|
| 1 | Notes: (i) The scope of subject work involves repair and rectification all day to day complaints received from users and other miscellaneous repairs ordered by the Engineer-in-charge time to time during currency of work till date of completion. Hence the site will be handed over to the contractor as per complaints received from the users and as per the requirement. Contractor shall have no claim whatsoever in this aspect. (ii) The contractor or his representative shall collect daily list of complaints from MES complaint cell or from concern JE and shall attend all the complaints in the same day irrespective of number of complaints received. Contractor shall employ sufficient tradesmen accordingly as per requirement. However minimum one plumber and carpenter shall be made available throughout working hours to attend emergency complaints. The rates quoted by the contractor shall be deemed inclusive of cost against supervisor, all tradesmen / labours employed, conveyance required for collecting complaints and attending at site for all items of BOQ. (iii) Contractor shall employ skilled / experienced tradesmen and workers for execution of work. (iv) Contractor or his representative shall submit compliance report of complaints on the same day with receipt / job card duly signed by the users to concern JE. Contractor may use separate register for each category of complaints and obtain signature from users after repair / rectification of complaints received and submit the same during preparation of RARs to concern JE. (v) All critical complaints related to water supply and complaints which posses safety hazards to occupants have to be rectified within 24 hours after receipt of complaints. In case of complaints are not rectified on same day, the contractor shall submit in writing to Engineer-in-charge with valid reasons / justifications for delay and however the same shall be rectified with in 2 working days. Otherwise a recovery of Rs 500 per complaint shall recovered from the contractor. (vi) All unserviceable materials, debries, waste material scrap etc. obtained during repair work other than such of credit materials issued to the contractor shall be removed immediately from site and disposed off at dumping locations earmarked with in the INA premises at no additional cost to the Govt. The cost of labour, transportation etc. shall be deemed included in the rates quoted by the contractor against respective BOQ items and nothing extra shall be paid. (vii) While attending water supply pipeline repairs, tank replacement / cleaning works, or other external works, Contractor may require ladders, site clearance / cutting of vegetation, bushes etc. to make approach to enable work at his own arrangement without any additional cost to the Govt. |
| 2 | Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each and refixing the same after carrying out repairs including providing new necessary aluminium / MS rods as extra stiffening members for doors and refixing in same position all as specified and as directed. |
| 3 | Dismantling wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/ slabs/ any thickness including cover fillets all as specified and as directed. |
| 4 | Material & labour 4mm thick non-asbestos fiber cement building boards with decorative finish on one face fixed or laid/inserted to timber, GI/aluminium framework with screws all as specified and as directed. |
| 5 | Supply & fix in repairs anodised aluminium snap grid frame work for false ceiling. The snap grid frame work shall be fixed to ceiling with supporting hanger consisting of 6mm dia mild steel rod, J bolts with necessary bolts, nuts and washers. The snap grid (main/cross tee section) supported at ends shall be 40mm x 25mm x 2mm weighing 0.36 Kg/RM and the main & cross tee shall be jointed at junction/ crossing with angle bracket of size 15mm x 15mm x 1.5mm, weighing 0.12 Kg/RM and fixed with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specifiedall as specified and as directed. |
| 6 | Taking down chowkats or frames any description and size but without taking off shutters from the frames n exc 1.5 sqm all as specified and as directed. |
| 7 | Taking down shutters of any description and any material n exc 1.5 sqm all as specified and as directed. |
| 8 | Supply & fix Powder coated aluminium sections for frame and shutters of doors, windows, ventilators, partitions etc with one or more rebates including necessary neoprene packing etc complete all as specified and as directed.Note:- Minimum thickness of powder coating not less than 50 Micron |
| 9 | Supply & fix in repairs Aluminium Composite Panel 4mm thick of approved colour and shade fixed to wooden / aluminium frame work as in door/cupboard shutters all as specified and as directed. |
| 10 | Supply and fix in to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 11 | Supply and fix Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 12 | Supply & fix 150mm aluminium barrel tower bolt of extruded section ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.all as specified and as directed. |
| 13 | Supply & fix 150mm extruded aluminium alloy handles fabricated type ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 14 | Supply & fix 100mm stainless steel butt hinges, IS :12817 marked cold rolled medium weight all as specified and directed |
| 15 | Supply & fix 150mm stainless steel butt hinges, IS :12817 marked cold rolled medium weight all as specified and as directed |
| 16 | Supply & fix 300mm aluminum alloy ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and as directed. |
| 17 | Supply & fix mortice lock 100 mm to 150mm long matching with the existing doors and locks all as specified and as directed. |
| 18 | Supply & fix floor door stopper 150mm size aluminium alloy body and tongue double legged, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc fixed to door all as specified and as directed. |
| 19 | Supply & fix in repairs 75 mm aluminium barrel tower bolt of extruded section ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. all as specified and as directed. |
| 20 | Supply & fix in repairs 100 mm aluminium barrel tower bolt of extruded section ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 21 | Supply & fix in repairs 150mm aluminium barrel tower bolt of extruded section ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 22 | Supply & fix in repairs100 mm extruded aluminium alloy handles fabricated type, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 23 | Supply & fix in repairs150mm extruded aluminium alloy handles fabricated type ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc all as specified and as directed. |
| 24 | Supply & fix in repairs 75 mm stainless steel butt hinges, IS :12817 marked cold rolled medium weight F130 all as specified and as directed. |
| 25 | Supply & fix in repairs 100 mm stainless steel butt hinges, IS :12817 marked cold rolled medium weight all as specified and as directed. |
| 26 | Supply & fix in repairs aluminium powder coated Ebco handles, suitable for locking windows / ventilators all as specified and as directed. |
| 27 | Supply & fix in repairs 250 mm aluminum alloy ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloyall as specified and as directed. |
| 28 | Supply & fix in repairs 300mm aluminum alloy ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and as directed. |
| 29 | Supply & fix in repairs mortice lock 100 mm to 150 mm long suitable for existing Aluminium doors matching with the existing all as specified and as directed. |
| 30 | Supply & fix in repairs aluminum tubular towel rail 20mm dia SI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. including brackets complete all as specified and as directed. |
| 31 | Supply & fix in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. including brackets complete all as specified and as directed. |
| 32 | Supply & fix in repairs floor door stopper 150mm size aluminium alloy body and tongue double legged, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc fixed to door.all as specified and as directed. |
| 33 | Supply & fix in repairs aluminum (die cast) body door closer hydraulically regulated designation No 2 universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg all as specified and as directed. |
| 34 | Supply & fix in repairs aluminium coat hook solid body matching with existing ones all as specified and as directed. Please Enable Macros to View BoQ information |
| 35 | Supply & fix in repairs aluminium coat hook solid body matching with existing ones all as specified and as directed. Please Enable Macros to View BoQ information |
