii) Capacity (HP) - 1.5 HP, (iii) Number of speed - Single speed, (iv) Reversible / non reversible - Reversible, (v) Input supply - 415 Volts/240 Volts, (vi) Torque limitor - Withmechanical trippping facility.(h) Aviation light :-LED aviation light 6W luminaries integral LED light comprising of polycarbonate enclosure alongwith suitable fixing arrangements with rolled steel equal angle of 25 x 25 mm for making structure suitable for aviation obstruction light including welding, bending cold/hot drilled holes for nuts, bolts and washers of any shape or size as required base all as speficied and directed by Engr-in-Charge.Note :- Cost of Excavation, return filling, PCC/RCC inclduing form work, foundation bolts, nuts, washers, anchor plate, and template all as per manufacture drawing complete all as specified and directed and no extra cost will be deemed to be included in the item rate and no extra will be paid to the contractor. |
| 22 | Supply and fixing of LED flood light fitting of capacity 200 Watt in aluminium housing with LED lamp, toughened glass cover with IP66 protection with 4/5 KV inbuilt surge protector and cable connection from looping box to light fitting at any height and testing after and including taking down existing unserviceable fittings complete all as specified and directed . |
| 23 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics including brackets for fixing complete with IP 65/66 protection complete all as specified and directed. |
| 24 | Supply and fixing of exhaust fan steel body AC 230 volts 300 mm sweep, with blades and frame and louvers including making holes in wall floors etc. |
| 25 | Supply, installation, testing & commissioning of totally enclosed feeder pillar outdoor type fabricated out of 3.15 mm thick CRCA sheet dust and vermin proof powder coated double door type (independent cabin including locking arrangement for each MCBs, bus bar chamber enclosed complete suitable for operating on 415 Volt 50 Hz AC supply internally wired with copper conductor having legs 75 cms made out of 40x40x4 mm angle iron grouted on brick masonary platform upto 30 cms. Brick masonary platform should be 60 cms above the Ground Level. Comprising the following:- .Note:- (i) The panel shall be front operated with cable entry from the bottom with cable glands. Earth bus shall be part of the main feeder pillar. (ii) Fabrication of feeder pillar box to be approved by CPRI width of the panel not less than 45 cms. (iii) Cost for construction of platform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 including plaster work, PCC copping 1:2:4 (40 mm thick stone aggerate), deemed to be included in the item rate. No Extra payment will be made. (iv) MCB's should be connected with extensions terminals at both side (incoming and outgoing). |
| 26 | (a) 01 set of 100 Amps TPN aluminium bus bar of suitable length and of crossection as per design with colour codding. Bus bars shall be designed to with stand a fault level of 16 KA at 415 volts.(b) Supply and fixing MCB TPN 40 Amp 10 KA, Makes : Legrand /Schneider/Siemens -01 No as incoming(c) Supply and fixing MCB TPN 20 Amp 10 KA, Makes : Legrand /Schneider/Siemens -01 No as outgoing(d) MCB SP, 6 Amps 240 Volts AC 10KA - 04 Nos. Make :- Legrand/Schneider/Seimens(e) Automatic street light switch :- Make : Healer enterprises Model No SWADEEP 02EC5KW3P. (f) Digital type amp meter 0-500Amp with CT’s & selector switch - 01 No. (g) LED Indicating lamp (RYB-one set) (h) Digital voltmeter 0-500 volts with selector switch |
| 27 | M & L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR Part-I including excavation and earthwork in any type of soil / strata and testing on completion. Note:- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted. |
| 28 | Supply and lay cable XLPE insulated screened PVC bedded,galvanised steel strip or wire armoured electric power cable (heavy duty)1100 volt grade with stranded aluminium conductor of size 16 sq mm 4 core complete. |
| 29 | Supply and lay cable XLPE insulated screened PVC bedded,galvanised steel strip or wire armoured electric power cable (heavy duty)1100 volt grade with stranded aluminium conductor of size 25 sq mm 4 core complete. |
| 30 | Supply and lay underground LT cable 1100 volt grade heavy duty electric cable XLPE insulated & PVC outer sheathing withaluminium conductor armoured cable 10sq mm 2 corecable confirming to IS -7098 Part-I (1988) with lastest ammendments of size:- |
| 31 | Supply and lay cable XLPE insulated screened PVC bedded,galvanised steel strip or wire armoured electric power cable (heavy duty)1100 volt grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete. |
| 32 | M & L for unreinforced precasted concrete cable cover class LV, type 1,flat , size 250mm x 150mm x 40mm complete. |
| 33 | Supply and spreading dry river sand in trenches for cushioning of cable 8 cm layer before laying the cable and 15cm thick layer after laying the cable. Note-Sand layer shall be paid for 18mm only after well pressed complete. |
| 34 | Supply, installation, testing & commissioning in renewal of totally enclosed feeder pillar outdoor type fabricated out of 3.15 mm thick CRCA sheet dust and vermin proof powder coated double door type (independent cabin including locking arrangement for each MCCBs, bus bar chamber enclosed and 500 Amp rated bus bar TPN complete suitable for operating on 415 Volt 50 Hz AC supply internally wired with copper conductor having legs 90 cms made out of 50x50x6 mm angle iron grouted on brick masonary platform upto 45 cms. Brick masonary platform should be 60 cms above the Ground Level. Comprising the following:- Note:- (i) The panel shall be front operated with cable entry from the bottom with cable glands. Earth bus shall be part of the main feeder pillar. (ii) Fabrication of feeder pillar box to be approved by CPRI width of the panel not less than 75 cms. (iii) Cost for construction of platform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 including plaster work, PCC copping 1:2:4 (40 mm thick stone aggerate), deemed to be included in the item rate. No Extra payment will be made. (iv) MCCB's should be connected with extensions terminals at both side (incoming and outgoing) |
| 35 | (a) INCOMING(i) MCCB 4 Pole 415 volts grade 350 Amps rating and 16 KA rupturing capacity -01 No(ii) Voltmeter 0-500 volts, Square 96 mm, flnsh pattern with 3 way rotary selector switch-01 No(iii) Ammeter size 96 mm, square dial flush pattern having dual range 500 Amps with three way rotary selector switch -01 No(iv) CTs ratio 160/5 class ISI marked sets of three each(v) Indicating lamp-01 set of three(b) OUTGOING(i) MCCB 415 volts grade 125 Amps rating and 16 KA rupturing capacity -04 Nos (ii) MCCB 415 volts grade 63 Amps rating and 16 KA rupturing capacity -02Nos (iii) MCB SPN 32 Amps 10KA - 02 Nos |
| 36 | Supply and fixing of Gun metal gate valve ISI marked with iron wheel head screwed both ends for pipe of size 20mm complete all as specified and as directed |
| 37 | Supply and fix in repair bevelled edge mirror 5.0mm thick selected quality glass, 600mm x 450 mm size, mounted on 6 mm thick AC building board or commercial plywood with aluminium angle bead alround the mirror and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified & directed. |
| 38 | Supply and fix, in repair, 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including complete all as specified & directed. |
| 39 | Supply and fix, in repair, 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including complete all as specified & directed. |
| 40 | Supply and fixing distribution board,(SPN) single door 4 way, and should be IP 43 Ip protected with copper conductor bus bar 100Amp rated , earth bar , neutral bar dooe earthing complete all as specified and directed. |
| 41 | Supply and fixing MCB SPN complete 32 amps, with 240 volts rupturing capacity 10 KA 'C' series complete all as specified and directed. |
| 42 | Supply and fixing of MCB single pole & neutral 240 volts , 6 to 32 amps, with rupturing capacity 10 KA 'C' series complete all as specified and directed. |
| 43 | M & L for submain alongwith earth wire with the following size of FRLSH PVC two single core PVC copper conductor multistranded and including suitable size of PVC concealed and all accesssories concealed in wall /roof/ceiling etc. earth dolly , terminated in terminal box all as specified and directed for following Note :-(i) Two runs of copper conductor and one runs of earth copper conductor shall be measured as one length complete. (a)2x4 sqmm and 1x4 sqmm as earth wire. |
| 44 | S&F in repair Bib tap long body cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed. |
| 45 | S&F 100mm butt hinges extruded aluminium alloy with galvanised ms hinge pin anodised and fixed type C-21 complete all as specified & directed. |
| 46 | M&L for 100 mm long aluminium alloy handles, ofabricaatedtype, anodisedcomplete all as specified and directed. |
| 47 | Supply and fixing 500ltr capacity of rotational moulded polyethylene water storage tanks ( cylindrical verticle with closed top) hoisted and fixed in position all as specified in SSR Part II complete all as specified and directed. |
| 48 | M&L for 100 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 49 | S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 50 | Surface dressing not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified. |
| 51 | Excavation in soft / loose soil for post holes (or similar holes) each not exceeding 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed. |
| 52 | M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as specified and directed. |
| 53 | M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in embedding of precast post complete all as specified and directed. |
| 54 | M&L 10 mm thick rendering in CM 1:4 on brick or concrete surface finished even and and smooth without using extra cement complete all as specified and directed. |
| 55 | M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span,cills,step, sesmic & other similar bands plinth courses string courses, lacing course, parapets and railing upto 60cm in hight ,coping , kneelers, apex stones, bed plates , water troughs and the like including weathering , slightly rounded for chamfered angles and throating as complete all as specified and directed. |
| 56 | M&L moorum / red bajri filling in floors or pavings laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 57 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed. |
| 58 | Fabricated supply and fix GI pipe bracket suitable for 10/15w security light fitting , made out of 40mm dia 0.9m long & 2 set of the clamp made out of 30x5 mm md flat & fixed with anchor bolts complete all as specified and directed. |
| 59 | S&F square or rectangular Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed. |
| 60 | S&F mangalore partten Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPA as in roof covering/cladding to wall, including ridge of same colour fixed with self tapping screws as specified. |
| 61 | Pre-painted galvalume zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 MPA as in roof covering/cladding to wall, including ridge of same colour fixed with self tapping screws as specified. |
| 62 | Material & labour for preparation of new steel surfaces of any description over 10 cm width or girth not other wise described and applying two coats of synthatic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 63 | Excavation in trenches not exc 1.5m wide and not exc 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5 m depth in soft /disintegrated rock etc complete all as specified and directed |
| 64 | S&F reinforced concrete pipes, class NP-2, laid and jointed with collars of150 mm bore of pipe complete all as specified and directed. |
| 65 | M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregatecement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with complete all as specified and directed. |
| 66 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed |
| 67 | Demolition of stone slab and tiles of any description or thickness in floors, aprons etc complete all specified and directed. |
| 68 | All as per item no. 67 above bbut fixing only complete all specified and directed. |
| 69 | M & L for preparation of new plastered wall surface and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over 2mm thick water proof wall care putty complete all as specified and as directed. |
| 70 | M&L for non-skid joint ceramic coloured tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed. |
| 71 | M&L for preparation of newly plastered surfaces of wall and applying two coats cement base paint over a coat of pirmer complete all as specified and directed. |
| 72 | M&L for preparation surface of newly plastered ceiling and applying three coats of whitewash. |
| 73 | M&L for two coats synthetic enamel (ordinary tint) (each coat) paint over priming paints plaster coat including preparation new surfaces of kerb stones black / white / yellow colour, painting brick, stone, concrete, asbestos cement plaster surfaces plain or moulded and similar articles as required at site of any description over 10cm girth or width, not otherwise described complete all as specified and directed. |
| 74 | M& L for Providing PCC (1:24) type B1 using 20 mm graded agg as in coping complete all as specified and directed |
| 75 | S&F MS steel flat iron as in wind tie for roof sheet including securing bolts complete all as specified and directed. |
| 76 | M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed. |
| 77 | S&F of Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 78 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:6 and to be finished even and smooth (without using extra cement) complete all as specified and directed. |
| 79 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 80 | S&F mild steel angle as in posts/struts in fencing Kg including cutting, bending drilling holes, notching for wire etc, flat iron fillets for securing wire mess etc welding including all necessary drilling bolts or revetting etc conforming to Fe- 290 Gde E-165 etc. complete all as specified and as directed. |
| 81 | Fixing only MS galvanised chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, binding wire etc complete all as specified and directed. |
| 82 | Supply only MS galvanised chain link fencing any type and any gauge complete all as specified and directed. |
| 83 | S&F round bars for fixing of chain link fencing, in available length cut to shap, bent to shape requried, including cranking, bending spirally for hooping etc. complete and Fe-410 W (Gde E-250) quality-A or Fe 290 (Gde- E -165) complete all as specified and directed. |
| 84 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed .Note - Reinforcement and form work shall be measured and paid separately. |
| 85 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts and similar work complete all as specified and directed.Note - Reinforcement and form work shall be measured and paid separately. |
| 86 | S&F in repair,15 mm dia ,Pillar taps, cast copper alloy, fancy type,chromium plated,cast with capston heads screwed down high pressure,with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 87 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.Note - Reinforcement and form work shall be measured and paid separately. |
| 88 | M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work incl form work complete all as specified and directed.Note - Reinforcement shall be measured and paid separately. |
| 89 | M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed. |
| 90 | M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions for square, rectangular or polygonal for rough finished concrete surface complete all as specified and directed |
| 91 | M&L for Formwork to soffits of curved suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 92 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified & directed. |
| 93 | S&F Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending, hooking etc and binding with MS wire 0.9mm dia(annealed) complete all as specified |
| 94 | S&F Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending, hooking etc and binding with MS wire 0.9mm dia(annealed) complete all as specified |
| 95 | M&L for Brickwork with old size flyash bricks, straight or curved on plan exceeding 6m mean radius, built in 1:6 cement mortar complete all as specified & directed. |
| 96 | M&L for Brickwork with fly ash bricks in one brick thick honey-comb walling, built in 1:4 cement mortar complete all as specified & directed. |
| 97 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:6 and to be finished even and smooth (without using extra cement) complete all as specified and directed. |
| 98 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:4 and to be finished even and smooth (without using extra cement) complete all as specified and directed. |
| 99 | M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete.all as specified & directed. |
| 100 | S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed |
| 101 | S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 102 | S&F, in repair, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long Complete all as specified and directed. |
| 103 | S&F aluminium anodised tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. |
| 104 | S&F galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 105 | M & L preparing surface of newally plastered on walland applying wo coats of oil bond distemper over a coat of alkali resistant priming preparatory to distempering. |
| 106 | S & F 110 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints l complete all as specified. |
| 107 | S & F 75 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints l complete all as specified. |
| 108 | M&L for 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement, |
| 109 | Returning, filling in soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified & directed. |
| 110 | M&L for Removing surplus excavated material (soil) to a distance exceeding 250 metre but not exceeding 500 metre & depositing where directed complete all as specified & directed. |
| 111 | M&L PCC (1:2:4) type B-1 (20mm graded aggregate) as in kerbs/coping and the like includeing watering slightly ounded or chamfered angles and throating including formwork complete all as specified & directed. |
| 112 | S&F 15mm bore, angle /stop cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 20 mm bpre of pipe complete all as specified and as directed. |
| 113 | S&F 15mm size PVC connection with PTMT nuts of length 600mm |
| 114 | S&F PVC waste pipe 32/40mm dia 600mm long complete all as specified and directed. |
| 115 | S&F PVC waste pipe 32/40mm dia 600mm long complete all as specified and directed. |
| 116 | S&F, in repair, Health Faucet (ABS body) mild steel chromium plated suitable for 15mm dia a pipe with 1.25 metre long flexible tube (stainless steel), chromium plated for vitreous china padestal pattern water closet complete all as specified and directed. |
| 117 | S&F 75mm PVC (SWR) bends complete all as specified and directed. |
| 118 | S&F 110mm PVC (SWR) bends I complete all as specified and directed. |
| 119 | S&F 110 mm bore PVC (SWR) junction single, (single T) equal with provided access door complete all as specified and directed |
| 120 | S&F 75 mm bore PVC (SWR) branch piece single, (single y) equal equal or un equal complete all as specified and directed |
| 121 | S&F 110 mm bore PVC (SWR) branch piece single, (single y) equal equal or un equal complete all as specified and directed |
| 122 | S&F PVC (SWR) vent cowl 110mm complete all as specified and directed |
| 123 | M & L for Cement Concrete Type 1:3:6 Type C2 (using 20 mm graded stone aggregate as in surface channel and drain complete all as specified and directed. |
| 124 | M&L for 18 to 20 mm thick granite (table rubbed and polished ) as in step, jambs, pillars window-cills ,cooking platforms, and like, laid over and including 15mm thick cement screed base in CM (1:4) including pointing with white cement (1:2) using marble dust with admixture pigment to match with shade of slab complete all as specified and directed. |
| 125 | S&F MS framed work such as grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing framework of MS 'c' channel angle iron MS plate, nut &bolt etc for water tanks and simillar work Con-forming to Fe 290 Gde E-165 complete all as specified and directed. |
| 126 | M & L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI strip of size 32x6mm as lead by means of bolts, nuts, check nuts, and washers of galvanized iron or steel connecting to testing point including provision to testing point and all as shown in electrical plate No. 3 of SSR pt I. the work is inclusive of necessary earth work and PCC chamber in type CI (1:2:4) with 8 CTD bar reinforcement both ways at 140mm bents to centre complete all as specified and directed. |
| 127 | Supply & fix 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed. |
| 128 | Supply & fix 25mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed. |
| 129 | Supply & fix 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed. |
| 130 | M&L for 75mm thick PCC 1:4:8 type D2, using 40mm graded aggregate as in sub base complete all as specified and directed. |
| 131 | M&L for 100mm thick PCC 1:4:8 type D2, using 40mm graded aggregate as in sub base complete all as specified and directed. |
| 132 | M&L for PCC 100mm thick 1:2:4 type B2,as in floor finished the surface even and fair complete all as specified and directed. |
| 133 | M&L 75mm thick 1:3:6 type C2,as plinth protaction complete all as specified and directed. |
| 134 | M&L 80 mm thick glossy finish machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of M-40 grade complete all as specified & directed. |
| 135 | M&L 60 mm thick rubber moulded glossy finish machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of M-35 grade including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed. |
| 136 | M&L except 60 mm thick rubber moulded glossy finish machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of M-35 grade including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed. |
| 137 | M&L 60 mm thick rubber moulded glossy finish machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of M-35 grade complete all as specified & directed. |
| 138 | S&F glossy finished Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 139 | S&F glazedceramic coloured & digital tiles 350 x 250x 7mm/ 450x350x7mm thick, set, jointed and pointed in neat cement slurry in floors over 10 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 140 | Supply & fix in vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but plastic water closet seat cover complete all as specified and directed. |
| 141 | Supply & fix in vitreous china white counter oval shape wash hand basin of size 630x450mm incl bracket complete all as specified and directed. |
| 142 | stack clamps, out of 50mm by 5mm flat iron stays, and 16mm dia round stay including bolts and nuts and securing ends of stays to wall or roof |
| 143 | S&F modular type switch , one way 6 Amp ,1 module complete all as specified and directed. |
| 144 | S&F modular type socket 5 pin 6 Amp ,2 module complete all as specified and directed. |
| 145 | S&F modular type switch one way 16 Amp ,1 module complete all as specified and directed. |
| 146 | S&F modular type socket 5 pin 6 A/16Amp ,2 module complete all as specified and directed. |
| 147 | S&F ceiling rose surface , backelite , thre terminal 240 volts complete all as specified and directed. |
| 148 | S&F UPVC waste pipe in any length with and without ears with cement joints fixed to wall 100mm dia complete all as specified and directed. |
| 149 | M&L for flame proof point wiring with 1.50 sqmm size , single core, multistranded copper conductor FRLSH unsheathed PVC insulated heav duty cable in colour code including felxible FRLSH insulated drawn in a including concealed PVC ridid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit including modular galvanside flush boxes of sutable size and white cover plate with frame as per relevant IS for mounting modular switches , sockets , fan regulator etc complete all as specified & directed. |
| 150 | (a) One light point controlled by one, one way switch 6 Amps |
| 151 | (b) One exhaust fan point controlled by one, one way switch 6 Amps completed |
| 152 | (c) One 3 point 6 Amps switch socket outlet same board. |
| 153 | (d) One 3 point 6 Amps switch socket outlet independent board. |
| 154 | (c) One 3 point 6 Amps switch socket outlet independent board. |
| 155 | All as per item No 149 but for 1 point socket outlet 16 Amp independent with cable of size 2.5 sqmm for point wrining and 2.5 sqmm as in continous earth wire. |
| 156 | Schedule of credit amount of Rs. 0.00 to be deducted during AOC Please Enable Macros to View BoQ information |
